THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Hurtig startvejledning

Pakkens indhold

Specifikationer

Fabriksindstilling

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Scan QR-koden til view detaljer

https://bit.ly/488mkj9

Fejlfinding

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. Enheden vil ikke tænde
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

FCC-lovoverholdelse
Denne enhed overholder del 15 af FCC-reglerne. Betjening er underlagt følgende to betingelser: (1) Denne enhed må ikke forårsage skadelig interferens, og (2) denne enhed skal acceptere enhver modtaget interferens, inklusive interferens, der kan forårsage uønsket drift.
Enhver ændring eller modifikation, der ikke udtrykkeligt er godkendt af den part, der er ansvarlig for overholdelse, kan annullere brugerens ret til at betjene udstyret.
Note: Dette udstyr er blevet testet og fundet i overensstemmelse med grænserne for en klasse B digital enhed i henhold til del 15 af FCC-reglerne.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Drej eller flyt modtagerantennen.
– Øg afstanden mellem udstyret og modtageren.
– Tilslut udstyret til en stikkontakt på et kredsløb, der er forskelligt fra det, som modtageren er tilsluttet.
– Kontakt forhandleren eller en erfaren radio/tv-tekniker for at få hjælp.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

For begrænset garanti, besøg venligst
https://thirdreality.com/faq-help-center/
For kundesupport, kontakt os venligst på
info@3reality.com eller besøg www.thirdreality.com
For spørgsmål om andre platforme, besøg de tilsvarende
platform’s application/support platform.