BluMill Self-Inflating Air Bed User Manual

Indledning

Thank you for choosing the BluMill Self-Inflating Air Bed. This manual provides essential information for the safe and efficient use of your new air bed. Please read these instructions carefully before setup and operation, and retain them for future reference.

Figur 1: The BluMill Self-Inflating Air Bed. This image shows the full view of the air bed, highlighting its grey flocked top surface and black PVC sides, with the integrated pump visible on one side.

Sikkerhedsoplysninger

• Elektrisk sikkerhed: The integrated pump operates on electricity. Do not immerse the pump or power cord in water. Ensure hands are dry when plugging or unplugging the unit.
• Overinflation: Do not over-inflate the air bed. Over-inflation can cause damage to the mattress and may lead to injury.
• Vægtgrænse: Overskrid ikke den maksimale vægtkapacitet på 100 kg (220 lbs).
• Skarpe genstande: Keep the air bed away from sharp objects, heat sources, and open flames to prevent punctures and damage.
• Børn og kæledyr: Do not allow children or pets to play unsupervised on or near the air bed.
• Temperatur: Avoid using the air bed in extreme temperatures, as this can affect the material's integrity.
• Kun husholdningsbrug: Dette produkt er beregnet til husholdningsbrug.

Pakkens indhold

Kontroller venligst pakkens indhold for at sikre, at alle varer er til stede:

• 1 x BluMill Self-Inflating Air Bed (Model 12079)
• 1 x Integrated Electric Pump (pre-installed)
• 1 x reparationssæt
• 1 x bæretaske

Opsætning og inflation

1. Pakker ud: Remove the air bed from its carry bag and unroll it on a clean, flat surface, free from sharp objects.
2. Find pumpen: Identify the integrated electric pump on the side of the air bed.
3. Tilslut: Connect the power cord of the integrated pump to a standard electrical outlet.
4. Pust op: Turn the rotary switch on the pump to the "INFLATE" position. The air bed will begin to inflate automatically.
5. Overvåg inflationen: The air bed will fully inflate in approximately 3 to 5 minutes. Monitor the firmness and turn the switch to "OFF" once the desired firmness is reached. Do not over-inflate.
6. Tag stikket ud: Disconnect the power cord from the electrical outlet and store it in the designated cable compartment on the pump.

Figur 2: Detail of the integrated electric pump. This image shows a close-up of the pump unit with a rotary switch for inflation and deflation, and the power cord compartment.

Figur 3: The BluMill Air Bed set up in a room, illustrating its use as a temporary sleeping solution. Icons below highlight key features: 1 Person Max 100kg, Built-in Pump, Optimal Support, and Inflates/Deflates in under 5 minutes.

Operating and Deflation

Justering af fasthed

The air bed's firmness can be adjusted during inflation. For a softer feel, stop inflation earlier. For a firmer feel, allow the pump to run longer, but always ensure not to over-inflate beyond the bed's capacity.

Deflation og opbevaring

1. Tilslut: Connect the power cord of the integrated pump to an electrical outlet.
2. Deflater: Turn the rotary switch on the pump to the "DEFLATE" position. The pump will begin to extract air from the mattress.
3. Fuldstændig deflation: Allow the pump to run until all air is removed and the mattress is flat. This typically takes 3 to 5 minutes.
4. Tag stikket ud: Disconnect the power cord and store it in its compartment.
5. Fold og gem: Carefully fold the deflated air bed and place it into the provided carry bag for compact storage.

Figur 4: The practical carry bag included with the BluMill Air Bed. This black fabric bag allows for easy and compact storage and transport of the deflated mattress.

Opretholdelse

Rensning

To clean the air bed, wipe the flocked surface and PVC sides with a damp cloth and mild soap. Do not use harsh chemicals or abrasive cleaners. Ensure the air bed is completely dry before storing.

Repairing Punctures

In case of a small puncture, use the included repair kit. Clean the area around the puncture, apply the patch according to the repair kit instructions, and allow sufficient time for it to cure before re-inflating the bed.

Fejlfinding

• Air Bed Not Inflating:
  • Sørg for, at netledningen er korrekt tilsluttet en fungerende stikkontakt.
  • Check that the rotary switch on the pump is set to the "INFLATE" position.
  • Verify there are no obstructions in the pump's air intake or output.
• Air Bed Not Holding Air / Losing Firmness:
  • Inspect the entire surface of the air bed for any punctures or leaks. Use soapy water to identify small leaks (bubbles will form).
  • Ensure the pump's rotary switch is fully in the "OFF" position after inflation to seal the air.
  • Check the valve cap (if applicable) for a secure seal.
  • Note that PVC material can stretch slightly during initial uses, which may give the impression of air loss. Re-inflate as needed.
• Pumpen virker ikke:
  • Tjek strømforsyningen.
  • Ensure the pump has not overheated. If it has, unplug it and allow it to cool for at least 20 minutes before attempting to use it again.

Specifikationer

Figur 5: Diagram illustrating the dimensions of the BluMill Air Bed. The image clearly shows the length (191cm), width (99cm), and height (36cm) of the mattress.

Garanti og support

For warranty information, please refer to the documentation provided with your purchase or contact BluMill customer support directly. Keep your proof of purchase for any warranty claims.

If you encounter any issues not covered in this manual or require further assistance, please contact BluMill customer service through their official webwebstedet eller forhandleren, hvor produktet blev købt.