Keeson RC309B Remote Control User Manual

Keeson RC309B Remote Control

Specifikationer

• Produktnavn: FJERNBETJENING
• Model: RC309B
• Input: 2 x Battery AAA 1.5V
• Fabrikant: Keeson Technology Corporation Limited
• Manufacturing Country: Kina

Brugsvejledning

Figure 1 illustrates the buttons on the remote control.

Hovedet op

1. Press and hold the HEAD UP button of the remote, the head actuator moves out, stop when released.
2. Hovedet ned
   Press and hold the HEAD button of the remote, the head actuator moves in, stop when released.
3.  Foden op
   Press and hold the FOOT UP button of the remote, the foot actuator moves out, stop when released.
4. Foden ned
   Press and hold the FOOT button of the remote, the foot actuator moves in, stop when released.
5. Flad
   Click the FLAT button, the bed goes flat, stop when you click any button during the process of going flat.
6. Massage hoved
   Click the MASSAGE HEAD button, head massage motor switches massage intensity, massage intensity switches among 0-1-2;
7. ZG knap
   Click the ZG button, the actuator moves to the ZG position, stops when clicking any button, dilling the movement;
8. Memory Favorite position
   Clicking once will move the app to the Favorite position; long press to memorize the position, the backlight will flash twice, and releasing the button will continue the flashing.
9. Memory Fvorite2 position
   Clicking once will move the app to the Fav01ite2 position; long press to memorize the position, the backlight will flash twice, and releasing the button will continue the flashing.
10. Låse
    Press and hold the child lock button until the red light flashes twice, indicating that the child lock is successfully engaged. Dialing the locking process, pressing any button will cause the red light to flash for 2 seconds, indicating that the lock is engaged.

FCC:

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tlY to conect the interference by one or more of the following measures:

• Drej eller flyt modtagerantennen.
• Øg afstanden mellem udstyret og modtageren.
• Tilslut udstyret til en stikkontakt på et andet kredsløb end det, som modtageren er tilsluttet.
• Kontakt forhandleren eller en erfaren radio-tv-tekniker for at få hjælp.

Ændringer eller modifikationer, der ikke udtrykkeligt er godkendt af den part, der er ansvarlig for overholdelse, kan annullere brugerens ret til at betjene udstyret. Denne enhed overholder del 15 af FCC-reglerne. Driften er underlagt følgende to betingelser:

1. Denne enhed må ikke forårsage skadelig interferens,
2. This device must accept any interference received, including interference that may cause undesired operation to accept any interference received.

Oplysninger om RF-eksponering

The device has been evaluated to meet the general RF exposure requirements. The device can be used in exposure conditions without restriction.

ISED RSS-advarsel:

This device complies with Innovation, Science and Economic Development Canada licence, exemplifying RSS standard(s). Operation is subject to the following two conditions:

• Denne enhed må ikke forårsage interferens.
• Denne enhed skal acceptere enhver interferens, inklusive interferens, der kan forårsage uønsket drift af enheden.

Fejlfinding

If the remote control is not functioning as expected:

• Tjek batterier: Ensure that two AAA 1.5V batteries are correctly inserted and have sufficient charge.
• Børnelås: If the remote is unresponsive and the red light flashes for 2 seconds when a button is pressed, the child lock may be engaged. Refer to section 1.7 to disengage the child lock.
• Interferens: This device complies with FCC rules regarding interference. If you experience unexpected operation, it might be due to external interference. Ensure there are no strong radio frequency sources nearby.

Ofte stillede spørgsmål

• Hvordan skifter jeg batterierne?
  The remote uses 2 x AAA 1.5V batteries. Open the battery compartment, remove the old batteries, and insert new ones, ensuring correct polarity.
• What does the ‘ZG’ button do?
  The ‘ZG’ button moves the bed to a pre-set Zero Gravity position, which is often considered an optimal position for comfort and pressure relief.
• Can I customize the ‘Favorite’ positions?
  Yes, you can memorize your preferred head and foot positions for both ‘Favorite 1’ and ‘Favorite 2’ by long-pressing the respective buttons.
• What should I do if the remote’s red light flashes when I press a button?
  If the red light flashes for 2 seconds when you press a button, it indicates that the child lock is engaged. You will need to disengage it to use the remote.
• Are there any restrictions on where I can use this device?
  This device has been evaluated for general RF exposure and can be used in portable exposure conditions without restriction.
• What if I make unauthorized changes to the equipment?
  Eventuelle ændringer eller modifikationer, der ikke udtrykkeligt er godkendt af den part, der er ansvarlig for overholdelse, kan annullere brugerens ret til at betjene udstyret