1. Introduktion
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Beninca Bull 424 FC Sliding Gate Opener. This chain-driven automation system is designed for residential sliding gates, supporting gates up to 800 lbs and 20 feet in length. Please read this manual thoroughly before proceeding with installation or operation.
Billede 1.1: Overview of the Beninca Bull 424 FC Sliding Gate Opener kit, showing the main motor unit, control panel, two remote controls, and a set of safety photocells.
2. Sikkerhedsoplysninger
WARNING: Improper installation or use can cause serious injury or death. Always follow all safety instructions.
- Sørg for, at alle elektriske tilslutninger udføres af en kvalificeret elektriker, og at de overholder lokale el-forskrifter.
- Hold hænder, fødder og tøj væk fra porten og åbnermekanismen under drift.
- Lad ikke børn lege med eller betjene portåbnerens betjeningselementer.
- Inspicer regelmæssigt porten og åbneren for tegn på slid, skader eller forkert justering.
- The photocell safety devices must be installed and maintained correctly to prevent entrapment.
- Afbryd strømmen, før der udføres vedligeholdelse eller reparationer.
3. Pakkens indhold
Bekræft, at alle nedenstående komponenter er til stede i din pakke:
- Beninca Bull 424 FC motor base
- Control panel with built-in receiver
- 20 ft chain for sliding gates
- Two (2) TO.GO 2A garage opener remote controls
- Beninca PUPILLA.T true beam photocell set
- Installation hardware (bolts, screws, etc. - specific items may vary)
4. Opsætning og installation
This section outlines the general steps for installing the Beninca Bull 424 FC. Refer to the detailed installation diagrams provided separately with your product for precise measurements and wiring instructions.
4.1 Forberedelse af stedet
Ensure the gate operates smoothly manually before installing the opener. The installation area for the motor base should be level and stable, capable of supporting the unit's weight (approximately 60 lbs).
4.2 Mounting the Motor Base
Securely mount the Beninca Bull 424 FC motor base to a concrete pad or suitable foundation. The unit dimensions are approximately 13 inches (W) x 10 inches (D) x 23 inches (H). Proper alignment with the gate's chain path is critical.
4.3 Kædeinstallation
Attach the provided 20 ft chain to the gate and route it through the motor's drive sprocket. Ensure the chain is taut but not overly tight, allowing for smooth movement without excessive friction. Adjust chain tension as needed.
4.4 Elektriske forbindelser
Connect the motor to the control panel and provide power according to the wiring diagram. The control panel has a built-in receiver. All electrical work must comply with local regulations and be performed by a certified professional.
4.5 Photocell Installation
Install the Beninca PUPILLA.T true beam photocell set on opposite sides of the gate opening. These safety devices detect obstructions in the gate's path, preventing closure and enhancing safety. Ensure they are aligned correctly for reliable operation.
5. Betjeningsvejledning
5.1 Parring af fjernbetjening
To pair the TO.GO 2A remote controls with the built-in receiver in the control panel, follow the specific programming instructions provided with the control panel documentation. Typically, this involves pressing a programming button on the control board and then a button on the remote.
5.2 Basic Gate Operation
Once paired, press a programmed button on the remote control to initiate gate movement. A single press will typically open or close the gate. Pressing again during movement will stop the gate. The system features adjustable speed settings for smooth movement.
5.3 Sikkerhedsfunktioner
The PUPILLA.T photocells will prevent the gate from closing if an obstruction is detected in its path. The gate will either stop or reverse direction, depending on the control panel's configuration. Test these safety features regularly.
6. Vedligeholdelse
Regular maintenance ensures the longevity and reliable operation of your gate opener. Perform these checks at least quarterly, or more frequently with heavy use.
- Clean the Motor Unit: Keep the motor housing free from dirt, debris, and insects.
- Smør kæden: Apply a suitable lubricant to the drive chain to ensure smooth operation and prevent rust.
- Inspect Photocell Lenses: Clean the lenses of the PUPILLA.T photocells to ensure clear beam transmission and reception.
- Tjek for forhindringer: Ensure the gate's path is clear of any obstacles that could impede movement.
- Test sikkerhedsfunktioner: Periodically test the photocells and any other safety edges or sensors to confirm they are functioning correctly.
- Undersøg ledninger: Check all electrical wiring for signs of wear, damage, or loose connections.
7. Fejlfinding
Dette afsnit omhandler almindelige problemer, du kan støde på. Hvis der er problemer, der ikke er nævnt her, eller hvis løsningerne ikke løser problemet, skal du kontakte kundesupport.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Porten bevæger sig ikke. | No power; remote not paired; safety device activated; motor overload. | Check power supply; re-pair remote; clear photocell path; allow motor to cool. |
| Porten stopper uventet. | Obstruction detected by photocells; gate friction; limit switch issue. | Clear obstruction; check gate for smooth manual movement; inspect limit switches. |
| Fjernbetjening virker ikke. | Dead battery; out of range; not paired correctly. | Replace battery; move closer to receiver; re-pair remote. |
| Porten bevæger sig langsomt eller med besvær. | Insufficient lubrication; gate friction; motor issue. | Lubricate chain and gate rollers; check gate alignment; consult technician. |
8. Specifikationer
| Feature | Detalje |
|---|---|
| Model | Beninca Bull 424 FC KIT |
| Portkapacitet | Up to 800 lbs (max tested), recommended 400 lbs for 16 ft gates |
| Portlængde | Op til 20 fod |
| Motortype | Chain-driven |
| Motorens drejningsmoment | 12 Nm |
| Fremstød | 336 N |
| Justerbar hastighed | 1 ft/sec (Z17) |
| Daily Cycles | Op til 200 cyklusser |
| Enhedsmål (B x D x H) | 13 cm x 10 cm x 23 cm |
| Varens vægt | 60 pund |
| Farve | Sort, Grå |
| Inkluderede komponenter | Motor base, Control panel with receiver, 20 ft chain, 2 TO.GO 2A Remotes, PUPILLA.T Photocell set |
9. Garanti og support
For product support, technical assistance, or warranty inquiries, please contact the seller or manufacturer directly. This product typically includes a 30-day easy return policy from the point of purchase. Retain your proof of purchase for all warranty claims.
For customer support, refer to the contact information provided by your retailer or visit the official BENINCA webwebsted.
