cod m V1.2 ZigBee Coordinator Owner’s Manual

cod m V1.2 ZigBee Coordinator

Specifikationer

• Produkt: cod.m ZigBee Coordinator V1.2
• Model: Kunst. nr. 90810
• Forsyning Voltage: 5V USB-C, max 0.8W PoE 802.3af max 1W
• Omgivelsestemperatur: Velegnet til indendørs brug
• Beskyttelsesklasse: IP20
• Dimensioner: Housing 64 x 74 x 22mm
• Vægt: 48g incl. housing, without antenna
• Standarder: IEEE 802.3 LAN, IEEE 802.11 WLAN, IEEE 802.15.4 ZigBee, IEEE 802.2af Power over Ethernet

Funktioner

• CC2652P7 Texas Instruments multiprotocol2.4GHz radio module
• ZigBee 3.x, Z-Stack firmware (Koenkk)
• Compatible with zigbee2mqtt (z2m), Home Assistant (zha), ioBroker, etc. Automatic detection by Home Assistant (zha)
• Operation via LAN, Wi-Fi or USB
• PoE (802.3af) or USB-C powered Less than 1W power consumption
• ESP32 open source firmware (cod.m XZG fork) https://github.com/codm/czc-fw/
• CC2652P7 firmware update via web interface, device firmware update via web interface or USB-C (Auto-BSL)
• Role selectable via web interface: coordinator, router, thread border router (under development)
• 3D-printed case, can also be used for wall-mounting (CC-BY-NC-SA)
• 9cm external antenna, included
• Made in Germany, CE, RoHS, WEEE

Hardware

The flashing power LED (green) indicates that the device is ready for operation. When a connection has been established by the host application, the power LED (green) lights up continuously. When pairing of the ZigBee host application (zigbee2mqtt, zha, etc.) is switched on, the ZigBee LED (yellow) lights up. The button can be used to switch the operating mode between LAN/WLAN and USB. When USB mode is switched on, the mode LED lights up (red). When using WLAN, please follow the instructions at https://docs.codm.de/en/zigbee/coordinator/ USB power has priority over PoE power and can be plugged in at any time without interruption. The coordinator restarts when switching back to PoE.

Idriftsættelse

• Screw the supplied antenna onto the antenna connection.
• Connect the code.m ZigBee Coordinator (CZC) to the Ethernet and/or USB-C power supply unit. When using Power over Ethernet*, the USB power supply unit is not required.
• When the green LED flashes, the coordinator is ready for operation.
• Read the DHCP IP in the router and access it via the browser: http://192.168.xx.xx/. Alternatively, use mDNS and access the coordinator at http://czc-xxxx.local. The host name can be found on the product sticker on the back of the housing.
• No further configuration is required for operation. Individual settings and operating modes can be made in the web operating modes can be made in the web interface.
  * only in PoE version

Konfiguration

• https://lnk.codm.de/zigbee-90810-setup-z2m-en
• https://lnk.codm.de/zigbee-90810-setup-iob-en
• https://lnk.codm.de/zigbee-90810-setup-ha-en

Tiltænkt brug

This cod.The ZigBee Coordinator (CZC) module is intended to provide a ZigBee interface (coordinator) via Ethernet, WLAN or USB. Only the specified intended use is permitted. Any other use will invalidate the warranty and liability.

Noter

Hereby, cod.m GmbH declares that the radio equipment type cod.m ZigBee Coordinator V1.2 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://lnk.codm.de/zigbee-90810-ce Keep the module away from heat and sunlight. Avoid contact with dust and the influence of liquids. Only use the module indoors. Protect the module from electrostatic discharge.

Tekniske data

Kontakte

• cod.m GmbH
• Allendorfer Straße 56
• 35708 Haiger
• Managing Director: Patrik Mayer
• Local Court Wetzlar, HRB 6686
• +49 2773 91878-0
• https://www.codm.de
• https://shop.codm.de
• UST-ID: DE815516311
• WEEE-Reg.-Nr.: DE78677954
• Støtte via support@codm.de, no telephone support!

Ofte stillede spørgsmål