FOTING 12" Sand Filter Pump Instruction Manual

1. Sikkerhedsoplysninger

Please read and understand all safety warnings and instructions before installing, operating, or performing maintenance on this product. Failure to follow these instructions could result in serious injury or property damage.

• Denne pumpe er kun blevet evalueret til brug med vand. Må ikke anvendes med andre væsker.
• To reduce risk of electric shock, do not plug into power while standing on a wet or damp overflade.
• For at mindske risikoen for elektrisk stød må den kun tilsluttes en korrekt jordet stikkontakt.
• For at reducere risikoen for elektrisk stød, må du kun installere på et kredsløb, der er beskyttet af en jordfejlskredsløbsafbryder (GFCI).
• Always disconnect power before servicing the pump or filter system.
• Hold børn og uautoriserede personer væk fra pumpen og poolområdet under drift.

2. Produktet er slutview

The FOTING 12" Sand Filter Pump is designed to provide efficient and thorough filtration for above-ground pools up to 8000 gallons, ensuring crystal-clear water. It features a robust 1/2 HP motor and a versatile 6-way valve.

Image: The FOTING 12" Sand Filter Pump system, including the blue filter tank, black pump, pressure gauge, hoses, clamps, and filter balls.

Nøglefunktioner:

• Tilpasset filtrering: Choose from 10 time settings and single or continuous cycles for efficient operation.
• Maksimal gennemstrømningshastighed: Impressive 3000 GPH flow rate, ideal for pools up to 8000 gallons.
• Forbedret holdbarhed: Boasts a 44 lb sand capacity for long-lasting, efficient filtration.
• Enestående præstation: Equipped with a robust 1/2 HP motor and 27 ft maximum head for optimal water circulation.
• 6-vejs ventil: Kan tilpasses forskellige filtreringsbehov, hvilket sikrer et rent poolmiljø.

Komponenter inkluderet:

Image: A detailed diagram listing and illustrating the components included with the FOTING sand filter pump, along with its overall dimensions.

• Brugermanual
• Garantikort
• Trykmåler
• Afløbsstykke
• Par flange Clamps
• O-ring
• Unbrakonøgle
• NPT 1-1/2 hun-stik
• Forseglingstape
• Slange Clamps
• Sanddæksel
• Sylfonbælge
• Filtersamling
• Grundlag
• Ventilhovedsamling
• Cylinder
• Skruer & møtrikker

3. Opsætning

Proper setup is crucial for the optimal performance and longevity of your FOTING sand filter pump. Follow these steps carefully.

Monteringstrin:

1. Place the filter tank on a firm, level surface near your pool.
2. Install the pump onto the base, ensuring it is securely fastened.
3. Connect the pump to the filter tank using the provided hoses and clamps. Sørg for, at alle forbindelser er tætte for at forhindre lækager.
4. Attach the 6-way valve head assembly to the top of the filter tank.
5. Connect the pool hoses to the appropriate inlets and outlets on the pump and filter system.

Image: Illustration of the 1-1/2 inch pump hose connectors and hose adapters for connecting the filter system to an in/above ground pool.

Fyldning af filtertanken:

Before operating, the filter tank must be filled with the appropriate filter media. This model is designed for sand or filter balls.

• Ensure the drain plug is securely closed.
• Carefully add the recommended amount of filter sand (up to 44 lbs) or filter balls (200g included) into the tank.
• Overfyld ikke tanken.

Image: The FOTING sand filter pump highlighting its large flow rate of 3000 GPH, suitable for 2800-8000 gallon pools, with a 12-inch/44 lbs sand capacity and built-in timer.

4. Betjeningsvejledning

The FOTING sand filter pump features a 6-way valve for various functions and an intelligent timing system for automated operation.

6-Way Valve Functions:

The multi-port valve allows you to perform different operations by rotating the handle to the desired position. Always turn off the pump before changing valve positions.

