1. Introduktion
This manual provides detailed instructions for the installation, operation, and maintenance of the LevelOne FCS-5202 Gemini 4 MP Fixed IP Camera. The FCS-5202 is an outdoor fixed camera designed for reliable and cost-effective IP surveillance networks. It is built to withstand various environmental conditions, including rain, extreme heat, snow, dust, and humidity. This camera delivers clear 4-megapixel resolution images and supports 802.3af Power over Ethernet (PoE) for combined power and data transmission over a single Cat.5 cable.
2. Produktet er slutview
2.1 Nøglefunktioner
- 4 Megapixel High-Definition Resolution for clear and sharp images.
- Supports H.264, H.265, and MJPEG video compression for efficient storage and streaming.
- Integrated 802.3af Power over Ethernet (PoE) for simplified installation with a single cable.
- IP67 Weather-Resistant Casing sikrer holdbarhed i udendørs miljøer.
- Advanced Motion Detection capabilities, including intrusion, camera tampering, and line crossing detection.
- Event notification support for immediate alerts.
2.2 Pakkens indhold
- LevelOne FCS-5202 IP Camera
- Installation Guide (refer to this manual)
- Monteringstilbehør
2.3 Kameradiagram
Figur 1: Forside og side view of the LevelOne FCS-5202 Gemini 4 MP Fixed IP Camera, showing the lens, IR LEDs, and mounting bracket.
3. Opsætning og installation
3.1 Sikkerhedsforanstaltninger
- Sørg for, at strømmen er afbrudt før installation eller vedligeholdelse.
- Install the camera in a location that provides optimal viewing and is protected from direct impact.
- Use appropriate tools and follow local electrical codes.
3.2 Fysisk installation
- Vælg et monteringssted: Select a suitable outdoor location, preferably under an overhang, that offers a clear field of view and is within reach of a network cable with PoE.
- Monter beslaget: Use the provided mounting accessories to securely attach the wall mount bracket to the chosen surface. Mark and drill pilot holes as necessary.
- Fastgør kameraet: Secure the camera to the mounting bracket. Adjust the camera's angle and orientation for the desired coverage.
3.3 Netværks- og strømtilslutning
- Tilslut Ethernet-kabel: Connect a Cat.5 or higher Ethernet cable from your PoE-enabled switch or PoE injector to the camera's Ethernet port. This single cable will provide both power and data.
- Tænd: Once the Ethernet cable is connected to a PoE source, the camera will power on automatically. Allow a few minutes for the camera to boot up.
3.4 Indledende konfiguration
- Opdag kameraet: Use the LevelOne IP Camera Finder tool (available on the LevelOne website) or a network scanner to locate the camera's IP address on your network.
- Adgang Web Interface: Åbn a web browser and enter the camera's IP address. You will be prompted to enter a username and password. Refer to the default credentials provided in the camera's packaging or on the manufacturer's webwebsted.
- Skift standardlegitimationsoplysninger: For security purposes, immediately change the default username and password to strong, unique credentials.
- Netværksindstillinger: Configure network settings such as static IP address (recommended for surveillance devices), subnet mask, gateway, and DNS servers as per your network requirements.
- Dato og tid: Set the correct date and time, preferably by synchronizing with an NTP server.
4. Betjeningsvejledning
4.1 Live View
Efter at have logget ind på kameraets web interface, navigate to the "Live View" section to see the real-time video feed from the camera. You can typically adjust stream quality and view options here.
4.2 Videooptagelse
- Kontinuerlig optagelse: Configure the camera to record video continuously to a Network Video Recorder (NVR) or network-attached storage (NAS).
- Hændelsesudløst optagelse: Set up recording to activate only when specific events occur, such as motion detection.
- Planlagt optagelse: Define specific time periods for recording.
4.3 Motion Detection and Event Management
- Konfigurer detektionszoner: In the camera's settings, define specific areas within the camera's view hvor bevægelsesdetektion skal være aktiv.
- Indstillinger for følsomhed: Adjust the sensitivity of motion detection to minimize false alarms.
- Begivenhedshandlinger: Specify actions to be taken when an event is detected, such as:
- Sending email notifications.
- Uploading recorded video clips to an FTP server.
- Triggering an alarm output (if available).
4.4 Fjernadgang
To access your camera remotely, you may need to configure port forwarding on your router or use a cloud-based service provided by LevelOne or a third-party NVR. Consult your router's manual or network administrator for port forwarding instructions.
5. Vedligeholdelse
5.1 Rengøring af kameraet
- Rengør regelmæssigt kameralinsen og huset med en blød klud.amp cloth to remove dust, dirt, and water spots.
- Do not use harsh chemicals or abrasive cleaners, as these can damage the lens or casing.
- Sørg for, at kameraet er slukket, inden rengøring.
5.2 firmwareopdateringer
Periodically check the LevelOne official website for firmware updates. Firmware updates can provide new features, improve performance, and enhance security. Follow the instructions provided with the firmware update package carefully.
6. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Kameraet tænder ikke. | No power from PoE switch/injector; faulty Ethernet cable. | Verify PoE source is active. Check Ethernet cable connection and integrity. Try a different PoE port or cable. |
| Cannot access camera via web browser. | Forkert IP-adresse; problem med netværksforbindelse; firewall blokerer adgang. | Confirm camera's IP address using discovery tool. Check network cable. Disable local firewall temporarily or add exception. Ensure camera and computer are on the same network segment. |
| Dårlig billedkvalitet. | Dirty lens; improper focus (if adjustable); low light conditions; network bandwidth issues. | Clean the lens. Check camera settings for resolution and quality. Ensure adequate lighting. Verify network bandwidth is sufficient for video streaming. |
| Bevægelsesdetektionen virker ikke, eller der er for mange falske alarmer. | Incorrect sensitivity settings; detection zones not configured properly; environmental factors (e.g., moving branches). | Adjust motion detection sensitivity. Refine detection zones to exclude irrelevant areas. Consider environmental factors. |
7. Specifikationer
| Feature | Detalje |
|---|---|
| Modelnummer | FCS-5202 |
| Opløsning | 4 megapixel |
| Videokomprimering | H.264, H.265, MJPEG |
| Forbindelse | Wired (802.3af Power over Ethernet - PoE) |
| Strømkilde | 802.3af PoE or 12V DC (Power adapter not included) |
| Strømforbrug | 5.76 watt |
| Materiale | Metal |
| Brugsmiljø | Udendørs |
| Vejrbestandighed | IP67-klassificeret |
| Dimensioner (L x B x H) | 6.05 x 15.4 x 7 cm (2.38 x 6.06 x 2.76 tommer) |
| Vægt | 640 gram (1.41 lbs) |
| Monteringstype | Vægmonteringsbeslag |
| Anbefalet brug | Motion detection, Outdoor surveillance |
8. Garanti og support
For warranty information, please refer to the documentation provided with your purchase or contact your reseller. LevelOne provides technical support for its products. For assistance, please visit the official LevelOne webwebsted eller kontakt deres kundeserviceafdeling.
Online ressourcer:
- LevelOne Official Webwebsted: www.level1.com
- Produktsupportside: Søg efter FCS-5202 on the LevelOne website for drivers, firmware, and FAQs.
