LTECH Mini Pro LED Dimmer Controller Kit Instruction Manual

LTECH Mini Pro LED Dimmer Controller Kit

LED Dimmer Controller Kit

• Compact and lightweight, with a housing made from
• Covestro/Samsung V0-rated flame-retardant PC material;
• Features a soft-start gradual dimming function for greater visual comfort;
• Uses a 2.4GHz RF wireless signal, eliminating the need for signal cables;
• Ultra-sensitive touch brightness ring for adjusting brightness;
• Includes a brightness shortcut function for one-touch switching between brightness levels;
• A single remote control can manage an unlimited number of controllers within its effective range;
• Controllers within the same group or zone feature dynamic synchronization;
• LED status indicators provide operational feedback.

Tekniske specifikationer

M1A+P1

• Fjernbetjening
  • M1A
• Produkt farve
  • Hvid
• Dæmpningstype
  • DIM
• Trådløs type
  • RF 2.4 GHz
• Operation Voltage
  • 3 VDC (1 CR2032 button cell battery)
• Standby-strøm
  • < 2UA
• Fjernbetjenings rækkevidde
  • 30 meters (under ideal conditions)
• Driftstemp
  • -25°C~50°C
• Produktets vægt
  • 40g+5g
• Dimensioner
  • 104×58×9mm (remote control) 108×63×14 mm (remote control+backrest)
• Controller
  • P1
• Input signal
  • RF2.4GHz
• Input bindtage
  • 12-48V
• Udgang Voltage
  • 12-48V
• Antal kanaler
  • 1 kanal
• Nulstil kontakt
  • Ja
• Belastningsstrøm
  • Maks. 11A
• Indlæs strøm
  • 132W@12 240W@24V 28W@36V 384W@48V
• Beskyttelse
  • Short-circuit, over-temperature, overcurrent, and reverse connection protection
• Produktets vægt
  • 46g+5g
• Dimensioner
  • L91×B37×H21(mm)

Produktdimensioner

• Enhed: mm

Produkt installation

To måder at fastgøre fjernbetjeningsholderen på:

1. Fastgør fjernbetjeningsholderen i væggen med to skruer.
2. Fix the remote holder in the wall with 3M adhesive.
   • Note: Træk venligst batteritappen ud før første brug

Udskiftning af batteri

1. Use a screwdriver to unscrew the bottom screw.
2. Pull out the battery compartment and replace the battery.
3. Tighten the screw after replacing the battery

Funktioner

• Magt: Tænder eller slukker lyset.
• Lysstyrke Touch Ring: Touch to change the light’s brightness.
• Lysstyrke +/-: Adjusts the brightness; short press for 11 levels; long press for 1-6 seconds for 255 levels of continuous adjustment.
• Lysstyrke Shortcut Key: 25%, 50%, 75%, 100%.
• Scene: Short press to recall a scene; long press for 2 seconds to save the current light state to the scene.

Ledningsdiagram

Parring

Knapparring

1. Briefly press the ID learning button on the controller. The load indicator will flash. Please complete the following steps within 10 seconds.
2. Mini Pro Series Single-Zone Remote Control with Pairing:
   • Press and hold the power button until the controller’s load indicator flashes rapidly and then stays lit, and the color ring changes when touched.
   • Programmeringen er færdig.

ID Learning Key

Power-on synchronization

1. After the controller has been powered off and then powered back on, please complete the following steps within 10 seconds.
2. Mini Pro Series Single-Zone Remote Control with Pairing:
   • Press and hold the power button until the controller’s load indicator flashes rapidly and then stays lit, and the color ring changes when touched.
   • Programmeringen er færdig.

Note: A single controller can pair with up to 10 remote controls. If more than 10 remote controls are paired, the ID code of the first remote control will be automatically deleted.

Ryd kode

How to delete all remote controls:

• Press and hold the “Learn” button on the controller for 6 seconds. The controller’s load indicator will flash quickly four times and then remain lit, indicating that the code has been successfully cleared.

ID Learning Key

Forholdsregler ved installation

• Please do not stack the products. The distance between two products should be> 15 cm so as not to affect heat dissipation and the lifespan of the products.
• Do not fix the product tightly against the wooden board with screws. Please add a washer ≥7 mm thick under the mounting screws to leave a gap for effective heat dissipation and to avoid affecting the heat dissipation and service life of the product.
• Do not allow the product to come into large-area contact with metal objects (e.g. keel frames). The separation distance shall be ≥15 cm to avoid signal interference affecting operation.
• Do not place the product on top of a power supply. The distance between the product and the power supply should be ≥15 cm so as not to affect heat dissipation and the lifespan of the product.
• Please do not place the products on the floor. The distance between the product and the floor should be> 100 cm to avoid signal interference.
• Please do not install the products on beams or near the corners. The distance between the product and the beam or the corner should be> 15 cm so as to avoid signal interference.

SIKKERHEDSINSTRUKTION

Opmærksomhed

• Produktinstallation og idriftsættelse skal udføres af en kvalificeret fagmand.
• Products are and not lightning proof non-waterproof (special models excepted). Please avoid the sun and rain. When installed outdoors, please ensure they are mounted in a waterproof enclosure or in an area equipped with lightning protection devices.
• God varmeafledning forlænger produktets levetid. Installer venligst produktet i et miljø med god ventilation.
• During installation, avoid being close to large-area metallic objects or stacking the devices to prevent signal interference from affecting the usage.
• Undgå installation i tordenvejrstruede områder, områder med stærke magnetfelter og områder med høj voluminøsitet.tage områder.
• Når du installerer dette produkt, skal du undgå at være i nærheden af ​​et stort område med metalgenstande eller stable dem for at forhindre signalinterferens.
• Kontroller venligst, om arbejdsvolumentagDen anvendte overholder produktets parameterkrav.
• Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger an accident.
• Hvis der opstår en fejl, skal du ikke forsøge at reparere produktet selv. Hvis du har spørgsmål, bedes du kontakte leverandøren.
• The contents of this manual are subject to change without prior notice. In case of any discrepancy between the description and actual functions, the physical product shall prevail. Please feel free to contact us.

Garantiaftale

• Warranty period from the date of delivery: 5 years.
• Gratis reparation eller udskiftning af kvalitetsproblemer leveres inden for garantiperioderne.

Garantiudelukkelser herunder:

• Ud over garantiperioder.
• Enhver kunstig skade forårsaget af høj voltage, overbelastning eller ukorrekt betjening.
• Produkter med alvorlig fysisk skade.
• Skader forårsaget af naturkatastrofer og force majeure.
• Garantietiketter og stregkoder er blevet beskadiget.
• No contract signed by our company.
  • Reparation eller udskiftning er den eneste retsmiddel for kunder. Vores virksomhed er ikke ansvarlig for hændelige skader eller følgeskader, medmindre det er inden for rammerne af loven.
  • Our company has the right to amend or adjust the terms of this warranty, and any release in written form shall prevail.