1. Introduktion
This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your KATOOL KT-B750 Wheel Balancer. Please read this manual thoroughly before operating the machine to ensure proper usage and to prevent damage or injury. Keep this manual for future reference.
2. Sikkerhedsoplysninger
Always adhere to the following safety guidelines when operating the KATOOL KT-B750 Wheel Balancer:
- Ensure the machine is placed on a level, stable surface.
- Connect the machine to a properly grounded power outlet (110V).
- Brug passende personlige værnemidler (PPE), herunder sikkerhedsbriller og handsker.
- Hold hænder, hår og løstsiddende tøj væk fra bevægelige dele.
- Brug ikke maskinen, hvis nogen af delene er beskadigede eller mangler.
- Ensure the wheel guard is properly positioned before starting the balancing process.
- Kun uddannet personale bør betjene og vedligeholde dette udstyr.
- Afbryd strømmen, før du udfører vedligeholdelse eller justeringer.
3. Pakkens indhold
Ved udpakning skal du kontrollere, at alle komponenter er til stede:
- KATOOL KT-B750 Wheel Balancer Unit
- Hjulbeskyttelse
- Automatic Measurement Ruler
- Standard accessories for wheel mounting (e.g., cones, quick-release nut)
- Instruktionsmanual (dette dokument)
4. Opsætning
- Udpakning: Carefully remove the wheel balancer from its packaging. Inspect for any shipping damage.
- Placering: Position the machine on a firm, level concrete floor capable of supporting its weight and the weight of the wheels being balanced. Ensure adequate clearance around the machine for safe operation and maintenance.
- Forsamling:
- Attach the wheel guard to the designated mounting points. Ensure it can move freely and securely cover the wheel during operation.
- Connect the automatic measurement ruler if it is not pre-installed.
- Strømtilslutning: Connect the power cord to the machine and then to a dedicated 110V, grounded electrical outlet.
- Indledende kalibrering: Refer to the on-screen prompts or a dedicated section in the full manual for initial calibration procedures, which may include spindle calibration and weight tray calibration.
5. Betjeningsvejledning
Follow these steps for balancing a wheel:
- Monter hjulet: Securely mount the wheel onto the balancer's spindle using the appropriate cone and quick-release nut. Ensure the wheel is centered and tightened properly.
- Input Wheel Data:
- Use the automatic measurement ruler to measure the wheel's distance (A) and diameter (D). The machine will automatically input these values.
- Manually input the wheel's width (W) using the control panel.
- Select the desired balancing mode (e.g., static, dynamic, alloy wheel modes).
- Lower Wheel Guard: Close the wheel guard completely. The machine will not operate if the guard is open.
- Start Balancing Cycle: Press the START button on the control panel. The wheel will spin, and the machine will measure the imbalance.
- Læs resultater: Once the spin cycle completes, the display will show the required weight amounts and their precise locations for correction.
- Apply Weights: Open the wheel guard, apply the indicated balance weights to the inner and outer planes of the rim as shown on the display.
- Re-spin (Verification): Close the wheel guard and press START again to verify the balance. The display should show zero or minimal imbalance. Repeat the process if necessary until the wheel is balanced.
- Fjern hjul: Once balanced, open the wheel guard and carefully remove the wheel from the spindle.
6. Vedligeholdelse
Regular maintenance ensures the longevity and accuracy of your KATOOL KT-B750 Wheel Balancer:
- Rensning: Keep the machine clean, especially the spindle, control panel, and measurement ruler. Use a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Spindelsmøring: Periodically apply a light lubricant to the spindle threads to ensure smooth operation of the quick-release nut.
- Kalibreringstjek: Perform a calibration check regularly (e.g., monthly or after significant use) to maintain accuracy. Refer to the machine's specific calibration procedure.
- Kabelinspektion: Inspect all power cords and cables for signs of wear or damage. Replace damaged cables immediately.
- Hjulbeskyttelse: Ensure the wheel guard operates smoothly and securely. Clean any debris that might hinder its movement.
7. Fejlfinding
This section addresses common issues. For problems not listed, contact KATOOL customer support.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Maskinen tænder ikke. | Ingen strømforsyning; defekt strømledning; intern sikring sprunget. | Check power connection and outlet. Inspect power cord. Consult a qualified technician for fuse replacement. |
| Hjulet drejer ikke. | Wheel guard open; emergency stop engaged; motor issue. | Ensure wheel guard is closed. Check emergency stop button. Contact support if motor is unresponsive. |
| Inaccurate balancing results. | Improper wheel mounting; incorrect data input; machine out of calibration. | Re-mount wheel securely. Verify A, D, W values. Perform calibration procedure. |
| Automatic ruler not functioning. | Sensor obstruction; cable disconnection; ruler damage. | Clear any obstructions. Check cable connections. Contact support for repair. |
8. Specifikationer
- Model: KT-B750
- Mærke: KATOOL
- Strømforsyning: 110V
- Maximum Wheel Weight: 143 lbs (65 kg)
- Fælg diameter: 8" - 30"
- Fælgbredde: 1.5" - 20"
- Måling: Automatic measurement ruler for A and D values
- Dato først tilgængelig: 17. april 2024
9. Garanti og support
For warranty information and technical support, please contact KATOOL directly. Keep your purchase receipt as proof of purchase. Details regarding specific warranty periods and terms are typically provided at the point of sale or on the manufacturer's official webwebsted.
For assistance, please refer to the contact information provided by KATOOL or your authorized dealer.
