Pro-Ject Debut EVO 2 Audiophile Pladespiller Brugermanual

Indledning

This manual provides essential information for the setup, operation, maintenance, and troubleshooting of your Pro-Ject Debut EVO 2 Audiophile Turntable. Please read these instructions carefully before using the turntable to ensure proper function and longevity of the product.

Image: The Pro-Ject Debut EVO 2 turntable in High Gloss Red, featuring a clear dust cover, platter, and tonearm.

Sikkerhedsinstruktioner

• Always disconnect the turntable from the power supply before cleaning or maintenance.
• Rør ikke ved strømkablet med våde hænder.
• Avoid placing the turntable near water or excessive moisture.
• Ensure the turntable is placed on a stable, level surface to prevent vibrations and ensure proper operation.
• Hold emballagematerialer, især plastikposer, væk fra børn.

Hvad er der i æsken

Carefully unpack all items from the packaging. Please ensure all components listed below are present and undamaged.

• Pro-Ject Debut EVO 2 Pladespiller
• Transparent Dustcover
• Connection Cable (RCA)
• Strømadapter
• Justeringsvinkelmåler
• Single Adapter (for 45 RPM records with large center holes)
• Platter
• Kør bælte
• Modvægt
• Anti-skating vægt
• Pick it MM EVO Cartridge (pre-mounted)

Opsætning

1. Placering

Place the turntable on a firm, level surface, away from direct sunlight, heat sources, and excessive vibration. Ensure adequate ventilation around the unit.

2. Montering af tallerken og bælte

1. Place the main platter onto the sub-platter spindle.
2. Carefully loop the drive belt around the sub-platter and the motor pulley. Ensure the belt is not twisted.

Billede: En detaljeret view of the turntable's belt drive system, showing the belt wrapped around the sub-platter and motor pulley.

3. Tonearm Balance and Tracking Force

The Pick it MM EVO cartridge is pre-mounted. Follow these steps to set the tracking force:

1. Fjern stylus-beskytteren.
2. Place the counterweight onto the rear of the tonearm.
3. Adjust the counterweight until the tonearm floats freely and is perfectly balanced horizontally.
4. Rotate the tracking force dial (the numbered ring on the counterweight) to '0' without moving the counterweight itself.
5. Rotate the entire counterweight counter-clockwise until the desired tracking force is set. Refer to the cartridge specifications for the recommended tracking force (typically 1.8g for the Pick it MM EVO).

Image: A close-up of the carbon fiber tonearm, illustrating its construction and connection points.

4. Justering af anti-skating

The anti-skating mechanism counteracts the inward force on the tonearm. Attach the anti-skating weight's thread to the second groove of the anti-skating stub for the recommended tracking force.

Image: The anti-skating weight hanging from its thread, attached to the tonearm's anti-skating stub.

5. Forbindelse til en Amplivligere

Tilslut pladespillerens RCA-udgangskabler til 'Phono'-indgangen på din amplifier. Hvis din ampHvis højttaleren ikke har en dedikeret 'Phono'-indgang, skal du bruge en ekstern phono-forforstærker.amplivligere.

Image: The rear panel of the turntable, displaying the RCA output jacks for audio connection and the power input.

6. Montering af støvdæksel

Insert the hinges of the transparent dust cover into the designated slots at the rear of the turntable plinth.

Drift

1. Tænd/sluk

Connect the power adapter to the turntable and a wall outlet. The turntable is powered on by pressing the power button, usually located on the underside or side of the plinth.

2. Hastighedsvalg

The Debut EVO 2 features electronic speed selection. Use the speed selector switch (often a button on the plinth) to switch between 33 1/3 RPM and 45 RPM. For 78 RPM records, a special belt and stylus may be required (not included).

3. Afspilning af en plade

1. Læg en plade på fadet.
2. Vælg den korrekte afspilningshastighed.
3. Løft tonearmen ved hjælp af cue-håndtaget.
4. Placer tonearmen over den ønskede startrille på pladen.
5. Gently lower the tonearm using the cueing lever. The stylus will begin playing the record.

4. Stop af afspilning

At the end of a record, or when you wish to stop playback:

1. Løft tonearmen ved hjælp af cue-håndtaget.
2. Sæt tonearmen tilbage i dens hvileposition.
3. Sænk køhåndtaget.
4. Turn off the turntable if not playing another record.

Opretholdelse

1. Rensning

• Turntable Plinth and Dust Cover: Use a soft, lint-free cloth to wipe surfaces. For stubborn marks, a slightly damp en tør klud kan bruges. Undgå slibende rengøringsmidler.
• Fad: Clean the platter surface with a soft, dry cloth.

2. Pleje af pennen

• Regularly clean the stylus using a dedicated stylus cleaning brush, brushing gently from back to front.
• Undgå at berøre pennen med fingrene.
• Replace the stylus when signs of wear are apparent (e.g., distorted sound, increased surface noise). The Pick it MM EVO cartridge is designed for easy stylus replacement.

Billede: En detaljeret view of the Pick it MM EVO cartridge mounted on the tonearm, highlighting its design.

3. Udskiftning af bælte

The drive belt may stretch or degrade over time. If you notice inconsistent speed or reduced torque, the belt may need replacement. Contact Pro-Ject support or an authorized dealer for a replacement belt.

Fejlfinding

If you encounter issues with your turntable, consult the following table before contacting support.

Specifikationer

• Modelnavn: Debut EVO 2
• Mærke: Projekt
• Varemodelnummer: 9120129864930
• Produktdimensioner: 16.4 x 12.6 x 4.5 tommer (41.6 x 32 x 11.4 cm)
• Varens vægt: 13.2 pund (6 kilo)
• Materiale: Carbon Fiber (tonearm)
• Motortype: Bæltdrev
• Signalformat: Phono
• Inkluderede komponenter: Turntable, transparent dustcover, connection cable, power adapter, alignment protractor, single adapter
• Kompatible enheder: Amplifier, højttaler
• Fabrikant: Pro-Ject lydsystemer

Garanti

Pro-Ject Audio Systems offers a warranty for this product. Please refer to the warranty card included with your purchase or visit the official Pro-Ject webwebstedet for detaljerede garantivilkår og -betingelser. Gem din købsbevis til garantikrav.

Key Warranty Feature: 25-year spare parts availability guarantee, ensuring long-term support for your turntable.

Støtte

For further assistance, technical support, or spare parts, please contact your authorized Pro-Ject dealer or visit the official Pro-Ject Audio Systems webwebsted:

• Pro-Ject Store: Visit the Pro-Ject Store on Amazon
• Fabrikant: Pro-Ject lydsystemer