Electrolux 1.5 gallon minitank elektrisk vandvarmer brugsanvisning

Indledning

This manual provides essential information for the safe installation, operation, and maintenance of your Electrolux 1.5 Gallon Mini Tank Electric Water Heater. Please read this manual thoroughly before installation and use, and retain it for future reference.

Vigtige sikkerhedsoplysninger

ADVARSEL:

• Do not place the product in a basin or any location where it could be submerged in water.
• Sørg for korrekt jording for at forhindre elektrisk stød.
• Always shut off the power supply before performing any maintenance or service.
• Dette apparat skal installeres af en kvalificeret fagmand i overensstemmelse med alle lokale forskrifter og bestemmelser.
• Brug ikke vandvarmeren, hvis den er beskadiget eller ikke fungerer korrekt.

Hvad er der i æsken

Carefully unpack all components and ensure everything listed below is present and undamaged. If any items are missing or damaged, contact customer support.

• 1.5 Gallon Electric Tank Water Heater
• 3.6FT Plug Cord
• 3FT Drain Pipe
• Instruction Manual (English and French)
• Temperatur- og trykaflastningsventil
• Silicone Pads (3)
• Plastic Pagoda Fitting
• Teflon tape

Opsætning og installation

The following steps detail the installation process. It is recommended to watch the installation video for visual guidance.

Installationsvideoguide

1. Feet Installation

1. Remove the water heater from its packaging.
2. Locate the three support legs (silicone pads) included in the box.
3. Place the three support legs into the designated slots on the bottom liner of the water heater. Ensure they are securely seated.

2. Pressure Relief Valve Installation

1. Unpack the temperature and pressure (T&P) relief valve.
2. Wrap Teflon tape around the threaded openings of the T&P safety valve at least 15 times to ensure a watertight seal.
3. Install the T&P valve onto the designated port on the top of the water heater. Tighten securely with a wrench.

3. Pipe Connection Installation

1. Shut off the main cold water supply to the installation area.
2. Remove the existing cold water line fitting from your faucet. Pay attention to any pipe seals.
3. Install the provided three-way valve to the cold water line where the old fitting was removed. Ensure pipe seals are correctly in place.
4. Connect the water inlet pipe (blue hose) from the water heater to the three-way valve. Tighten securely.
5. Connect the faucet hot water connection pipe (red hose) to the hot water outlet fitting on the water heater. Tighten securely.
6. Attach the plastic pagoda fitting to the T&P relief valve.
7. Plug the drain hose (clear pipe) into the pagoda fitting.
8. Connect the other end of the drain hose to a suitable downspout or drain.

4. Initial Water Fill and Air Removal

1. Open the cold water valve to allow water to flow into the water heater.
2. Open the hot water faucet at the sink to fill the water heater with water and allow any trapped air to escape. Let the water run until a steady stream of water flows from the faucet, indicating all air has been purged.
3. Sluk for varmtvandshanen.

IMPORTANT: Ensure the water heater is completely filled with water and all air is exhausted before plugging in the power supply. Operating the unit dry will cause damage and void the warranty.

Betjeningsvejledning

1. Plug the water heater into a standard 120V (110V) outlet.
2. The temperature range for this unit is 55°F to 145°F.
3. To increase the water temperature, turn the control knob clockwise.
4. To decrease the water temperature, turn the control knob counter-clockwise.
5. If the indicator light does not come on, turn the control knob clockwise until it illuminates.
6. The indicator light will remain on while the water is heating and will turn off once the water temperature reaches the thermostat setting.
7. As soon as the water temperature in the tank drops below the thermostat setting, the light will come back on, indicating the unit is reheating.

Opretholdelse

Regelmæssig vedligeholdelse sikrer optimal ydeevne og levetid for din vandvarmer.

• Tøm og skyl: Periodically drain and flush the tank to remove sediment buildup, which can affect efficiency and tank life. Refer to the full instruction manual for detailed steps.
• Inspect T&P Valve: Annually inspect the Temperature and Pressure Relief Valve to ensure it is operating correctly.
• Rent ydre: Rengør ydersiden af ​​enheden med en blød, damp klæde. Brug ikke slibende rengøringsmidler.
• Glass-Lined Tank: The unit features a glass-lined tank designed to reduce scale adhesion, contributing to a longer service life.
• PUF Layer: The integrated PUF (Polyurethane Foam) layer helps lock in temperature, reducing heating frequency and saving energy.

Fejlfinding

If you encounter issues with your water heater, refer to the following common problems and solutions. For more complex issues, contact customer support.

• Intet varmt vand:
  • Check if the unit is plugged in and the power outlet is functional.
  • Ensure the temperature control knob is set to a desired temperature and not "Off".
  • Verify that the cold water supply valve is open.
  • Confirm the tank is full of water and all air has been purged.
• Vandet er ikke varmt nok:
  • Increase the temperature setting on the control knob.
  • Check if the unit is receiving adequate power.
• Lækker:
  • Inspect all pipe connections for tightness. Tighten if necessary.
  • Check the T&P relief valve for drips. If continuous, it may need inspection by a professional.

Specifikationer

Garanti og support

Your Electrolux 1.5 Gallon Mini Tank Electric Water Heater comes with the following warranty:

• Tankgaranti: 6 år
• Elektriske komponenters garanti: 2 år

For technical support, warranty claims, or to purchase replacement parts, please contact Electrolux customer service. Refer to the contact information provided in the full instruction manual or visit the official Electrolux webwebsted.