Deli T322D Split Comb Binding Machine
INDLEDNING
- Tak for købetasing the NO.T322D wire binding machine of Deli Company. The multiple functions and elegant design make the product applicable to individual use and department use.
- We believe that the rubber ring binding machine with complete functions will make your document binding have higher efciency.
- For at få dig til at bruge produktet korrekt og forhindre ulejligheden for dig og andre personer, bedes du læse denne vejledning omhyggeligt.
Produktets tilsyneladende struktur og navnene
- Håndtag
- Wire closer control
- Wire closing channel
- Punch selector
- Punching channel
- Punching margin control
- Locating block
- Trådholder
- Papirskrot boks
Wire Size and Punching Margin Guide
| Wire (mm/inch) | 6.4 mm 1/4" | 7.9 mm 5/16" | 9.5 mm 3/8" | 11.1 mm 7/16" | 12.7 mm 1/2" | 14.3 mm 9/16" | 16 mm 5/8" |
|---|---|---|---|---|---|---|---|
| Ark | 25 | 45 | 65 | 80 | 95 | 125 | 135 |
| Punching margin | 2 | 3 | 3 | 4 | 4 | 5 | 5 |
Brugsanvisning
- The machine is used for punching of paper and plastic sheets, and wire loops is used for loose-leaf binding. The machine can only be used for this purpose, and please use it according to the operation instructions.
- Inden udstansning af de originale materialer skal du huske at bruge affaldspapir til at teste om maskinen fungerer normalt.
- Tøm affaldsbeholderen med jævne mellemrum.
- Den øvre grænse for stansning er 20, og dette antal må ikke overskrides.
- Stansning
- Set the locating block at the desired position. Turn the knob counterclockwise to loosen. Turn it clockwise to fasten.
- Set the punching margin control according to the previous guide chart
- Pull out and disengage the proper punch selector when you punch an odd-size document. For A5 size(210mm) punching, pull out the No. 25 punch selector(- from left to right).
- Push paper into the punching channel. Pull the handle all the way down until it stops to punch completely through. Pull the handle up completely and remove punched paper.
- Indbinding
- Place wire loops onto the wire holder. Load punched inner sheets into the wire loops, then the front cover. Finally, flip over the back cover and put it into the wire loops.
- Set the wire closer control for the desired wire size.
- Remove the booklet from the wire holder. Hold the booklet and let the wire loops rest fully into the wire closing channel.
- Pull down the handle completely to close the wire. Return it to the full upright position. Remove the bound booklet.
- Correct result: The seam of the closed wires should be kept inside the booklet, not exposed outside.
- Stansning
Fejlfinding Guide
| Fejlfænomen | Fejlårsagsanalyse | Fejlfindingsmetode |
|---|---|---|
| It is hard to press the handle when paper punching. | There is paper scrap or other hard objects in the paper cutting port. The operation is beyond the punching capacity described in the instruction. | Take out the sundries with chipboard. Operate according to the requirements of the instruction. |
| Stansekantafstanden har et hældningsfænomen. | The two sides of the incoming paper are unbalanced. There is paper scrap or other hard objects in the paper cutting port. | The two sides of the incoming paper are unbalanced. Take out the sundries with chipboard. |
| Ufuldstændig papirstansning, eller papiret er svært at trække ud. | Antallet af stykker papir til stansning ad gangen er for stort. | Reduce the punching thickness of each time (based on the requirements of the instruction). |
| Papiret kan ikke nå bunden. | Papiret er ubrugeligt, og papirkanten ruller. | Smooth the paper and then re-operate. |
Produktparametre
- Maksimal stansetykkelse: 20 pcs of paper (80g – A4 paper)
- Binding edge distance: 2-5 mm
- Afstand mellem hullerne: 8.47 mm
- Bindende specifikation: A4 papir eller derunder
- Maksimal bindingstykkelse: 135 stk
- Nettovægt: 8.68 kg
- Enhedsstørrelse: 380 mm × 355 mm × 322 mm
GARANTIKORT
- Tak for dit køb af vores produkter. Kundernes interesser, der køber vores produkter, vil blive beskyttet.
- For any malfunction due to product quality problems. please contact authorized local dealers or service centers with this receipt and the warranty card.
Garantibetingelser:
- For produktfejl, der opstår under normale driftsforhold, skal vores virksomhed yde gratis reparation og udskiftning af reservedele inden for et år fra købsdatoen.
- Kunder er forpligtet til at fremvise dette garantikort og den originale købsfaktura til vores virksomhed efter anmodning om garantiservice.
- This warranty card shall be valid only after the following form is filled out in detail and affixed with the official seal of the dealer
- Der ydes ingen gratis reparationsservice i tilfælde af nogen af følgende omstændigheder:
- Udløb af garantiperioden:
- Damages caused by improper use. Maintenance or storage not in accordance with the requirements of the user manual;
- Fejl eller skade som følge af uautoriseret adskillelse, reparation eller modifikation;
- Fejl eller skade forårsaget af force majeure;
- Sliddele eller tilbehør.
- This warranty card is being delivered with the product; one card for one product.
- Opbevar venligst dette garantikort i korrekt stand for gratis garantiservice. Der er ingen erstatning, hvis den går tabt.
Dato for Køb: ____ Y ____ M ____ D
Denne kopi skal skæres langs den stiplede linje og opbevares af forhandleren.
Særlig erklæring
- Denne manual er blevet nøje og omhyggeligt kontrolleret og gentagetviewed, but there may still be spelling and technical omissions and errors. Such omissions and errors will be corrected in the new version of the manual without further notice.
- The copyright of this manual belongs to our company; no other unit or individual is allowed to modify it.
CERTIFIKAT
- Inspector:______________________
- Date of Manufacture:______________________
KUNDESERVICE
- DELI GROUP CO., LTD.
- 301 Xuxiake Ave. Ninghai County
- Ningbo 315600 Kina Fremstillet i Kina
- info@nbdeli.com
- www.deliworld.com
Dokumenter/ressourcer
 | T322D Split Comb Binding Machine |
Referencer
- Brugermanualmanual.tools
Published: July 24, 2026