VIMAR Linea XT Platform Control Device Instruction Manual

VIMAR Linea XT Platform Control Device

Specifikationer

• Produktnavn: WELL-CONTACT PLUS
• Modelnummer: 32142.x
• KNX Data Secure
• Equipped with a dedicated QR code for ETS (version 5.5 and later)
• Integrated with four sensors

Indledning

Linea XT platform control device, KNX standard, thermostat function for ambient temperature control (heating and air-conditioning), 2- and 4-pipe system management, 3-speed and proportional fan coil control, class I temperature control device (contribution 1%) in ON/OFF mode, class IV (contribution 2%) in PID mode, can be interfaced with actuator with proportional analogue outputs to create a class V modulating room thermostat (contribution 3%), humidistat function with ON/OFF control with respect to a set parameter, VOC (volatile organic compound) function with ON/OFF control, proportional or to call up 2 scenarios, 2 push button function with configuration also as 1 rocker button with status identification LED, central LED matrix to customise symbols or animation, proximity function, white LED backlighting – 2 front modules
The device is KNX Data Secure and is equipped with a dedicated QR code to be used with ETS (version 5.5 and later) during configuration.

Enheden er integreret med følgende fire sensorer:

• Temperaturføler
  The temperature sensor is integrated with the KNX home automation system and allows the current temperature to be shown on the display or the data to be sent to the bus. It can be used in the thermostat function to manage temperature control in 2 or 4 pipe systems (heating/conditioning) and neutral zone (4 pipe systems only), with “boost” function to run a second source to reach the desired thermal comfort quicker. The 4 available outputs (hot, cold, second stage hot, second stage cold) for the fans can be configured to control 3-speed fan coils, proportional fan coils or to control HVAC type split/VRV systems via third-party KNX interfaces (if the first stage controls split/VRV systems, the second cannot do so). The thermostat is fitted with a white LED matrix display and 2 keys to control the temperature setpoint and to turn the temperature control system on/off. Opposite each key are white LEDs for the “up and down arrow” or “+ and -” symbols. There are also two LEDs that indicate the heating valve control phase (amber or configurable white LED) or cooling phase (blue or configurable white LED). During the configuration phase, you can choose whether to view the room temperature, the current setpoint or the current setpoint delta normally. The thermostat can control proportional fan coils, 3-speed fan coils or HVAC type split/VRV systems via third-party KNX interfaces.
• Fugtføler
  The humidity sensor is integrated with the KNX home automation system and allows the current humidity to be shown on the display or the data to be sent to the bus. It also allows the humidistat function by sending an On/Off control on the bus when the humidity value increases or decreases with respect to a parameter set during the configuration phase. It can be used to manage ventilation and for dewpoint management, in combination with the temperature.
• VOC air quality control sensor
  The VOC (volatile organic compounds) sensor is integrated with the KNX home automation system and allows the air quality variations to be shown on the display or the data to be sent to the bus. It also allows the sending of an On/Off control or to call up 2 scenarios when the air quality worsens or improves with respect to parameters set during the configuration phase. The VOC sensor, in combination with temperature and humidity, makes it possible to manage ventilation to improve the quality of the air.
• Nærhedssensor
  The proximity sensor (the sensitivity of which can be set from ETS) enables the multisensor activation by approaching a hand at a distance set during the configuration phase. Activation propagates the information to the other controls on the same electrified XT mounting frame. The time on standby is configurable. Proximity detection can be associated with the sending of a bit control or the calling up of a scenario.

Enheden kan bruges på følgende måder:

• Tilstand 1 – “Master thermostat”: Locally controlled thermostat for ON/OFF + setpoint adjustment, possibly with interface block function (as per parameter) without symbols on the keys. The symbols of the upper and lower keys can be customised, choosing from a list on ETS.
  Det tillader:
  • Viewing of temperature and setpoint on central display. If the climate control art. 32144.x is present, values T, H and VOC will be shown on the display every time the key is pressed.
  • Redigering af værdierne: summer_winter/fan speed/Celsius_Farenheit/on_off ved hjælp af de eksterne taster på klimastyringen.
• Tilstand 2 – “Slave thermostat”: It only works as a remote user interface for the master thermostat and as a viewer for the internal sensors for internal temperature, humidity, and air quality. The slave thermostat can modify the setpoint set on the master thermostat by sending the new value to the bus. The average temperature calculated with related weighting and distributed by the master thermostat can be displayed on both the master thermostat and the slave thermostats. Temperature control is performed by the master thermostat based on the average temperature. For this function to work, the slave thermostats must send their detected temperature to the master thermostat, which then distributes the average temperature to be displayed and the setpoint.
• Tilstand 3 – “Sensor viewøh”: Viewer of the values T, Text, H and VOC on the display. It is used as a simple viewer and normally shows the current temperature. Using the two keys on the device (or with climate control art. 32144.x) the values of the local temperature, remote probe temperature, humidity and air quality can be browsed and displayed.
• Tilstand 4 – “Rocker switch/push button control”: Control with 2 push buttons or 1 rocker switch where the 2 keys can be configured as 2 push buttons or grouped together as 1 rocker switch. The symbols of the upper and lower keys can be customised. In the case of 1 rocker switch the central white LED matrix can be used for customised symbols or for animation, while in the case of 2 push buttons it can be used to display any alarms, load status and scenario activation with customised symbols. The values T, H and VOC are not shown on the display but they are made available on the bus.
• Tilstand 5 – “Push button control/rocker switch with thermostat function”: Control with 2 push buttons or 1 rocker switch where the 2 keys can be configured as 2 push buttons or grouped together as 1 rocker switch + thermostat.
  Symbolerne på den øverste og nederste tast kan tilpasses. I tilfælde af 1 vippekontakt kan den centrale hvide LED-matrix bruges til tilpassede symboler eller til animation, mens den i tilfælde af 2 trykknapper kan bruges til at vise eventuelle alarmer, belastningsstatus og scenarieaktivering med tilpassede symboler.
  The values T, H and VOC are not shown on the display but they are made available on the bus.
• Tilstand 6 – “Room number”: Allows you to view the room number from 0 to 9999. The lower push button can be programmed for “bell” function with message sending on the bus.