Image: A visual guide to the 6-way valve, detailing each position and its corresponding function for pool water management.

1. FILTER: Normal filtering mode. Water passes through the filter media and returns to the pool.
2. TILBAGESKYLNING: Reverses water flow through the filter to clean the filter media. Water is discharged to waste.
3. SKYLLE: Used after backwashing to flush out any remaining debris from the filter and lines before returning to FILTER mode. Water is discharged to waste.
4. SPILD: Bypasses the filter and pumps water directly out of the pool to waste. Useful for lowering water level or vacuuming heavy debris.
5. LUKKET: Afbryder al flow til filteret og pumpen. Brug aldrig, mens pumpen kører.
6. RECIRKULER: Omgår filteret og cirkulerer vandet direkte tilbage til poolen. Nyttig til at blande kemikalier uden filtrering.

Intelligent Timing System:

The pump features a 24-hour dual-mode intelligent timing system, allowing you to set specific operating schedules.

Image: An illustration of the pump's control panel, detailing the two timing modes: Single Cycle Mode for a set duration and Continuous Cycle Mode for ongoing operation.

• Enkeltcyklustilstand: Set a specific duration for the pump to run (e.g., 8 hours). The pump will run for the set time and then turn off.
• Kontinuerlig cyklustilstand: The pump will run continuously until manually turned off or the timer is reset.
• Refer to the control panel (image below) for setting the timer.

Billede: Et nærbillede view of the FOTING pump's control panel, showing the digital display for time settings and the power and mode selection buttons.

5. Vedligeholdelse

Regular maintenance ensures the longevity and efficiency of your FOTING sand filter pump.

Bagskylning og skylning:

Backwash and rinse the filter regularly, especially when the pressure gauge reading increases by 5-10 PSI above its clean operating pressure, or when water flow to the pool decreases significantly.

• Sluk for pumpen.
• Set the 6-way valve to 'BACKWASH'.
• Tænd pumpen, og lad den køre, indtil vandet i skueglasset (hvis det er til stede) er klart (typisk 2-3 minutter).
• Sluk for pumpen.
• Set the 6-way valve to 'RINSE'.
• Turn on the pump and run for 30-60 seconds to flush the lines.
• Sluk for pumpen.
• Set the 6-way valve back to 'FILTER' for normal operation.

Billede: Et nærbillede view of the pressure gauge, which indicates the internal pressure of the filter system and helps determine when backwashing is needed.

Udskiftning af filtermedie:

Sand filter media typically needs replacement every 3-5 years, depending on usage and water quality. Filter balls may need cleaning or replacement more frequently based on their condition.

Image: A pyramid of white filter balls, indicating the type of filter media used in the system.

Vinterisering:

Before freezing temperatures, drain all water from the pump, filter, and hoses. Store the pump and filter in a dry, protected area to prevent freeze damage.

6. Fejlfinding

If you encounter issues with your FOTING sand filter pump, refer to the common problems and solutions below.

Image: A visual comparison demonstrating the powerful filtering ability of the pump, showing a pool's water clarity before and after filtration.

7. Specifikationer

Detailed technical specifications for the FOTING 12" Sand Filter Pump (Model FT-CLP5502).

Image: The FOTING sand filter pump highlighting its large flow rate of 3000 GPH, suitable for 2800-8000 gallon pools, with a 12-inch/44 lbs sand capacity and built-in timer.

8. Garanti og support

FOTING stands behind the quality of its products.

Garantioplysninger:

This FOTING sand filter pump is backed by a tre års garanti fra købsdatoen. Denne garanti dækker fabrikationsfejl og giver dig ro i sindet med hensyn til din investering.

Kundesupport:

For any questions, technical assistance, or warranty claims, please contact FOTING customer service. Refer to the warranty card included with your product for specific contact details or visit the official FOTING webwebsted.

We are committed to providing excellent after-sales support to ensure your satisfaction.