Feit Electric 20ft Chasing & Tunable White LED Tape Light User Manual

Vigtige sikkerhedsinstruktioner

ADVARSEL: FARE VED INDTAGELSE. Dette produkt indeholder en knapcelle eller et møntbatteri. DØD or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Indre kemiske forbrændinger på så lidt som 2 timer. Keep new and used batteries UDEN FOR RÆKKEVIDDE FOR BØRN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

• Always ensure the power adapter is disconnected from the power source before installation, maintenance, or troubleshooting.
• Do not expose the tape light or power adapter to excessive heat or direct flame.
• Do not submerge the tape light or power adapter in water. While designed for indoor/outdoor use, ensure connections are secure and protected from direct water exposure.
• Only use the provided power adapter and remote control with this product.
• Do not attempt to repair or modify the tape light or its components. Refer all servicing to qualified personnel.
• Sørg for, at monteringsfladen er ren, tør og glat for korrekt vedhæftning.
• Do not bend the tape light sharply or at angles less than 90 degrees to prevent damage to the LED circuits.
• Hold emballagemateriale væk fra børn.

Pakkens indhold

Bekræft, at alle komponenterne nedenfor er inkluderet i din pakke:

Figur 1: Pakkens indhold

• 1x Feit Electric 20ft Chasing & Tunable White LED Tape Light
• 1x fjernbetjening
• 1x strømadapter
• 10x monteringsclips
• 20 x skruer

Specifikationer

Detailed technical specifications for the Feit Electric LED Tape Light:

Figure 2: Product Features and Dimensions

Opsætningsvejledning

Follow these steps for proper installation of your LED Tape Light:

1. Planlæg dit layout: Before peeling the adhesive, unroll the tape light and lay it out in your desired location to confirm the length and placement. Ensure the power adapter can reach an outlet.
2. Forbered overfladen: Clean the installation surface thoroughly. It must be dry, smooth, and free of dust, dirt, or grease for optimal adhesive performance.
3. Cut to Size (Optional): If a shorter length is required, locate the designated cutting marks on the tape light (typically indicated by a scissor icon or copper pads). Cut only at these marked points to avoid damaging the circuit.
4. Apply the Tape Light: Carefully peel off the backing from the adhesive strip on the back of the tape light. Press the tape light firmly onto the prepared surface, working in small sections to ensure good contact and avoid air bubbles.
5. Fastgør med klips (valgfrit): For added security, especially on textured surfaces or in high-traffic areas, use the included mounting clips and screws. Space them evenly along the tape light.
6. Tilslut strøm: Plug the tape light connector into the power adapter. Then, plug the power adapter into a standard electrical outlet.
7. Link Multiple Strips (Optional): If linking multiple 20ft strips (up to a maximum of 40ft total), connect them end-to-end using the integrated connectors. Ensure the power supply is adequate for the total length.

Figur 3: Eksample Indoor Installation (Kitchen)

Figur 4: Eksample Outdoor Installation (Patio)

Betjeningsvejledning

Control your Feit Electric LED Tape Light using the included remote control:

Figure 5: Remote Control and Tape Light

• Tænd/sluk: Tryk på Power-knap (red button, top right) to turn the lights on or off.
• Justering af lysstyrke: Brug Lysstyrke op (▲) og Lysstyrke ned (▼) buttons to adjust the light intensity.
• Farvevalg:
  • Tryk på RGB color buttons (Red, Green, Blue, etc.) to select a static color.
  • Tryk på "W" button for Tunable White light.
• Dynamiske tilstande:
  • Chasing Effects: Brug "Chase" button to activate dynamic chasing light patterns.
  • Andre tilstande: Explore buttons like "Flash", "Strobe", "Fade", og "Smooth" for various light transitions and effects.
  • Hastighedstilpasning: Brug Sæt fart på og Hastighed ned buttons to control the pace of dynamic modes.
• Timer funktion: Some remotes may include a timer function. Refer to the remote's specific markings for details.

Figure 6: Kitchen with Red Light

Figure 7: Kitchen with Warm White Light

Figure 8: Kitchen with Cool White Light

Opretholdelse

To ensure the longevity and optimal performance of your LED Tape Light, follow these maintenance guidelines:

• Rensning: Frakobl strømadapteren før rengøring. Brug en blød, tør eller let fugtet klud.amp cloth to wipe the tape light. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the product.
• Inspektion: Periodically inspect the tape light and power adapter for any signs of damage, such as frayed wires, cracks, or loose connections. If any damage is found, discontinue use and contact customer support.
• Opbevaring: If storing the tape light for an extended period, ensure it is clean and dry. Coil it loosely to prevent kinks or damage to the LED strip. Store in a cool, dry place away from direct sunlight.
• Batteriudskiftning (fjernbetjening): If the remote control's range or responsiveness decreases, the battery may need replacement. Refer to the remote's battery compartment for the correct battery type (typically a CR2025 or similar coin cell battery) and replacement instructions. Ensure proper polarity.

Fejlfinding

If you encounter issues with your Feit Electric LED Tape Light, refer to the following common problems and solutions:

Garantioplysninger

Denne Feit Electric LED-båndlampe er dækket af en 1 års producentgaranti from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, abuse, accidents, unauthorized repairs, or modifications. Please retain your proof of purchase for warranty claims.

Kundesupport

For further assistance, technical support, or warranty inquiries, please contact Feit Electric customer support.

Visit our online support portal for FAQs and contact options:
https://help.feit.com/hc/en-us