Funktioner tilgængelige for hver tilstand

• Humidity/air quality/external temperature values made available on the bus.
• Sending of ON/OFF controls when the humidity value measured increases/decreases with respect to a threshold configured on ETS (sending of two controls in reference to two thresholds).
• Sending of ON/OFF control or activation of two scenarios when the air quality improves or worsens with respect to a threshold configured on the ETS App.
• Wake-up of device upon external events (e.g. change in contact interface status, PIR sensors).
• Sending of ON/OFF control or activation of a scenario upon proximity detection

KARAKTERISTIKA

• Strømforsyning: leveres med elektrificeret XT monteringsramme art. 32602.x, 32603.x, 32604.x eller 32614.x og relateret nodeart. 32101.
• Maximum absorption from the BUS: 15 mA TP1-256.
• Rød LED og konfigurations-/nulstillingsknap
• Bagtilslutning til den elektrificerede XT monteringsramme 32602.x, 32603.x, 32604.x eller 32614.x.
• Optager 2 frontmoduler størrelse 30.5 mm
• Lysstyrke på standby-niveauer, der kan vælges fra de relaterede parametre
• Hysterese: justerbar fra 0.1°C til 1°C.
  Temperaturmålingsnøjagtighed af den indbyggede sensor: måleområde fra 0 til 40°, ±0.5 °C mellem 15 °C og 30 °C, ±0.8 °C ved ekstremerne.
• Præcision af integreret sensor fugtmåling: ± 6RH% typisk (i stillestående luft ved 20 °C og 50RH%)
• Ledelse af 2- og 4-rørs systemer.
• Heating, air conditioning with management of the neutral zone.
• Operation via a dedicated ON/OFF or 6-way or proportional hot/cold valve actuator (0-10 V, 4-20 mA).
• Fan coil management (3-speed/proportional and split/VRV system control).
• Valgbar PID eller ON/OFF kontrolalgoritme:
  • ON/OFF-algoritmen er styringen, som ved overskridelse af den indstillede temperatur øget med tærskelværdien (omvendt for aircondition), slukkes for varmen for derefter at blive tændt igen, når rumtemperaturen falder til under den indstillede temperatur.
  • PID is a sophisticated algorithm capable of keeping the temperature in the room more stable and it works by switching the system on and off so as to be like a gradual increase or decrease in the system’s thermal (or refrigerating) power; ideal for use in floor heating systems, the algorithm needs to be properly calibrated according to the type of environment and system.
  • Boost-funktion: styring af en hjælpeaktuator for at fremskynde opvarmning eller aircondition af miljøet.
• Mild sæson funktion: tilgængelig fra supervisor kun for systemer konfigureret med 4 rør; når den er aktiv, styres den sekundære udgang med sine egne parametre.
• Possibility of using external sensors connected to the bus for:
  • Udskiftning af den interne sensor.
  • Gennemsnitlig med den interne.
  • Afretningstemperaturbegrænsning.
  • Visning kun på display.
• Open window management function with delayed power on management.
• Device can be interfaced natively with third-party systems (KNX systems).
• Fjernstyrbar enhed.
• Anti-stratification function that compares temperatures detected at 2 different heights within the room. If the temperature difference exceeds the value set in a parameter, it controls the fans to run at minimum speed without activating the valve.
• Mulighed for at bruge en offset til at korrigere aflæsningen af ​​den målte temperatur i henhold til et evtample termometer for at kompensere for fejl som følge af specielle installationer (nordvendt væg, nærhed til varmt-/koldtvandsrør mv.).
• The thermostat can be controlled from a key on the device 32144.x for the ON/OFF, scrolling the viewværdier, opvarmning/køling, ændring af ventilatorhastighed, ændring af grader Celsius/Fahrenheit, visningsfunktioner.
• Fugtkontrol: kontrol af en aktuator for at aktivere befugtnings- eller affugtningssystemer.
• Luftkvalitetskontrol: kontrol af en aktuator for at aktivere luftrecirkulationssystemer. Fremkaldelse af scenarier, hvis luftkvaliteten forbedres eller forværres.
• Dugpunktsberegning: hvis der er risiko for dugdannelse, slukkes termostaten og sender et alarmsignal på bussen til det dedikerede objekt (den leveringstemperatur, der kræves til beregningen, kan modtages via bus eller indstilles fast ved hjælp af en parameter) .
• 17×7 LED matrix; when configured as 2 push buttons or 1 rocker switch a 5×5 matrix is used.
• Driftstemperatur: 0 °C – +40 °C (-T40, indendørs brug).
• ErP-klassificering (EU-forordning 811/2013):
  • TIL/FRA: klasse I, bidrag 1%;
  • PID: klasse IV, bidrag 2%;
• Configuration from ETS software.
• Beskyttelsesgrad: IP30
• Sporingsindeks: PTI175
• Forureningsgrad: 2 (normal)
• Rumtemperatur under transport: -25 – +60°C
• Softwareklasse: A

