• Produkt: DD274B-controller
• Input bindtage: AC 100- 240V, 50- 60Hz
• Arbejdstemperatur: -10°C til +65°C
• Trådløs Reception
• Mekanisk Begrænse
• Forbindbar 12V 24W LED Strip
• Radiofrekvens: 433.92 MHz
• Radiorækkevidde: 200m udendørs, 35m indendørs
• Max. Channels: 20

Produktbrugsvejledning

Trådløs modtagelse og mekanisk grænse

• The DD274B controller allows wireless reception and features a mechanical limit to control the motor running time.

LED-strimmelforbindelse

• To connect a 12V 24W LED strip, use the provided wiring guide with the specified colors for positive, negative, and switch connections.

Parring af emittere

• To pair additional emitters, follow the specific instructions provided: press the UP and STOP buttons simultaneously for 2 seconds to pair, and ensure the setting indicator confirms successful pairing.

Skift roterende retning

• To switch the rotating direction, press the UP and DOWN buttons simultaneously for 6 seconds during the setting status. The setting indicator will confirm the successful direction switch.

Slet udledere

• To delete one or all additional emitters, follow the instructions provided while ensuring each operation is completed within 10 seconds to prevent exiting the setting status prematurely.

Jog funktion

• Activate the jog function by following the specific instructions; short-press UP or DOWN for jogging, running, or press and hold for more than 2 seconds for continuous movement.

Produktegenskaber

1. Note: The motor with this receiver can run continuously, Max. 3 minutes.
2. When the emitter is group-controlled, the code is invalid.

• Trådløs reception
• Lys røre
• Mekanisk begrænse
• Forbindbar 12V 24W LED strip
• Input voltage: AC 100~240V 50~ ~60Hz
• Arbejdstemperatur: – -10°C ~ +65°C
• One MB274 B controller can store a maximum of. 20 channels.
• If you add a new channel, first cover the second channel and then cover it in turn

Radio rækkevidde

Note: The effective radio distance will deviate due to the actual environment.

Matchbare emittere

Note: Up button + Stop button = Setting button.

Instructions Of Buttons

Note: Up button + Stop button = Setting button.

Ledningsføring

Bedste installationsafstand

1. The shortest distance between the controller and the ground is≥1.5m
2. The shortest distance between the controller and the roof is≥0.3m
3. The shortest distance between the controllers and the controller is≥0.2m

Parring/parring af ekstra sender

Note: During the setting status, every operation should be less then 10S, or else, it will exit the setting and back to original status.

Skift roterende retning

Note: During the setting status, every operation should be less than 10S, or else, it will exit the setting and back to the original status.

• Press the controller’s UP and DOWN buttons at the same time for 6 seconds, hold on
• Setting the indicator always on, then flashed and extinguished
• The direction has been switched successfully.

Slet én ekstra emitter

Note: During the setting status, every operation should be less than 10S, or else, it will exit the setting and back to the original status.

Slet alle yderligere udledere

Note: During the setting status, every operation should be less than 10S, or else, it will exit the setting and back to the original status.

• Press the controller’s STOP and DOWN buttons at the same time for 6 seconds, then hold on.
• Setting the indicator always on, then flashed and extinguished
• All emitters have been deleted successfully.

Jog funktion

• Note: During the setting status, every operation should be less then 10S, or else, it will exit the setting and back to original status.
• When the jog function is activated, short-press UP or DOWN, the motor will jog run; Press UP or DOWN for more than 2 seconds, the motor will continue to run

FCC-erklæring

RF-eksponeringserklæring

Dette udstyr overholder FCC-grænseværdierne for strålingseksponering, der er fastsat for et ukontrolleret miljø. Denne sender må ikke placeres sammen eller fungere sammen med nogen anden antenne eller sender.

FCC advarsel

This device complies with Part 15 of the FCC Rules. Operation is subject to theThe  following two conditions:

1. Denne enhed må ikke forårsage skadelig interferens,
2. Denne enhed skal acceptere enhver modtaget interferens, inklusive interferens, der kan forårsage uønsket drift.

Note: Dette udstyr er blevet testet og fundet i overensstemmelse med grænserne for en digital enhed i klasse B i henhold til del 15 af FCC-reglerne. Disse grænser er designet til at yde rimelig beskyttelse mod skadelig interferens i en boliginstallation. Dette udstyr genererer, bruger og kan udstråle radiofrekvensenergi, og hvis det ikke installeres og bruges i henhold til instruktionerne, kan det forårsage skadelig interferens i radiokommunikation. Der er dog ingen garanti for, at der ikke vil forekomme interferens i en bestemt installation. Antag, at dette udstyr forårsager skadelig interferens i radio- eller tv-modtagelse, hvilket kan bestemmes ved at slukke og tænde udstyret. I så fald opfordres brugeren til at forsøge at korrigere interferensen ved hjælp af en eller flere af følgende foranstaltninger:

• Drej eller flyt modtagerantennen.
• Øg afstanden mellem udstyret og modtageren.
• Tilslut udstyret til en stikkontakt på et andet kredsløb end det, som modtageren er tilsluttet.
• Kontakt forhandleren eller en erfaren radio/tv-tekniker for at få hjælp.

NOTE: Enhver ændring eller modifikation af denne enhed, der ikke udtrykkeligt er godkendt af den part, der er ansvarlig for overholdelse, kan annullere brugerens ret til at betjene udstyret.

Ofte stillede spørgsmål

• Q: Hvad er den maksimale driftstid for motoren med denne modtager?
  • A: The motor can run continuously for a maximum of 3 minutes.
• Q: Hvor mange kanaler kan én DD274B-controller gemme?
  • A: The controller can store up to 20 channels. When adding a new channel, ensure to cover the previous channels accordingly.
• Q: Hvad er den bedste installationsafstand for DD274B-controlleren?
  • A: The recommended installation distances are 1.5m from the ground, 0.3m from the roof, and 0.2m between controllers.