FOTING 1.5 HK lavvandspumpe med tryktank, brugsanvisning, model JGP110037C

1. Introduktion

This manual provides comprehensive instructions for the safe and efficient installation, operation, and maintenance of your FOTING 1.5HP Shallow Well Pump with Pressure Tank, Model JGP110037C. This pump is designed for various water transfer and pressure boosting applications, including garden irrigation and domestic water supply. Please read this manual thoroughly before use and retain it for future reference.

FOTING 1.5HP Shallow Well Pump with Pressure Tank, front view.

Image 1: The FOTING 1.5HP Shallow Well Pump with its integrated pressure tank, pressure gauge, and electrical housing.

2. Vigtige sikkerhedsoplysninger

Overhold altid grundlæggende sikkerhedsforanstaltninger for at reducere risikoen for brand, elektrisk stød og personskade. Manglende overholdelse af disse instruktioner kan resultere i alvorlig personskade eller materielle skader.

Elektrisk sikkerhed: Sørg for, at strømforsyningen passer til pumpens volumentage (115V). Always connect to a grounded outlet. Do not operate with damaged cords or plugs. Disconnect power before servicing.
Vandsikkerhed: Do not pump flammable or corrosive liquids. Ensure the pump is not submerged unless specifically designed for submersible use. Protect the pump from freezing temperatures.
Personlig sikkerhed: Wear appropriate personal protective equipment (PPE) during installation and maintenance. Keep children and unauthorized persons away from the operating pump.
Installation: Install the pump on a stable, level surface. Ensure proper ventilation. Do not block air vents.
Operation: Never run the pump dry. Ensure the pump is properly primed before initial use.

3. Pakkens indhold

Kontroller, at alle genstande er til stede og ubeskadigede ved udpakning:

FOTING 1.5 hk lavvandspumpe med tryktank
Pressure Gauge (pre-installed)
Mechanical Pressure Switch (pre-installed)
2 x NPT 1" to GHT 3/4" Adapters
Instruktionsmanual

4. Specifikationer

Key technical details for the FOTING JGP110037C pump:

Mærke	FOTING
Modelnummer	JGP110037C
Hestekraft	1.5 HK
Voltage	115 volt
Max flowhastighed	1200 GPH (1340 GPH stated in some graphics)
Max løftehøjde	160-164 fod
Max sugehøjde	23 fod
Max tryk	4.5 Bar
Trykbeholderkapacitet	5 gallons
Indgang / udgangsstørrelse	1" NPT
Beskyttelsestype	IP54 (Water-Resistance)
Produktdimensioner	17 cm L x 10.5 cm B x 20 cm H
Varens vægt	35.7 pund

FOTING pump working performance chart with max suction and height-lift.

Image 2: Diagram illustrating the pump's working performance, showing maximum suction and varying flow rates at different height-lifts.

5. Opsætning

Korrekt installation er afgørende for pumpens ydeevne og levetid.

5.1 Udpakning og inspektion

Carefully remove the pump from its packaging. Inspect for any visible damage. If damage is found, do not proceed with installation and contact customer support.

5.2 Placering

Place the pump on a firm, level surface. Ensure the location is well-ventilated, protected from direct sunlight, rain, and freezing temperatures. The pump should be as close to the water source as possible to minimize suction lift.

5.3 Connecting Inlet and Outlet Pipes

Connect the inlet pipe (suction line) to the pump's intake port and the outlet pipe (discharge line) to the discharge port. Use appropriate NPT 1" fittings. The included NPT 1" to GHT 3/4" adapters can be used for garden hose connections if needed. Ensure all connections are tight and leak-free.

Diagram of FOTING Shallow Well Pump components.

Image 3: A detailed diagram highlighting key components of the pump, including the 1" NPT outlet and intake ports for pipe connections.

Three steps for easy pump use: connecting inlet, adding water for priming, and connecting outlet.

Image 4: This image illustrates the three primary steps for initial pump setup: connecting the inlet pipe, adding water for priming, and connecting the outlet pipe.