KONFIGURATION

For all the details relating to the ETS communication objects and to the device configuration, please consult the Well-contact Plus manual available for downloading under “Download -> Software -> Well-contact Plus” on the www.vimar.com webwebsted.
Using the front keys, the user can modify the temperature set point and the speed of the fan coil; modifying these parameters forces the device into manual operation.

INSTALLATIONSREGLER

• Installation og konfiguration skal udføres af kvalificerede personer i overensstemmelse med de gældende regler vedrørende installation af elektrisk udstyr i det land, hvor produkterne er installeret.
• Enheden skal installeres på elektrificerede XT-monteringsrammer med:
  • 2 moduler art. 32602.x (til 2-modul monteringsboks)
  • 3 modules art. 32603.x (for rectangular 3-module mounting box)
  • 4 moduler art. 32604.x og 32614.x (til 4-moduls rektangulær monteringsboks)
• To obtain the temperature and humidity performance levels declared, the device should be installed in the furthest place to the right in the electrified XT mounting frame 32602.x, 32603.x, 32604.x; what’s more, a maximum of one actuator can be installed at the back in the furthest place to the left in electrified XT mounting frames 32603.x and 32604.x.
  If this type of installation is not observed, an offset can be set (the temperature and humidity measurement accuracy is however not guaranteed).
• Apparatet skal overflademonteres ved hjælp af den elektrificerede XT monteringsramme, typisk i en højde på 1.5 m over gulvniveau, i en passende position til korrekt registrering af rumtemperaturen, undgå installation i udsparinger, bag døre og gardiner, områder påvirket af varmekilder eller udsat for strømmen af ​​tvungen varme-/køleventilationskilder eller påvirket af atmosfæriske faktorer. Undgå især installation på perimetervægge eller i forbindelse med enheder, der genererer varme (f.eks. lysdæmpere eller lamps).
• To optimise operation, we recommend leaving only one proximity sensor (proximity function) active per lighting device, disabling the others.
• Avoid installing two or more controls with an active proximity sensor (proximity function) facing one another if the distance is less than 4 m:
• Avoid installing a key with an active proximity sensor (proximity function) directly in front of a device with an infrared receiver to prevent potential interference.

OVERHOLDELSE AF REGULERING.

LV-direktivet. EMC direktiv. RoHS direktiv.
Standards EN 60730-2-9, EN 50491-2, EN IEC 63044, EN IEC 63000, EN 60730-2-13.
Temperaturreguleringsanordning (EU) nr. 811/2013.
REACH (EU) forordning nr. 1907/2006 – art.33. Produktet kan indeholde spor af bly.

WEEE – Brugeroplysninger

Det overstregede skraldespandssymbol angiver, at produktet skal sendes til separate indsamlingssteder til genanvendelse og genbrug i overensstemmelse med de nationale love i EU-lande, der implementerer WEEE-direktivet. Målet er at forhindre skadelige virkninger på miljøet og menneskers sundhed ved at sikre, at produkter bortskaffes korrekt, undgå ulovlig bortskaffelse, som er sanktioneret ved lov. For at bortskaffe produktet korrekt, bedes du kontrollere lokale dispositioner i dit land.

FORAN OG BAG VIEW

• A: Red LED
• B: Proximity sensor
• C: Configuration/Reset push button
• D: Push button and white LED matrix

TILKOBLING AF ENHEDEN

FJERNELSE AF ENHEDEN

Viale Vicenza 14
36063 Marostica VI – Italien www.vimar.com

Ofte stillede spørgsmål