MOZA RACING MTQ Throttle Quadrant
Produktspecifikationer
- Mål: 166.4mm x 216.1mm x 197.3mm
- Mounting: 6 X M4, 2 X M6
- Vægt: 45.0 gram
- Friction Adjustment Range: 18.5mm
- Detent Function Range: 13.3mm
- Connectivity: RJ11, USB Type-B
Produktbrugsvejledning
Tilslutning til pc
Direkte forbindelse til pc
- Use the included USB cable to connect the Type-B end to the corresponding port on the back of the MOZA MTQ Throttle Quadrant, and the Type-A end to your PC.
- If connected successfully, the device’s light will gradually illuminate, and the MOZA Cockpit will indicate that the device is connected.
- If the device fails to light up, check whether the light brightness is turned off in the MOZA Cockpit.
Tilslutning til pc via MOZA Flight Base
- Connect one end of the included RJ11 cable to the corresponding port on the MOZA MTQ Throttle Quadrant and the other end to the MOZA Flight Base.
- Power on the base; if connected successfully, the device light will illuminate, and the MOZA Cockpit will indicate that the device is connected.
Adjusting Sliding Friction
To adjust the sliding friction of the levers, use the included wrench to turn the screw clockwise to increase or counterclockwise to decrease.
Replacing the Throttle Levers
Loosen the Fixing Screw
Use the provided wrench to loosen the fixing screw at the indicated position.
Remove the Existing Levers
Once the screw is loosened, gently pull out the existing throttle levers.
Install the New Lever Module
Align the new throttle lever module with the connecting rod, then insert it fully until it is secure without wobbling.
Secure the New Levers
Using the provided wrench and screwdriver, tighten the screw at the indicated position to ensure the new lever module is firmly secured in place.
Note: TQA and TQB need to be purchased separately.
Hurtig guide
Parametre
User Guide Connecting to PC
- Direkte forbindelse til pc
Use the included USB cable to connect the Type-B end to the corresponding port on the back of the MOZA MTQ Throttle Quadrant, and the Type-A end to your PC. If connected successfully, the device’s light will gradually illuminate, and the MOZA Cockpit will indicate that the device is connected.- If the device fails to light up, check whether the light brightness is turned off in the MOZA Cockpit.
- User Guide Connecting to PC
- Direkte forbindelse til pc
- Use the included USB cable to connect the Type-B end to the corresponding port on the back of the MOZA MTQ Throttle Quadrant, and the Type-A end to your PC. If connected successfully, the device’s light will gradually illuminate, and the MOZA Cockpit will indicate that the device is connected.
- If the device fails to light up, check whether the light brightness is turned off in the MOZA Cockpit.
- Tilslutning til pc via MOZA Flight Base
Connect one end of the included RJ11 cable to the corresponding port on the MOZA MTQ Throttle Quadrant and the other end to the MOZA Flight Base. Power on the base; if connected successfully, the device light will illuminate. and the MOZA Cockpit will indicate that the device is connected.
- Direkte forbindelse til pc
Adjusting Sliding Friction
To adjust the sliding friction of the levers, use the included wrench to turn the screw clockwise to increase or counterclockwise to decrease.
Replacing the Throttle Levers
To replace the throttle levers, follow these steps:
- Loosen the Fixing Screw
Use the provided wrench to loosen the fixing screw at the indicated position. - Remove the Existing Levers
Once the screw is loosened, gently pull out the existing throttle levers. - Install the New Lever Module
Align the new throttle lever module with the connecting rod, then insert it fully until it is secure without wobbling. - Secure the New Levers
Using the provided wrench and screwdriver, tighten the screw at the indicated position to ensure the new lever module is firmly secured in place.
Note: TQA and TQB need to be purchased separately.
Software introduktion
Panelindstillinger
When the throttle levers are replaced, the right-side diagram automatically updates to match the new layout and inputs.
Aksekalibrering
The throttle quadrant sticks are factory-calibrated and ready for immediate use. If you notice a mismatch between the physical movement of the sticks on the TQF and the corresponding axis output, you may need to perform axis calibration.
To begin calibration:
- Click the “Start Calibration” button.
- Follow the on-screen instructions. Before the countdown ends, move all sticks (throttle, flap, and speedbrake) back and forth through their full range of motion.
- Once calibration is complete, the sticks will function properly.
Axis Detent Function
- This feature maps throttle travel to game input with precision and defines Cutoff, Idle, and Afterburner zones.