5.4 Spædning af pumpen

Before the first use, the pump must be primed. Remove the priming plug (usually located on top of the pump housing) and fill the pump casing completely with water. Replace the plug securely. This step is essential to ensure the pump can create suction and operate correctly.

Person pouring water into the pump for priming.

Billede 5: Et nærbillede view of a hand pouring water into the pump's priming port, a critical step before initial operation.

5.5 Elektrisk tilslutning

Connect the pump to a dedicated 115V, 60Hz grounded electrical outlet. Ensure the circuit is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety, especially in outdoor or wet environments.

6. Betjeningsvejledning

Once installed and primed, your FOTING pump is ready for operation.

6.1 Første opstart

After priming, turn on the power switch. The pump will start and begin to build pressure in the tank. Allow it to run until the pressure gauge reaches the upper cut-off pressure (approximately 3.0 bar), at which point the pump will automatically shut off.

6.2 Automatisk drift

The integrated pressure tank and mechanical pressure switch enable automatic operation. The pump is preset to start automatically when the pressure drops below 1.5 bar and shut off when it reaches 3.0 bar. This maintains consistent water pressure without constant manual intervention.

Close-up of FOTING pump's pressure gauge and mechanical pressure switch.

Image 6: This image provides a close-up view of the built-in pressure gauge for real-time pressure observation and the mechanical pressure switch, which controls automatic pump operation.

6.3 Overvågning af tryk

The built-in pressure gauge allows for real-time observation of the water pressure within the system. Regularly check the gauge to ensure the pump is operating within its normal pressure range.

6.4 Ansøgninger

This pump is suitable for a variety of applications:

Garden Watering: Provides consistent pressure for hoses and sprinklers.
Farm Irrigation: Can be integrated into agricultural irrigation systems.
Vandoverførsel: Efficiently moves water from one location to another.
Domestic Water Supply: Boosts water pressure for household use.

FOTING pump applications: garden watering, farm irrigation, and water transfer.

Image 7: A collage demonstrating the pump's versatility across various applications, including garden watering, farm irrigation, and general water transfer.

7. Vedligeholdelse

Regular maintenance ensures optimal performance and extends the pump's lifespan.

Regelmæssig inspektion: Periodically check all connections for leaks and ensure the pump is free from debris.
Rensning: Keep the pump exterior clean. Do not use harsh chemicals.
Vinterisering: In areas prone to freezing, drain the pump completely and store it in a warm, dry place to prevent damage from ice expansion.
Pressure Tank Maintenance: The pressure tank may require occasional air pressure adjustment. Consult a professional if you suspect issues with the tank's air charge.
Overophedningsbeskyttelse: The pump is equipped with overheat protection. If it shuts off unexpectedly, allow it to cool down before attempting to restart. Investigate the cause of overheating (e.g., dry running, blocked intake).

8. Fejlfinding

Se følgende tabel for almindelige problemer og deres mulige løsninger:

Problem	Mulig årsag	Løsning
Pumpen starter ikke	No power; tripped circuit breaker; faulty switch	Check power connection; reset breaker; inspect switch.
Pumpen kører, men der kommer ikke noget vand	Pump not primed; air leak in suction line; clogged intake; low water level in source	Prime the pump; check suction line for leaks; clear intake; ensure adequate water source.
Lavt vandtryk	Partially clogged lines; air in system; pressure tank air charge incorrect; worn impeller	Inspect and clear lines; bleed air from system; check pressure tank air charge; contact support for impeller inspection.
Pumpen tænder og slukker ofte	Small leak in system; pressure tank air charge too low; faulty pressure switch	Check for leaks in plumbing; adjust pressure tank air charge; inspect or replace pressure switch.
Pumpen larmer	Air in pump; cavitation; loose components; worn bearings	Prime pump thoroughly; ensure adequate water supply; tighten components; contact support for bearing issues.

9. Garantioplysninger

FOTING products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or contact FOTING customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.

10. Kundesupport

If you require technical assistance, have questions about your product, or need to report an issue, please contact FOTING customer service. Our team is available to provide professional technical support and ensure your water system remains stable.

Please visit the official FOTING website or refer to your product packaging for the most current contact information.