TOOLTOP ET2202 Bilbatteritester Brugermanual

1. Introduktion

This manual provides detailed instructions for the safe and effective operation of your TOOLTOP ET2202 Car Battery Tester. This device is designed to accurately test 12V and 24V lead-acid batteries, including standard flooded, AGM flat plate, AGM spiral, GEL, and EFB batteries. It measures battery voltage, internal resistance, and can perform starting and charging system tests, along with temperature measurement. Please read this manual thoroughly before use and retain it for future reference.

2. Sikkerhedsinstruktioner

• Always wear eye protection and protective clothing when working near batteries.
• Ensure the vehicle is in a well-ventilated area to prevent accumulation of explosive gases.
• Undlad at ryge eller tillade gnister eller flammer i nærheden af ​​batteriet.
• Undgå kontakt med batterisyre. Skyl straks med vand, og søg lægehjælp, hvis der opstår kontakt.
• Tilslut den røde clamp til den positive (+) terminal og den sorte clamp to the negative (-) terminal. Incorrect connection can damage the tester or battery.
• Brug ikke testeren, hvis den ser ud til at være beskadiget.
• Hold testeren væk fra børn.

3. Pakkens indhold

Bekræft, at alle nedenstående varer er til stede i din pakke:

• TOOLTOP ET2202 Car Battery Tester Unit
• Batteri Clamps (Rød for positiv, sort for negativ)
• USB kabel
• Temperatursensor
• Brugermanual
• Opbevaringspose

Figure 3.1: Contents of the TOOLTOP ET2202 package, including the tester, battery clamps, USB cable, temperature sensor, user manual, and storage pouch.

4. Produktet er slutview

The TOOLTOP ET2202 features a 3.2-inch color display and intuitive controls for easy operation. Below is a diagram highlighting the main components and their functions.

Figur 4.1: Forside view of the TOOLTOP ET2202 Battery Tester, showing the display, function buttons, and integrated battery clamps.

4.1. Enhedskomponenter

• 3.2-tommer farveskærm: Viser testresultater, batteritype, volumtage, charge status, and internal resistance.
• MODE knap: Navigates through different test modes (e.g., Battery Test, Cranking Test, Charging Test).
• Pileknapper: Used for selection and navigation within menus.
• Enter/Confirm Button: Bekræfter valg.
• Batteri Clamps: Red for positive (+), Black for negative (-). Connects to the vehicle battery.
• USB-port: For firmware updates or data transfer (if applicable).
• Temperaturfølerport: Connects the external temperature sensor.

5. Opsætning

1. Klargør batteriet: Sørg for, at batteripolerne er rene og fri for korrosion. Rengør dem om nødvendigt med en stålbørste.
2. Tilslut Clamps:
   • Tilslut rød positiv (+) clamp til den positive (+) pol på batteriet.
   • Tilslut sort negativ (-) clamp til den negative (-) pol på batteriet.

   Testeren tænder automatisk, når den er korrekt tilsluttet.

3. Tilslut temperatursensor (valgfrit): If temperature measurement is required, plug the temperature sensor into its designated port on the tester and attach the sensor tip to the battery surface.

Figure 5.1: Proper connection of the battery tester clamps til et bilbatteri.

6. Betjeningsvejledning

6.1. Hovedmenunavigation

Upon successful connection, the tester will display the main menu. Use the arrow buttons to navigate and the Enter button to select an option.

6.2. Batteritest

1. Fra hovedmenuen skal du vælge "Batteritest".
2. Select the battery type (e.g., STD, AGM, GEL, EFB).
3. Select the battery standard (e.g., CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB). Refer to your battery's label for the correct standard and rating.
4. Enter the rated CCA (Cold Cranking Amps) or other rating as indicated on the battery.
5. The tester will perform the test and display results including battery voltage, measured CCA, internal resistance, and battery health status (e.g., Good, Recharge, Replace).

6.3. Cranking Test (Starting System Test)

1. Fra hovedmenuen skal du vælge "Træktest".
2. Follow the on-screen prompts to start the vehicle engine.
3. The tester will monitor the starting voltage and display results, indicating the health of the starting system.

6.4. Charging Test (Alternator Test)

1. Fra hovedmenuen skal du vælge "Opladningstest".
2. Follow the on-screen prompts to rev the engine to a specified RPM (e.g., 2000-3000 RPM) for a few seconds.
3. The tester will analyze the alternator's output voltage og ripple voltage, providing a status on the charging system's performance.

6.5. Temperaturmåling

If the external temperature sensor is connected, the tester will display the battery's surface temperature during tests or as a separate reading, depending on the selected mode.

7. Vedligeholdelse

• Rensning: Tør testeren af ​​med en blød kludamp klæde. Brug ikke slibende rengøringsmidler eller opløsningsmidler.
• Opbevaring: Store the tester in its protective pouch in a dry, cool place away from direct sunlight and extreme temperatures.
• Kabelpleje: Inspicer batteriklemmenamps and cables regularly for any signs of damage. Replace if necessary.
• Firmwareopdateringer: Tjek producentens website periodically for available firmware updates to ensure optimal performance.

8. Fejlfinding

9. Specifikationer

• Model: ET2202
• Vise: 3.2 tommer farveskærm
• Anvendelse: 12V & 24V Lead-Acid Batteries (STD, AGM, GEL, EFB)
• Testområde: 100-2000 CCA
• Voltage Område: 8V-30V DC
• Driftstemperatur: -20°C til 50°C (-4°F til 122°F)
• Opbevaringstemperatur: -20°C til 70°C (-4°F til 158°F)
• Forbindelse: USB Port for data/updates
• Yderligere funktioner: Ekstern temperatursensorindgang

10. Garanti og support

For warranty information and technical support, please refer to the documentation included with your purchase or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.

Manufacturer: ETURBEV

For further assistance, please visit the official TOOLTOP webwebsted eller kontakt deres kundeservice.