SYNCO XTalk XPro2 2.4GHz Wireless Intercom Headset System

1. Introduktion

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your SYNCO XTalk XPro2 2.4GHz Wireless Intercom Headset System. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

Figure 1: SYNCO XTalk XPro2 Headset System and Accessories

2. Produktet er slutview

The SYNCO XTalk XPro2 is a full-duplex wireless intercom headset system designed for professional team communication. Key features include:

• Enhanced Signal Reception: External antennas provide a reliable 500m (1640ft) connection range.
• Avanceret støjreduktion: Features 2.0 AEC algorithm (150Hz to 7KHz) for clear voice recognition in noisy environments.
• Flexible Team Communication: Supports up to 13-unit connections with group expansion technology.
• Boost-tilstand: Enhances signal strength for stable communication through obstacles.
• Dominerende tilstand: One-button remote muting function for the Master headset.
• Lang batterilevetid: Over 24 hours of use with rechargeable and replaceable batteries.
• Realtidsovervågning: 3.5mm monitoring jack for simultaneous communication and device audio monitoring.

Figure 2: Enhanced Signal Reception

Figure 3: Advanced AEC Noise Reduction

3. Opsætning

3.1 Manuel parring

Follow these steps to manually pair your headsets:

1. Tænd for alle headset.
2. Set one headset as the Master and the others as Level 1.
3. Within 1 minute, long press all 'A' buttons. Release after the first beep. You will hear "Pairing Succeed".
4. Restart all headsets.

3.2 Using SYNCO EasyGo Software

For quick firmware upgrades, voice pack installations, and headset pairing, use the SYNCO EasyGo software. Refer to the user guide for software download and usage instructions from the SYNCO official site.

Figure 4: SYNCO EasyGo Software Interface

4. Betjeningsvejledning

4.1 Lydstyrkeindstillinger

Short press the volume '+' or '-' buttons on the headset to adjust the listening volume.

4.2 Slå lyden til/fra for mikrofon

To mute or unmute the microphone, rotate the boom arm up or down. Rotating it up mutes the microphone, and rotating it down unmutes it.

4.3 Støjreduktion

Short press button 'B' to toggle noise cancellation on or off. You will hear a beep to confirm the change.

4.4 Dominant Mode

Press and hold button 'B' to enter Dominant Mode. This mode allows the Master headset to mute all remote headsets instantly. Release the button to exit Dominant Mode.

4.5 Boost-tilstand

Long press the volume '-' button to hear a "beep", then release to switch between Mode 1, Mode 2, and Mode 3. Mode 2 is the default. Boost Mode enhances signal strength for stable communication, especially through obstacles.

4.6 Overvågning i realtid

Connect the headset to a device (e.g., camera, recorder) via the 3.5mm TRS port for real-time audio monitoring. This port is for monitoring only and does not output audio.

Figure 5: Real-Time Monitoring Setup

5. Indikatorer

The LED indicator on the microphone boom arm provides status information:

• Grønt lys konstant: Parring lykkes
• Green Light Flashing Slow: Ikke forbundet
• Green/Yellow Lights Alternating: Støjreduktion fra
• Red Light Flashing Slow: Lavt batteri
• Konstant rødt lys: Opladning

6. Vedligeholdelse

To ensure the longevity and optimal performance of your SYNCO XTalk XPro2 headset system, follow these maintenance guidelines:

• Rensning: Brug en blød, tør klud til at rengøre headsettet. Undgå at bruge skrappe kemikalier eller slibende materialer.
• Opbevaring: Opbevar headsettet et køligt, tørt sted væk fra direkte sollys og ekstreme temperaturer.
• Batteripleje: The system uses rechargeable and replaceable Lithium-Ion batteries. Ensure batteries are fully charged before extended use and stored properly if not used for long periods.
• Mikrofonbeskyttelse: Keep the microphone foam cover clean and replace if damaged to maintain audio quality.

Figure 6: 24-Hour Battery Life

7. Fejlfinding

If you encounter issues with your SYNCO XTalk XPro2 system, refer to the following common problems and solutions:

• No Audio/Intermittent Connection:
  • Ensure all headsets are powered on and fully charged.
  • Verify proper pairing between Master and Level 1 headsets (refer to Section 3.1).
  • Check the operating range; move closer to the Master headset.
  • Restart all headsets.
• Poor Audio Quality/Excessive Noise:
  • Ensure Noise Cancellation is activated (refer to Section 4.3).
  • Check microphone position and ensure it is not obstructed.
  • Verify that the microphone boom arm is fully down for unmuted operation.
• Headsettet oplader ikke:
  • Sørg for, at opladningskablet er korrekt tilsluttet til både headsettet og strømkilden.
  • Kontroller strømkilden for funktionalitet.
  • Verify the charging indicator (Red Light Steady) as per Section 5.

8. Specifikationer

9. Garanti og support

For warranty information, technical support, or service inquiries, please refer to the official SYNCO webwebstedet eller kontakt deres kundeservice direkte. Gem din købskvittering som købsbevis i tilfælde af garantikrav.