Indledning
This manual provides detailed instructions for the safe and effective installation, operation, and maintenance of your SANUS Full Motion TV Mount. This mount is designed to securely hold flat-panel televisions ranging from 32 to 55 inches in size and weighing up to 55 pounds. Its full-motion capabilities allow for optimal viewfra forskellige positioner i et rum.

Image: The SANUS Full Motion TV Mount, showcasing its articulating arm and TV mounting plate. This mount is designed for single-stud installation and provides a wide range of motion for your television.
Sikkerhedsoplysninger
WARNING: Failure to read and follow all instructions, warnings, and cautions in this manual can result in personal injury, property damage, or voiding of your warranty.
- Ensure the mounting surface can support the combined weight of the mount and the television. This mount is designed for installation into a single wood stud. Do not install into drywall alone.
- Verify the TV's weight and VESA pattern are within the mount's specifications (32-55 inches, up to 55 lbs, VESA 75x75 to 400x400).
- Always use a qualified professional for installation if you are unsure about the structural integrity of your wall or the installation process.
- Do not overtighten screws. Overtightening can cause damage to the mount or your television.
- Hold alle små dele og emballagematerialer væk fra børn.
- Always use a stud finder to locate the center of the wood stud accurately.
- Two people are recommended for safe installation, especially when lifting the television.
Pakkens indhold
Before beginning installation, ensure all parts are present and undamaged. If any parts are missing or damaged, do not attempt to install. Contact Sanus customer support.
- Vægplademontering
- Tv-beslag (2)
- Assorted TV Mounting Hardware (screws, washers, spacers for various TV models)
- Wall Mounting Hardware (lag bolts, washers)
- Niveau
- Installationsskabelon
- Instruktionsmanual
Opsætning og installation
The SANUS Full Motion TV Mount is designed for easy DIY installation, typically taking 30 minutes or less. Follow these steps carefully.
Nødvendige værktøjer (ikke inkluderet)
- Stud Finder
- Bore
- Drill Bits (appropriate size for pilot holes)
- Topnøgle eller justerbar nøgle
- Phillips hovedskruetrækker
- Blyant
- Målebånd
Trin 1: Forbered væggen
- Using a stud finder, locate the center of a single wood stud at your desired TV height. Mark the center of the stud with a pencil.
- Hold the wall plate assembly against the wall, aligning the center hole with your stud mark. Use the integrated level to ensure it is perfectly horizontal. Mark the positions for the lag bolts.
- Drill pilot holes at the marked locations. Ensure the drill bit size matches the recommendations in the included installation guide to prevent splitting the stud or damaging the lag bolts.

Image: An installed SANUS TV mount on a wall, demonstrating its single-stud mounting capability. This design simplifies installation and is ideal for corner placements.
Trin 2: Monter vægpladen
- Align the wall plate with the pilot holes.
- Insert the lag bolts with washers through the wall plate and into the pilot holes.
- Using a socket wrench, tighten the lag bolts until the wall plate is securely fastened to the wall. Do not overtighten.
Step 3: Attach TV Brackets to Television
- Lay your television face down on a soft, clean surface to prevent scratches.
- Identify the correct size screws, washers, and spacers from the provided hardware kit that fit your TV's VESA mounting holes. Refer to your TV's manual for VESA pattern and screw length requirements.
- Attach the two TV brackets to the back of your television using the selected hardware. Ensure the brackets are centered and securely tightened.

Image: A diagram illustrating the compatibility of the full-motion wall mount with TVs ranging from 32 to 55 inches and supporting VESA patterns from 75x75 to 400x400 mm.
Step 4: Mount Television to Wall Plate
- With assistance, carefully lift the television and hook the TV brackets onto the wall plate assembly.
- Secure the TV to the mount using the locking mechanisms or screws as indicated in the detailed installation guide.
- Perform any post-installation leveling adjustments as needed. The mount allows for leveling adjustments even after the TV is hung.

