Cdtech TP300 Bluetooth Module Owner’s Manual

Cdtech TP300 Bluetooth Module

Overview
CDI-WC46600A-01 is a Wi-Fi + BLE module independently developed by Cdtech based on the ECR6600-ATS2L chip. ECR6600-ATS2L is a SoC chip designed for smart home IoT terminal devices, supporting Wi-Fi 802.11b/g/n/ax and BLE 5.1 protocols. It includes a power management module, power amplifier, støjsvag amplifier, and transceiver switch. ECR6600-ATS2L adopts a RISC processor architecture, has ample storage space, rich peripheral interfaces, a more secure encryption mechanism, an on-chip FullMAC architecture, and a wider operating temperature range.

Karakteristika

Wi-Fi funktioner

• Supports IEEE 802.11 b/g/n/ax
• Understøtter fuld MAC, inklusive LMAC og UMAC
• Supports SoftAP, STA, and Wi-Fi direct connection mode
• Supports WMM QoS
• Supports 0.8/1.6/3.2 US security protection intervals
• Supports 802.11 ax MCS0 – MCS7
• The maximum bit rate reaches 150 Mbps
• Both uplink and downlink support MU-OFDMA (STA is supported)
• STA supports beamforming (STA acts as the Beamformer)
• Understøtter Mid-amble
• Supports 20 M and 40 M bandwidth. 802.11ax only supports 20 M bandwidth.
• Supports dual carrier modulation (Dual Carrier Modulation, DCM)

BLE funktion

• Supports BLE 5.1 protocol (does not support AOA/AOD)
• Supports single-device BLE connection
• Supports synchronous broadcasting and scanning
• Supports enhanced power control
• Output power up to +8 dBm
• Supports adaptive frequency hopping (AFH)
• Understøtter asynkron afsendelse og modtagelse af data
• Supports connection parameter update
• Supports extensible data packet length
• Understøtter linklagskryptering
• Understøtter LE ping

The Wi-Fi subsystem and BLE subsystem share the radio part, including ADC/DAC/PLL. Wi-Fi and BLE can only have one working at a time.

Generel specifikation

Pin description and PCBA size

Note: Method for downloading the module: VCC, GND, EN (pull-up), UART0_TX, UART0_RX, RESET_B (connected to the RTS of the serial port)

Module physical picture

Stykliste

Elektriske egenskaber

Direct-current characteristic

Suggested working conditions

Reflow soldering curve graph

Henviser til IPC/JEDEC-standarden.

• Toptemperatur: <250°C
• Antal gange: ≤2 gange

package figure

Pakningsinstruktioner

1. 700 stk

   • Each reel is loaded with 700 pcs (leave 20 empty pockets at both the front and back without components).

2. Perform vacuum packaging once the taping process is complete.

3. After vacuum packaging, place the taped reel into the inner box (700 pcs total per box).

4. 700pcs × 5 = 3500pcs

   • Each outer carton holds 5 inner boxes, for a total capacity of: $700\text{ pcs} \times 5 = 3500\text{ pcs}$.

WC46600A-01 is an ESD (Electrostatic Discharge) sensitive component. ESD or peak voltage may cause damage to the device. Although the WC46600A-01 has an internal ESD protection circuit, please handle it with care to avoid causing permanent damage or performance degradation.

Certificering
Integrationsvejledning til værtsproduktproducenter i henhold til KDB 996369 D03 OEM Manual v01r01

Liste over gældende FCC-regler
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter.

Specifikke driftsbetingelser
Antenna Placement Within the Host Platform The module is tested for mobile RF exposure use condition.. The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for exampved visse bærbare konfigurationer eller samplacering med en anden sender), anses FCC-godkendelsen ikke længere for at være gyldig, og FCC-id'et kan ikke bruges på det endelige produkt. Under disse omstændigheder vil OEM-integratoren være ansvarlig for at revurdere slutproduktet (inklusive transmitteren) og opnå en separat FCC-autorisation.

Begrænsede modulprocedurer
Ikke relevant

Spor antennedesign
Ikke relevant

Overvejelser om RF-eksponering
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

Antennetype og forstærkning

• Følgende antenner er blevet certificeret til brug med dette modul.
• Kun antenner af samme type med samme eller lavere forstærkning må også bruges med dette modul.
• Andre typer antenner og/eller antenner med højere forstærkning kan kræve yderligere autorisation til drift.

Oplysninger om overensstemmelse med slutproduktmærkning
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:“Contains FCC ID:2AATP-TP300”. The FCC ID can be used only when all FCC compliance requirements are met.

Oplysninger om testtilstande og yderligere testkrav
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirements, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Yderligere test, del 15 Subpart B Ansvarsfraskrivelse
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rules requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

Manuel information til slutbrugeren
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation, and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules

Sådan foretager du ændringer – Vigtig bemærkning
Hvis disse betingelser ikke kan opfyldes (famp(f.eks. visse bærbare computerkonfigurationer eller samlokalisering med en anden transmitter), anses FCC-godkendelsen ikke længere for at være gyldig, og FCC-ID'et kan ikke bruges på det endelige produkt. Under disse omstændigheder vil OEM-integratoren være ansvarlig for at revurdere slutproduktet (inklusive transmitteren) og indhente en separat FCC-godkendelse.

FCC-erklæring

Denne enhed er kun beregnet til OEM-integratorer under følgende forhold

1. The antenna must be installed such that 20 cm is maintained between the antenna and the user.
2. Sendermodulet må ikke placeres sammen med nogen anden sender eller antenne.

• Module Antenna Type: 2.4GHz onboard FPC Antenna, 2.68 dBi peak gain.

Denne enhed overholder del 15 af FCC-reglerne. Driften er underlagt følgende to betingelser:

1. Denne enhed må ikke forårsage skadelig interferens.
2. Denne enhed skal acceptere enhver modtaget interferens, inklusive interferens, der kan forårsage uønsket drift.

Bemærk: Bevillingshaveren er ikke ansvarlig for ændringer eller ændringer, der ikke udtrykkeligt er godkendt af den part, der er ansvarlig for overholdelse. Sådanne ændringer kan annullere brugerens tilladelse til at betjene udstyret.

BEMÆRK: Dette udstyr er blevet testet og fundet i overensstemmelse med grænserne for en Klasse B digital enhed i henhold til del 15 af FCC-reglerne. Disse grænser er designet til at give rimelig beskyttelse mod skadelig interferens i en boliginstallation. Dette udstyr genererer anvendelser og kan udstråle radiofrekvensenergi og kan, hvis det ikke installeres og bruges i overensstemmelse med instruktionerne, forårsage skadelig interferens på radiokommunikation. Der er dog ingen garanti for, at der ikke vil forekomme interferens i en bestemt installation. Hvis dette udstyr forårsager skadelig interferens på radio- eller tv-modtagelse, hvilket kan fastslås ved at slukke og tænde for udstyret, opfordres brugeren til at forsøge at korrigere interferensen ved hjælp af en eller flere af følgende foranstaltninger:

• Drej eller flyt modtagerantennen.
• Øg afstanden mellem udstyret og modtageren.
• Tilslut udstyret til en stikkontakt på et andet kredsløb end det, som modtageren er tilsluttet.
• Kontakt forhandleren eller en erfaren radio/tv-tekniker for at få hjælp.

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule, such as FCC Part 15 Subpart B, before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

RF-eksponeringserklæring
Dette udstyr overholder FCC's grænser for strålingseksponering, der er fastsat for et ukontrolleret miljø. Dette udstyr skal installeres og betjenes med en minimumsafstand på 20 cm mellem radiatoren og din krop