PowMr 45A 100V MPPT solcelleladeregulator brugsanvisning

1. Introduktion

This manual provides essential information for the safe and efficient operation of your PowMr 45A 100V MPPT Solar Charge Controller. Please read it thoroughly before installation and use to ensure optimal performance and longevity of the device.

The PowMr 45A 100V MPPT Solar Charge Controller is designed to maximize power harvest from your solar panels and efficiently charge various battery types, including Sealed, LiFePO4, Gel, and Flooded batteries. It features an LCD display for parameter monitoring and adjustment, along with a USB port for convenience.

2. Sikkerhedsoplysninger

• Sørg for, at al ledningsføring udføres af kvalificeret personale.
• Always connect the battery to the controller first, then the solar panels. Disconnect in reverse order.
• Overskrid ikke den maksimale indgangsvolumentage of 100V from the solar panels.
• Install the controller in a well-ventilated area to prevent overheating.
• Avoid direct sunlight exposure to the controller.
• Use appropriate wire gauges for all connections to prevent overheating and ensure safety.

3. Produktet er slutview

The PowMr 45A 100V MPPT Solar Charge Controller features a robust design with an intuitive interface for easy monitoring and control.

3.1. Komponenter og grænseflade

• LCD-skærm: Shows real-time system data such as voltage, current, power, and battery status.
• Kontrolknapper: Used for navigating menus, adjusting parameters, and switching load output.
• Solar Input Terminals: Connect to solar panels (PV).
• Batteriterminaler: Connect to the battery bank.
• Indlæs udgangsterminaler: Connect to DC loads.
• Temperaturfølerport: For connecting the external temperature sensor (included).
• Kommunikationsport: For data monitoring and control via external devices (e.g., PC, mobile app).

4. Opsætning og installation

Follow these steps for proper installation of your MPPT solar charge controller:

1. Montering: Choose a suitable, well-ventilated location away from direct sunlight and moisture. Ensure adequate clearance around the unit for heat dissipation.
2. Forberedelse af ledningsføring: Loosen the screws on the controller's wiring ports counterclockwise to accommodate the cables. Ensure the cable trough is sufficiently open.
3. Batteriforbindelse: Connect the battery cables to the controller's battery terminals. Always connect the positive pole first, then the negative pole.
4. Solpaneltilslutning: Connect the solar panel cables to the controller's solar input terminals. Ensure correct polarity (positive to positive, negative to negative).
5. Belastningsforbindelse: Connect your DC loads to the controller's load output terminals.
6. Temperatursensor: Plug the temperature sensor into its dedicated port and attach the sensor to the battery to ensure accurate temperature compensation.
7. Sikre forbindelser: After all connections are made, tighten all terminal screws securely. Gently tug on the wires to ensure they are firmly seated.

5. Betjeningsvejledning

5.1. Skærmgrænseflade

The LCD display provides real-time information about your solar system. Short press the up/down scroll keys on the main interface to cycle through various parameter values. The system automatically switches parameter pages every 5 seconds if no button is pressed.

• Hovedgrænseflade: Shows solar panel input voltage, battery input voltage, and load output voltage.
• Cumulative Power Generation: Displays the total energy generated by the solar panels.
• Cumulative Discharge Capacity: Shows the total energy discharged to loads.
• Belastningsindikation: Indicates if a load is connected and active.

5.2. Parameterindstillinger

To enter the setting interface, press and hold the SET key on the main interface. In the setting interface, use the up/down page keys to select the desired battery type (e.g., Sealed, Gel, Flooded, Lithium, or custom). Short press the SET key to select input/output parameter values for adjustment. Use the up/down keys to modify the value, then press SET again to confirm and move to the next item.

The operating system automatically saves parameters and returns to the main interface after 10 seconds of inactivity. You can also press the ESC key to quickly save parameters and return to the main interface.

If system parameters are adjusted unreasonably, a fault indication will appear when returning to the main interface. To restore factory settings, press and hold both the SET and ESC keys simultaneously for 5 seconds on the main interface.

6. Vedligeholdelse

• Regularly inspect all wiring connections for tightness and corrosion.
• Keep the controller clean and free from dust and debris.
• Sørg for korrekt ventilation omkring enheden for at forhindre overophedning.
• Check the battery terminals for any signs of wear or damage.

7. Fejlfinding

• LCD Not Lighting Up: Tjek batterivolumentage and ensure all cables are correctly connected.
• Batteri Voltage Not Displayed: Verify battery connections and ensure the battery is not completely discharged.
• Solar LED Indicator Not Lit: Ensure solar panel cables are correctly connected and that there is sufficient sunlight.
• Fejlindikation: If a fault icon appears, refer to the manual for specific error codes and solutions. Incorrect parameter settings can trigger faults.

8. Specifikationer

9. Garanti og support

For warranty information, technical support, or service inquiries, please refer to the official PowMr webwebstedet eller kontakt deres kundeservice direkte. Gem din købskvittering som købsbevis i tilfælde af garantikrav.