- Users can calibrate detent positions via the settings window; six virtual buttons will be added for mapping each zone. The Axis Output panel shows logical axis values (top) and physical travel percentage (bottom) for easy alignment and feedback.
Speedbrake and Flap Axis Mapping Modes
The speedbrake and flap levers support three modes:
- Button Mode: Outputs only button signals, no axis data.
- Axis Mode: Outputs raw analog axis values.
Button Light Lighting Control Modes
Lighting control modes determine how the software manages the button lighting. Users can choose between two modes:
- Device Mode: Button lighting responds dynamically to input from a selected control axis (e.g., the speedbrake axis). As the axis value changes (e.g., the speedbrake axis value increases), the lights react according to the selected lighting pattern.
- Manual Mode: Manually adjust the button lighting using the brightness slider and lighting effect dropdown in the software interface.
Knapbelysning og -effekter
This device supports customizable backlighting and lighting effects. Users can configure lighting modes and colors via the Cockpit software to create a personal-ized visual experience.
Understøttede funktioner:
- Multiple lighting modes (Static, Blinking, Breathing)
- Button lighting feedback
- 16.7 million-color RGB customization
- Pattern and brightness adjustment
- Click the color swatch in the MOZA Cockpit interface to select your preferred lighting style and brightness.
Forholdsregler
- Udsæt ikke enheden for væsker eller fugt, da det kan forårsage brand eller elektrisk stød.
- Undgå at bruge enheden i direkte sollys.
- Brug ikke MOZA flysim-udstyr sammen med MOZA-racerudstyret.
- Anbefalet indendørstemperatur: 5°C ~ 35°C.
- For din sikkerhed og velvære skal du overvåge din spilletid og tage pauser efter behov.
- Enheden er ikke egnet til børn under 6 år, småt tilbehør kan udgøre en kvælningsfare!
- Børn under 13 år skal have voksenopsyn.
- Det er strengt forbudt at skille udstyret ad på egen hånd, manglende overholdelse af dette vil resultere i tab af garanti.
- Udstyret skal tilsluttes den fabriksleverede strømforsyning for at sikre den elektriske sikkerhed og beskyttelsen af brugerrettigheder og interesser.
- For at sikre brugersikkerheden må reparation eller udskiftning af dele kun udføres af officielt autoriserede reparationscentre.
- Ikke-standard strømforsyninger er strengt forbudt, selvom data såsom relateret voltages match.
- Brug kun vekselstrøm fra en standard stikkontakt for at undgå beskadigelse af produktet.
- Udsæt ikke enheden for varmekilder.
- Tag enhedens netledning ud, hvis den ikke skal bruges i længere tid.
- Hvis du finder noget unormalt, skal du straks stoppe med at bruge det og søge hjælp fra MOZA-repræsentanter eller autoriserede reparationscentre.
- Hold øje med vores officielle webwebsted og sociale medieplatforme for de seneste produktopdateringer.
KONTAKTE
- Producent: Shenzhen Gudsen Technology Co., Ltd Adresse: Værelse 1903-1904, Bygning 3, Nanshan ZhiyuanChongwen Park, No. 3370 Liuxian Avenue, Nanshan District, Shenzhen Kina
- Web: www.mozaracing.com
- E-mail: info@mozaracing.com
- Fremstillet i Kina
- EU-repræsentant: Gudsen Technology EU GmbH Adresse: Birkenstrasse 23, 40233 Düsseldorf Kontakt: JUNWEN DING
- E-mail: support@gudsen.com
- Repræsentant i Storbritannien: Gudsen Technology UK Limited Adresse: Tc-Abo, Luminous House, 300 South Row Milton Keynes, MK9 2FR, Storbritannien Kontakt: JUNWEN DING
- E-mail: support@gudsen.com
Ofte stillede spørgsmål
Q: How can I calibrate detent positions for Axis Detent Function?
A: Users can calibrate detent positions via the settings window; six virtual buttons will be added for mapping each zone. The Axis Output panel shows logical axis values (top) and physical travel percentage (bottom) for easy alignment and feedback.
Q: What should I do if my device fails to light up when connected to a PC?
A: Check whether the light brightness is turned off in the MOZA Cockpit. If so, adjust the settings to enable the light.
Dokumenter/ressourcer
 |
MOZA RACING MTQ Throttle Quadrant [pdfBrugermanual MTQ Throttle Quadrant, Throttle Quadrant, Quadrant |