Jonard Tools CM-RJ45/8 RJ45 Kabelidentifikatorer til CM-100 Brugsanvisning

Indledning

This manual provides essential information for the proper use and maintenance of the Jonard Tools CM-RJ45/8 RJ45 Cable Identifiers. These identifiers are designed to work exclusively with the Jonard Tools CM-100 Cable Mapper Pro, facilitating efficient identification and mapping of RJ45 network cables.

Produkt overview

The CM-RJ45/8 kit includes eight (8) numbered RJ45 network cable identifiers. These identifiers are passive devices that, when connected to network cables, allow the CM-100 Cable Mapper Pro to distinguish between multiple cables connected to a patch panel or wall plate.

Nøglefunktioner:

Numbered Identification: Each identifier is clearly numbered from 1 to 8 for easy port mapping.
CM-100 Compatibility: Specifically designed to integrate with the Jonard Tools CM-100 Cable Mapper Pro.
Simultaneous Mapping: Enables mapping of up to 8 network cables concurrently.

Pack of 8 Jonard Tools RJ45 Cable Identifiers

Image: A set of eight numbered RJ45 cable identifiers, designed for use with the CM-100 Cable Mapper Pro.

Opsætning

Ensure CM-100 is Ready: Verify that your Jonard Tools CM-100 Cable Mapper Pro is powered on and functioning correctly. Refer to the CM-100 manual for its specific setup instructions.
Connect Identifiers: Plug each CM-RJ45/8 identifier into the RJ45 ports of the network cables you wish to map. For example, if you are mapping cables from a patch panel, connect one identifier to each cable's end at the patch panel.
Prepare Remote End: At the remote end of the cable run (e.g., wall plate), ensure the CM-100 Cable Mapper Pro is ready to receive the signal.

Jonard Tools RJ45 Cable Identifier plugged into a wall plate

Image: A numbered RJ45 cable identifier inserted into a network wall plate, demonstrating its application for port identification.

Betjeningsvejledning

Follow these steps to use the CM-RJ45/8 identifiers with your CM-100 Cable Mapper Pro:

Connect CM-100: Connect the main unit of the CM-100 Cable Mapper Pro to the network cable at the testing location (e.g., the switch end or the other end of the cable run).
Start test: On the CM-100, select the appropriate test mode for RJ45 cable mapping. The CM-100 will send a signal through the cable.
Identify Cable: The CM-100's display will show the identifier number corresponding to the cable it is connected to. This allows you to quickly match the remote end of the cable to its numbered identifier.
Repeat for All Cables: Repeat the process for each cable connected to an identifier until all desired cables are mapped.

Hand holding Jonard Tools CM-100 Cable Mapper Pro connected to a network cable in a server rack

Image: A technician using the CM-100 Cable Mapper Pro to test a network cable connected within a server rack, demonstrating cable mapping in a live environment.

Jonard Tools CM-100 Cable Mapper Pro connected to a network cable with an identifier

Image: The CM-100 Cable Mapper Pro connected to a network cable, with an RJ45 identifier visible, illustrating the compatibility and function of the system.

Opretholdelse

Rensning: Keep the identifiers clean and free from dust and debris. Use a soft, dry cloth for cleaning. Avoid abrasive cleaners or solvents.
Opbevaring: Store the identifiers in a cool, dry place, away from direct sunlight and extreme temperatures. Keep them in their original packaging or a protective case to prevent damage.
Inspektion: Periodically inspect the RJ45 connectors for any signs of wear, bent pins, or damage. Replace any damaged identifiers to ensure accurate testing.

Fejlfinding

Problem	Mulig årsag	Løsning
CM-100 does not detect identifier.	Identifier not fully inserted. Damaged identifier. Cable fault (open, short). CM-100 not in correct test mode.	Ensure identifier is securely seated in the RJ45 port. Try a different identifier. Test the cable for faults using the CM-100's primary functions. Verify the CM-100 is set to the correct mapping or identification mode.
Incorrect identifier number displayed.	Multiple identifiers connected to the same cable. Identifier malfunction.	Ensure only one identifier is connected to each cable being tested. Try a different identifier to confirm if the issue is with the identifier itself.

Specifikationer

Model: CM-RJ45/8
Kompatibilitet: Jonard Tools CM-100 Cable Mapper Pro
Connector Type: RJ45
Kabeltype: Ethernet
Number of Identifiers: 8 (numbered 1-8)
Dimensions (per identifier): Cirka 1.5 x 0.75 x 1.5 tommer
Vægt (samlet sæt): Cirka 0.81 ounce
Farve: Clear with blue accents

Garanti og support

For information regarding warranty coverage, technical support, or replacement parts for your Jonard Tools CM-RJ45/8 RJ45 Cable Identifiers, please refer to the documentation provided with your CM-100 Cable Mapper Pro or visit the official Jonard Tools website. Specific warranty details for this accessory are typically covered under the main CM-100 product warranty.

Officiel Webwebsted: www.jonard.com

	CTV-8K multifunktions kabel-tv-tester brugsanvisning \| Jonard Tools Omfattende instruktionsmanual til Jonard Tools CTV-8K multifunktionskabel-tv-tester, der beskriver dens funktioner, betjening, specifikationer og sikkerhedsoplysninger til installatører og teknikere.
	Jonard Tools CTV-8K multifunktions kabel-tv-tester brugsanvisning Omfattende instruktionsmanual til Jonard Tools CTV-8K multifunktionskabel-tv-tester, der beskriver dens funktioner, betjening og specifikationer for IP-kameratestning, netværksdiagnostik og kabelanalyse.
	Jonard Tools CTV-8K multifunktions kabel-tv-tester brugsanvisning Comprehensive instruction manual for the Jonard Tools CTV-8K Multifunction Cable TV Tester. This guide details its features, operation, safety precautions, and specifications for testing IP, Analog, and HD Coaxial cameras, along with PoE, HDMI, and various network diagnostic functions.
	Jonard Tools FPM-55 Optisk Effektmåler Brugsanvisning Omfattende instruktionsmanual til Jonard Tools FPM-55 optisk effektmåler, med detaljerede oplysninger om funktioner, specifikationer, betjening, nøglefunktioner, fejlfindingsvejledning og garantioplysninger.
	Jonard Tools mellemspændte slids- og ringværktøjer datablad - MS-526, MS-446, MS-426, MS-326, MS-316, MS-306, MS-6, MS-26, MS-336 Detaljeret datablad for Jonard Tools' patenterede Mid Span Slit & Ring Tools, designet til effektiv og sikker adgang til fiberoptiske kabler. Indeholder specifikationer, brugsanvisninger og reservedele til modellerne MS-526, MS-446, MS-426, MS-326, MS-316, MS-306, MS-6, MS-26, MS-336 og MS-600.
	Jonard Tools Universal Stripping Tool - Cable Stripping Guide Comprehensive instructions for the Jonard Tools Universal Stripping Tool (UST Series), covering coax, networking, and flat cable stripping with detailed steps and operational guidance.