Image: A close-up of a hand using a screwdriver to secure a component of the TV mount, emphasizing the easy 1-2-3 installation process that can be completed in approximately 15 minutes on a single stud.
For a visual guide, please refer to the official installation video (if available from the seller).
Video: An installation guide video would typically be embedded here, demonstrating the step-by-step process of mounting the TV. (Video not provided in input data)
Betjeningsvejledning
Your SANUS Full Motion TV Mount provides flexible viewvalgmuligheder:
- Udvidelse: Gently pull the TV away from the wall to extend it up to 19 inches. This allows for greater flexibility in viewing angles and access to the back of the TV. When not in use, push the TV back towards the wall for a low-profile finish, retracting to just 1.99 inches.
- Drejelig: The mount allows for up to 50 degrees of swivel to the left and right. Gently push the TV to the desired angle to optimize your viewing experience from any seat in the room.
- Vip: Adjust the TV's vertical angle by up to 15 degrees using the tool-free tilt mechanism. This feature is particularly useful for reducing glare from windows or lights, and for optimizing viewing when the TV is mounted above eye level, such as over a fireplace.
- Kabelstyring: Utilize the built-in cable management channels on the mount's arm to route and organize your TV cables for a clean and tidy appearance.

Billede: En side view of a TV mounted on the SANUS mount, illustrating its ability to extend up to 19 inches from the wall and retract to a slim 1.99 inches for a low-profile se.

Image: A TV mounted on the SANUS mount, demonstrating its 50-degree swivel capability to the left and right, allowing for versatile viewing vinkler.

Image: A TV mounted on the SANUS mount, showing a 15-degree downward tilt, highlighting the tool-free tilt feature designed to eliminate glare.

Image: A close-up of the SANUS mount's articulating arm with a cable routed through its integrated channels, demonstrating the built-in cable management feature for a clean setup.
Opretholdelse
To ensure the longevity and proper function of your SANUS TV mount, follow these simple maintenance guidelines:
- Rensning: Dust the mount regularly with a soft, dry cloth. For stubborn marks, a slightly damp en klud kan bruges, efterfulgt af øjeblikkelig tørring. Undgå slibende rengøringsmidler eller opløsningsmidler.
- Tjek forbindelser: Periodically (e.g., every 6-12 months), inspect all screws and bolts to ensure they remain securely tightened. Do not overtighten.
- Bevægelsestjek: Occasionally move the TV through its full range of motion (extension, swivel, tilt) to ensure smooth operation. If any stiffness is noted, ensure no cables are snagged.
Fejlfinding
If you encounter issues with your SANUS Full Motion TV Mount, refer to the following common problems and solutions:
| Problem | Mulig årsag | Løsning |
|---|---|---|
| TV'et er ikke i vater efter installation. | Initial leveling was off, or minor settling occurred. | Utilize the post-installation leveling adjustment feature. Refer to the detailed installation guide for specific instructions on how to adjust. |
| Vanskeligheder med at forlænge eller dreje tv'et. | Cables are snagged or mount joints are stiff. | Check that cables are properly routed through the cable management channels and are not obstructing movement. Ensure no objects are blocking the mount's path. |
| TV appears to sag or tilt unexpectedly. | Mounting screws are loose or TV weight exceeds capacity. | Immediately remove the TV from the mount. Re-check all wall and TV mounting screws for tightness. Verify your TV's weight is within the 55 lbs limit. If the issue persists, contact Sanus customer support. |
| Manglende hardware eller beskadigede dele. | Emballagefejl eller forsendelsesskade. | Do not proceed with installation. Contact Sanus customer support for replacement parts. |
Specifikationer
- Mærke: Sanus
- Model: Fuldt bevægeligt TV-beslag (ASIN: B0D5RLS8JP)
- Kompatible tv-størrelser: 32 til 55 tommer
- Maksimal vægtkapacitet: 55 pund
- Monteringstype: Wall Mount (Single Stud)
- Bevægelsestype: Artikulering (fuld bevægelse)
- Forlængelse fra væg: Op til 19 tommer
- Retracted Profile: 1.99 inches from wall
- Drejerækkevidde: Up to 50 degrees left and right
- Hældningsområde: Up to 15 degrees (tool-free)
- VESA-kompatibilitet: 75x75mm til 400x400mm
- Materiale: Metal
- Farve: Sort
- Varens vægt: Cirka 9.24 pund
- Pakkedimensioner: 20.04 x 11.85 x 2.56 tommer
- UPC: 793795537591
Garanti og support
SANUS stands behind the quality of its products. This TV mount comes with a 5 års garanti, der dækker defekter i materialer og udførelse ved normal brug.
For any questions, installation assistance, or troubleshooting, please contact Sanus customer service. Our U.S.-based experts are available 7 days a week to provide support.
Kontaktoplysninger:
- Refer to the official Sanus webhjemmeside for de seneste kontaktoplysninger.
- Online support resources and FAQs may also be available.





