NOTHING Fixed Frame Screen Instruction Manual

NOTHING Fixed Frame Screen

Tak, fordi du har valgt at bruge vores produkt! For at du bedst muligt kan bruge produktet, bedes du læse og opbevare denne manual omhyggeligt inden installation og brug.

Every screen undergoes special quality checks. The manufacturer records a video of each screen produced in the factory to document the condition of the screen as ii leaves the factory. We recommend that you also record a video for documentation when unpacking the screen. This will facilitate the manufacturer in processing any service requests in case of issues. Damage that occurs during the installation cannot be claimed. Therefore, please be extremely careful as the screen material is very fragile, and avoid folding or denting it.

Dele

Forholdsregler

1. For at sikre projektionseffekten og kvaliteten af ​​dette produkt, skal du overholde følgende driftskrav.
2. Find et passende gulv eller bord ved montering. Overfladen skal være ren og fri for forhindringer. Gulvet eller bordet skal dækkes med rene materialer som klud, film, tæpper mv.
3. Håndteres med forsigtighed under installationen for at forhindre personskade eller ejendomsskade.
4.  Rør ikke ved overfladen af ​​projektionsskærmen med hænderne.
5. Rør ikke projektionsoverfladen med skarpe eller hårde genstande for at forhindre beskadigelse af skærmmaterialet. Skriv eller tegn ikke på skærmen.
6. Hold børn væk fra skærmen for at forhindre ulykker.
7. Skærmens overflade skal rengøres og behandles regelmæssigt, og det anbefales at pleje den en gang hver anden uge.
   Please use a soft cotton cloth to gently wipe (dip some water), and it is not advisable to use any chemical cleaners or alcohol.

Saml rammen

1. Åbn emballagen og kategoriser og arranger komponenterne korrekt, og krydshenviser mængderne med tjeklisten "1.0 Parts".
2.  The horizontal frame is a segmented splicing type, and the two horizontal inner frames are spliced correspondingly as shown in the figure (Note: There is a mark in the middle of the splicing strip of the inner frame, and the splicing position must be guaranteed to be at the mark).
3. Først skal du indsætte de fire hjørneforbindelser i den lodrette inderramme, som vist på diagrammet.
4. Saml de vandrette og lodrette inderrammer i henhold til diagrammet. Når du har samlet inderrammerne, skal du fastgøre hjørnerne med M5X5-skruer, og derefter montere støttestængerne.

Saml skærmen

1.  Wear gloves (to avoid fingerprints on the screen that cannot be erased).Lay a clean cloth I’ non a flat, clean level countertop (or floor) that won’t hurt the screen.
2.  Take out the screen from the package, put the screen face down,to unfold the curtain roll, spread it flat on the cloth on the table, and then insert the glass fiber strips into the around the screen according to the length as shown below. Vigtig bemærkning:
   Hvis det er en skærm, der afviser omgivende lys med ultrakort kast, bedes du samarbejde med to personer under monteringen, undgå foldning af skærmen eller stød på hårde objekter.
3. Place the assembled border on the screen. Note: The ultra-short focus anti-light scree has an up-and-down direction (other curtains have no direction). If it is an anti-light screen it should be matched with the direction of the frame. Adjust the position of the screen according to the lines marked on the four corners of the screen.
4.  Hook the screen on the frame with a tension spring. To hook the tension spring, please follow the following sequence, first, hook 1~8 springs; then hook springs 9~12, and then hook other springs from the middle spring to both sides in turn. Please refer to the attache drawing for the installation method of the tension spring
5. Efter at have hængt fjederen op, skal du stille skærmen op og kontrollere skærmens generelle planhed. Hvis der er ujævnheder, skal fjederen justeres lokalt, indtil den er i vater.
6. Is restored to the position of 4.4, ready to install the frame.

Montering af udvendig ramme

1. Placer den ydre ramme mod rammeskærmen, juster de fire hjørner, og fastgør den indre og ydre ramme med M4X8 skruer. Bemærk: Hvis der er et LOGO på rammen, skal det monteres nederst på skærmen.
2. Adjust the outer frame at the corner to the smallest gap, and then tighten the screws. Lock the corners one by one according to this method, and finally deal with the splicing of the horizontal outer frame (if the gap is found to be too large, you can push the left and right outer frames inward)
3. Til sidst sættes hjørnebeskytterne på rammens fire hjørner.

Skærminstallation

1. Bekræft først det øverste og underste vægbeslag og monteringsretningen
2. Install wall hangers on the wall according to screen size. Required tools: level, hammer drill, pencil, ladder, etc. As shown below, the horizontal direction is about 30cm away from both sides of the screen. Please estimate the installation position of the screen before installing the wall pendants. The height of the lower edge of the screen from the ground is generally about 600″800mm.
3. Hang the screen on the wall according to the method shown in the picture.

Ofte stillede spørgsmål