ENJOYWOOD 60 x 22 Inch Heavy Duty Rubberwood Work Bench with Shelf Bracket and Drawer Instruction Manual

Indledning

This manual provides detailed instructions for the assembly, operation, and maintenance of your ENJOYWOOD 60 x 22 Inch Heavy Duty Rubberwood Work Bench. Please read this manual thoroughly before assembly and use to ensure safe and efficient operation.

Image: The ENJOYWOOD 60 x 22 Inch Heavy Duty Rubberwood Work Bench, featuring a natural wood top, black steel frame, an under-table drawer, and a wall-mounted shelf.

Sikkerhedsoplysninger

Adhering to safety guidelines is crucial for preventing injury and damage. Always follow these instructions:

• Læs alle instruktioner inden montering og brug.
• Ensure all components are securely fastened before applying weight to the workbench.
• Do not exceed the maximum load capacity of 2000 lbs for the main tabletop and 50 lbs for the shelf bracket.
• Use appropriate personal protective equipment (PPE) when working with tools on the bench.
• Hold arbejdsområdet rent og godt oplyst.
• Do not modify the workbench structure or components.
• Ensure the power outlets are properly grounded and used with compatible tools. Disconnect power when not in use.
• Adjust the workbench height only when clear of obstructions and without heavy loads.

Pakkens indhold

Kontroller, at alle dele er til stede, før monteringen påbegyndes. Hvis der mangler eller er beskadigede dele, skal du kontakte kundesupport.

• Rubberwood Tabletop (1)
• Steel Leg Frames (2 sets)
• Crossbar Supports (2)
• Adjustable Metal Feet (4)
• Under-table Drawer Assembly (1)
• Wall-mounted Shelf Bracket (1)
• Power Outlet Strip with Switch (1)
• Cord Organizer (1)
• Assembly Hardware (bolts, nuts, screws, washers, Allen key)
• Instruktionsmanual (dette dokument)

Monteringsvejledning

Assembly typically requires a 5mm Allen key (included), a Phillips head screwdriver, and a wrench. It is recommended to have a second person for easier assembly, especially when handling the tabletop.

Step 1: Assemble the Leg Frames

1. Attach the crossbar supports to the H-shaped steel legs using the provided bolts and Allen key. Ensure all connections are finger-tight at this stage.
2. Insert the adjustable metal feet into the bottom of each leg. Tighten them securely with a wrench.

Image: Detail of the stable H-shaped legs and 1.2mm thick steel construction, illustrating the robust frame components.

Image: Close-up of the adjustable metal feet, showing the threaded adjustment mechanism and anti-slip rubber pad for stability on uneven surfaces.

Step 2: Attach the Tabletop

3. Carefully place the rubberwood tabletop upside down on a soft, protected surface to prevent scratches.
4. Position the assembled leg frames onto the pre-drilled holes on the underside of the tabletop.
5. Secure the leg frames to the tabletop using the provided screws and a Phillips head screwdriver. Ensure all screws are tightened evenly.

Image: The rubberwood tabletop and steel frame components laid out, showing pre-drilled holes for easy assembly.

Step 3: Install the Drawer and Power Outlets

6. Slide the under-table drawer assembly into its designated position beneath the tabletop. Secure it using the provided hardware.
7. Attach the power outlet strip to the side of the workbench frame using the provided screws. Ensure the cord organizer is also attached if desired.

Billede: Et nærbillede view of the under-table drawer, open and containing various hand tools, demonstrating its storage capacity.

Image: The ETL-certified power outlet strip with multiple AC outlets and a red on/off switch, installed on the side of the workbench frame.

Step 4: Mount the Shelf Bracket

8. Determine the desired height and location for the wall-mounted shelf bracket above the workbench.
9. Mark the drilling points on the wall. Ensure the shelf is level.
10. Drill pilot holes and secure the shelf bracket to the wall using appropriate wall anchors and screws (not included, as wall types vary).
11. Place the shelf board onto the installed brackets.

Image: A wall-mounted shelf made of rubberwood, supported by black metal brackets, holding various hand tools.

Once all components are assembled, carefully turn the workbench upright. Double-check all connections for tightness before use.

Opsætning og justering

Adjusting Workbench Height

The workbench features adjustable legs to customize its height from 28 inches to 40 inches.

1. Ensure the workbench is empty and clear of any heavy items.
2. Locate the adjustment pins on each leg.
3. Press the pin and slide the inner leg section up or down to the desired height. Ensure the pin locks securely into one of the pre-drilled holes.
4. Repeat for all four legs, ensuring they are set to the same height for a level work surface.

Image: Diagram illustrating the adjustable height range of the workbench (28-40 inches) and overall dimensions, including the wall-mounted shelf.

Leveling the Workbench

The adjustable metal feet allow for leveling on uneven floors.

1. Place a spirit level on the tabletop to check for levelness.
2. Rotate the base of each adjustable foot clockwise to raise or counter-clockwise to lower, until the workbench is stable and level.

Betjeningsvejledning

Using the Work Surface

The 30mm solid rubberwood tabletop is designed to support up to 2000 lbs. It is suitable for various tasks including woodworking, repairs, and general crafting. Always distribute weight evenly across the surface.

Billede: Et nærbillede view of the rubberwood tabletop, highlighting its natural grain and smooth finish, indicating its durability and quality.

Brug af lagringsfunktioner

• Under-table Drawer: Use the spacious drawer for organizing smaller tools, hardware, and accessories. The drawer slides smoothly for easy access.
• Wall-mounted Shelf: The shelf provides additional storage for frequently used items or lighter tools, with a capacity of 50 lbs.
• Pegboard (if applicable): Some models may include dual-sided pegboards for hanging tools. Utilize standard pegboard hooks (not included) for convenient tool access.

Image: The workbench showcasing its multi-storage capabilities, including the wall-mounted shelf, integrated pegboard, and under-table drawer, all designed for efficient organization.

Brug af stikkontakterne

The integrated ETL-certified power outlet strip provides convenient access to power for your tools.

1. Plug the workbench's power cord into a grounded electrical outlet.
2. Press the red on/off switch to activate the outlets.
3. Plug your power tools or other devices into the AC outlets.
4. Always turn off the switch and unplug the workbench when not in use.
5. Use the cord organizers to keep cables tidy and prevent tripping hazards.

Image: A close-up of the workbench's side, showing the integrated power outlets with an on/off switch and a cord organizer, providing convenient access for power tools.

Opretholdelse

• Rensning: Wipe down the rubberwood tabletop with a damp cloth and mild soap. Avoid harsh chemicals that may damage the protective varnish. Clean the steel frame with a damp klæde.
• Inspektion: Regularly check all bolts and screws for tightness. Re-tighten as necessary to maintain stability.
• Træpleje: The rubberwood tabletop has a protective varnish. To prolong its life, avoid prolonged exposure to moisture and extreme temperatures.
• Elektriske komponenter: Inspect the power cord and outlets for any signs of damage. Do not use if damaged.

Fejlfinding

Specifikationer

Image: An illustration detailing the rugged construction of the workbench, highlighting the 1.2-inch rubberwood top, 50x50mm steel legs, anti-slip rubber pads, and load capacities for the tabletop (2000 lbs) and shelf (50 lbs).

Kundesupport

For any questions, missing parts, or assistance, please contact ENJOYWOOD customer support. You can find more information and contact details on the official ENJOYWOOD store page:

Visit the ENJOYWOOD Store