M5STACK St.amp-S3Bat brugervejledning til indlejret kernemodul

M5STACK St.amp-S3Bat Embedded Core Module

Beskrivelse

Stamp-S3Bat is an embedded core module integrated with power management. It utilizes the ESP32-S3-PICO-1-N8R8 as the main control core, supports 2.4GHz Wi-Fi, and comes with built-in 8MB Flash and 8MB PSRAM.
It provides 11 GPIO pins, an onboard battery power interface, and can be directly connected to an external 3.7V lithium battery for power supply.

With an efficient built-in PMIC and multi-level power control design, it supports power input and output control, as well as status monitoring for input voltage og batteri voltage. It supports external low-power wake-up. After the main controller shuts down and enters low-power sleep mode, it can be triggered to wake up via an external PMIC wake-up IO. The module features an onboard user button and a programmable RGB LED. With 2.54mm standard-pitch half-hole solder pads, it can be integrated into your applications through SMT, DIP, or other methods, helping developers quickly build IoT applications.

Specifikationer

Hurtig start

Forberedelse

1. Besøg den officielle Arduino webwebsted og installer Arduino IDE'en
   https://www.arduino.cc/en/Main/Software
2. Tilføj følgende bestyrelsesadministrator URL til File → Indstillinger → Yderligere opslagstavler URLs:
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Åbn Boards Manager, søg efter “ESP32”, og klik på installer.
4. After installation, select the board “ESP32S3 Dev Module”.
5. Configure the following options. USB CDC On Boot: “Enabled”, PSRAM： “OPI PSRAM”, USB Mode: “Hardware CDC and JTAG"

Wi-Fi-scanning

• Vælg exampprogrammet "Eks.amples” → “WiFi” → “WiFiScan”, vælg den port, der svarer til din enhed, og klik på knappen "kompiler og upload" i øverste venstre hjørne.
• Når uploaden er færdig, skal du åbne Seriel skærm for at view Wi-Fi-scanningsoplysninger.

BLE Scan

• Vælg exampprogrammet "Eks.amples” → “BLE” → ”Scan”, vælg den port, der svarer til din enhed, og klik på knappen "kompiler og upload" i øverste venstre hjørne.
• Når uploaden er færdig, skal du åbne Seriel skærm for at view Oplysninger om BLE-scanning.

FCC advarsel

FCC advarsel:
Ændringer eller modifikationer, der ikke udtrykkeligt er godkendt af den part, der er ansvarlig for overholdelse, kan annullere brugerens ret til at betjene udstyret.

Denne enhed overholder del 15 af FCC-reglerne. Driften er underlagt følgende to betingelser:

1. Denne enhed må ikke forårsage skadelig interferens, og denne enhed skal acceptere enhver modtaget interferens, herunder interferens, der kan forårsage uønsket drift.

VIGTIG BEMÆRKNING:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use,s and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Drej eller flyt modtagerantennen.
• Øg afstanden mellem udstyret og modtageren.
• Tilslut udstyret til en stikkontakt på et andet kredsløb end det, som modtageren er tilsluttet.
• Kontakt forhandleren eller en erfaren radio/tv-tekniker for at få hjælp.

FCC-erklæring om strålingseksponering:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated wita h minimum distance of 20cm between the radiator & your body.

Ofte stillede spørgsmål