Indledning
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Total Automatic Self-priming Jet Pump, model TWP415006. Please read this manual thoroughly before operating the pump to ensure proper use and to prevent damage or injury.
Sikkerhedsinstruktioner
Overhold altid følgende sikkerhedsforanstaltninger for at mindske risikoen for brand, elektrisk stød eller personskade:
- Elektrisk sikkerhed: Sørg for, at strømforsyningen passer til pumpens volumentage (220-240V~50Hz). Always connect the pump to a properly grounded outlet. Do not operate the pump with a damaged cord or plug.
- Vandsikkerhed: Pump ikke brandfarlige eller ætsende væsker. Sørg for, at pumpen ikke er nedsænket i vand, medmindre den er specifikt designet til nedsænkbar brug. Beskyt pumpen mod frost.
- Installation: Install the pump in a dry, well-ventilated area, protected from direct sunlight and rain. Ensure stable mounting to prevent vibration.
- Opretholdelse: Disconnect power before performing any maintenance or repairs. Only qualified personnel should perform repairs.
- Børn og kæledyr: Hold børn og kæledyr væk fra pumpen under drift.
Produkt overview og komponenter
The Total Automatic Self-priming Jet Pump TWP415006 is designed for efficient water transfer. It includes a 24L cylindrical tank, pressure switch, pressure gauge, stainless steel hose, and brass 3-way connector.
Figur 1: Overview of the Total Automatic Self-priming Jet Pump TWP415006.
Figure 2: Key features of the pump, including 1500W power, 24L tank, and copper wire motor.
Inkluderede komponenter:
- 1 x Automatic Self-priming Jet Pump (1.5kW)
- 1 x 24L Cylindrical Tank
- 1 x trykkontakt
- 1 x Stainless Steel Hose
- 1 x trykmåler
- 1 x Brass 3-way Connector
Specifikationer
| Parameter | Værdi |
|---|---|
| Model | TWP415006 |
| Voltage | 220-240V~50Hz |
| Nominel effekt | 1500 W (2.0 HK) |
| Maks. Flyde | 100 l/min |
| Maks. Hoved | 60m |
| Maks. sugeevne | 9m |
| Rør diameter | 1 x 1 cm |
| Motortype | Kobbertrådsmotor |
| Impeller Materiale | Rustfrit stål |
| Pumpehus | Elektroforese |
| Skaft materiale | Stainless Steel Welding (304+45#) |
| Kabellængde | 0.3m |
| Varens vægt | 32 kilo |
| Pakkedimensioner | 62.7 x 57.3 x 36 cm |
Opsætning
1. Placering
- Choose a flat, stable, and dry location for the pump, protected from direct weather exposure.
- Sørg for tilstrækkelig ventilation omkring pumpen.
- Position the pump as close as possible to the water source to minimize suction lift.
2. Rørforbindelse
- Sugerør: Connect a rigid pipe of 1" diameter to the suction inlet. Ensure the suction pipe is airtight to prevent air leaks, which can affect priming and pump performance. Install a foot valve with a strainer at the end of the suction pipe in the water source to prevent debris from entering the pump and to maintain prime.
- Afgangsrør: Connect a 1" diameter pipe to the discharge outlet. The included stainless steel hose and brass 3-way connector should be used for the pressure tank and pressure gauge connection.
- Use thread sealant tape on all threaded connections to ensure a watertight seal.
3. Elektrisk tilslutning
- Ensure the power supply is 220-240V~50Hz.
- Connect the pump to a dedicated, properly grounded electrical outlet.
- Do not use extension cords unless absolutely necessary, and if so, ensure they are rated for outdoor use and the pump's power requirements.
4. Priming af pumpen
- Before first use, or if the pump has run dry, it must be primed.
- Locate the priming plug on the top of the pump casing.
- Fjern spædeproppen og fyld langsomt pumpen casinmed rent vand, indtil det løber over.
- Sæt spædeproppen sikkert på igen.
- Ensure the discharge valve is open before starting the pump.
Betjeningsvejledning
1. Start af pumpen
- Ensure the pump is properly primed (see Setup section).
- Bekræft, at alle forbindelser er sikre og lækagefri.
- Plug the pump into the grounded electrical outlet. The pump will start automatically when pressure drops below the set point of the pressure switch.
2. Overvågningsdrift
- Observe the pressure gauge to ensure the system is operating within expected pressure ranges.
- Lyt efter usædvanlige lyde eller vibrationer, som kan indikere et problem.
- Check for any leaks around connections.
3. Nedlukning
- To stop the pump, simply unplug it from the power source. The automatic pressure switch will also stop the pump when the desired pressure is reached.
- For extended periods of non-use, especially in freezing conditions, drain the pump and pipes completely to prevent damage.
Opretholdelse
1. Regelmæssig kontrol
- Periodically inspect the pump and all connections for signs of wear, damage, or leaks.
- Check the pressure tank's air charge annually. Refer to the tank's specific instructions for proper air pressure.
- Ensure the foot valve strainer is clear of debris.
2. Rensning
- Keep the pump exterior clean and free of dust and dirt to ensure proper cooling.
- Brug ikke hårde kemikalier eller slibende rengøringsmidler.
3. Vinterklargøring (til kolde klimaer)
- Hvis pumpen installeres i et område med frost, skal den tømmes helt for at forhindre skader fra isudvidelse.
- Disconnect power, open all drain plugs, and remove the priming plug to allow all water to escape.
- Store the pump in a warm, dry place if possible.
Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Pumpen starter ikke | No power; tripped circuit breaker; faulty motor. | Check power connection and circuit breaker. Consult a qualified electrician if motor is suspected faulty. |
| Pumpen kører, men der kommer ikke noget vand | Pump not primed; air leak in suction line; clogged foot valve/strainer; low water level in source. | Re-prime the pump. Check all suction connections for leaks. Clean foot valve strainer. Ensure adequate water in source. |
| Lavt tryk eller flow | Partial air leak; clogged impeller; worn components; incorrect pipe size. | Check suction line for small leaks. Inspect and clean impeller. Consult service for worn parts. Ensure correct pipe diameter. |
| Pumpen kører for ofte | Pressure tank air charge too low; leak in system; faulty pressure switch. | Check and adjust pressure tank air charge. Inspect entire system for leaks. Test or replace pressure switch. |
| Overdreven støj/vibration | Cavitation (air in pump); loose mounting; bearing wear. | Ensure pump is primed and no air leaks. Secure pump mounting. Consult service for bearing issues. |
Garanti og support
TOTAL products are manufactured to high-quality standards and are guaranteed against manufacturing defects. For warranty claims or technical support, please contact your local TOTAL authorized service center or the retailer from whom you purchased the product. Please retain your proof of purchase for warranty validation.
For yderligere hjælp kan du besøge TOTAL Butik på Amazon.
