ProCom Heating ML250TPA-B 25,000 BTU Liquid Propane Ventless Infrared Plaque Heater Instruction Manual

1. Produktet er slutview

The ProCom Heating ML250TPA-B is a 25,000 BTU Liquid Propane Ventless Infrared Plaque Heater designed to provide efficient heating for indoor spaces up to 1150 sq. ft. This heater features a thermostat control for adjustable heat settings and can be used with included base feet for floor placement or mounted on a wall.

Billede 1.1: Forside view of the ProCom ML250TPA-B heater with base feet.

Nøglefunktioner:

• 25,000 BTU Output: Heats areas up to 1150 sq. ft.
• Ventilationsfrit design: No chimney or flue required.
• Infrared Plaque Heating: Provides radiant heat.
• Termostatstyring: High/Medium/Low settings for precise temperature management.
• Push Button Ignition: For easy startup.
• Oxygen Depletion Sensor (ODS): Slukker automatisk for varmeapparatet, hvis iltniveauet falder.
• Fleksibel installation: Includes base feet for floor standing and hardware for wall mounting.
• Ingen elektricitet kræves: Operates independently of electrical power, ideal for outages.

2. Sikkerhedsoplysninger

ADVARSEL: Forkert installation, justering, ændring, service eller vedligeholdelse kan forårsage skade på ejendom, personskade eller død. Læs installations-, betjenings- og vedligeholdelsesinstruktionerne grundigt, før du installerer eller servicerer dette udstyr.

• This is a ventless appliance. It uses air from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided.
• Always ensure proper ventilation when operating this heater. Consider using a carbon monoxide detector for added safety.
• Opbevar eller brug ikke benzin eller andre brændbare dampe og væsker i nærheden af ​​dette eller noget andet apparat.
• Hold området omkring varmeapparatet rent og fri for brandbare materialer, benzin og andre brandfarlige dampe og væsker.
• Never operate the heater in an area where it may be exposed to water.
• The Oxygen Depletion Sensor (ODS) is a safety feature that will shut off the heater if oxygen levels in the room become too low. Do not tampmed eller omgå denne sikkerhedsanordning.
• Ensure the heater is installed on a level, stable surface if using base feet, or securely mounted to a wall according to instructions.
• Keep children and pets away from the heater, especially during operation, as surfaces can become very hot.

3. Opsætning og installation

3.1 Udpakning og inspektion

Carefully remove the heater from its packaging. Inspect the unit for any shipping damage. If any damage is found, do not attempt to install or operate the heater. Contact your retailer or ProCom customer service immediately.

3.2 Valg af placering

Select a location that is clear of combustible materials. Ensure adequate clearance from walls and furniture as specified in the full manual. This heater is designed for indoor use only.

3.3 Assembly (Base Feet or Wall Mount)

The heater comes with both base feet for floor placement and hardware for wall mounting. Choose the installation method that best suits your needs.

Image 3.1: The heater package includes base feet and a wall bracket for flexible installation.

• For Floor Standing: Attach the provided base feet to the bottom of the heater using the supplied screws. Ensure the heater is stable and level.
• Til vægmontering: Use the included wall bracket and hardware to securely mount the heater to a suitable wall surface. Follow the detailed instructions in the complete manual for proper wall mounting to ensure stability and safety.

Billede 3.2: Eks.ample of the ProCom ML250TPA-B heater installed on a wall.

3.4 Propane Gas Connection

This heater operates on Liquid Propane (LP) gas. Connection to the LP supply must be performed by a qualified service person in accordance with local codes and ordinances. The heater does not require electricity for operation.

• A 3/8" Flare x 3/8" NPT Male brass 90-degree elbow and a 12 FT Propane Regulator Hose with a female flare nut end may be required for connecting to a 20 lb propane tank, especially if using the base feet to ensure proper clearance and prevent kinking of the hose.
• Ensure all connections are tight and leak-free. Perform a leak test with a soap solution before initial operation.

4. Betjeningsvejledning

4.1 Kontrolpanel overview

Image 4.1: The control panel features a Piezo Ignition button and a thermostat knob with variable heat settings.

The heater features a simple control panel with a Piezo Ignition button and a thermostat control knob. The thermostat knob allows you to select heat settings from "OFF PILOT" to various heat levels (e.g., 1-5 or High/Medium/Low).

4.2 Initial Startup Procedure

IMPORTANT: For the very first use, or after the heater has been disconnected from the propane supply for an extended period, the initial ignition may take longer than usual. This is normal as air needs to be purged from the gas lines.

1. Ensure the propane supply valve is fully open.
2. Turn the thermostat control knob to the "PILOT" position.
3. Press and hold the thermostat control knob down firmly.
4. While holding the knob down, repeatedly press the Piezo Ignition button until the pilot flame ignites. You may need to hold the knob down for several minutes (up to 10 minutes for the very first startup) to allow gas to reach the pilot.
5. Once the pilot flame is lit, continue to hold the thermostat control knob down for approximately 30-60 seconds to allow the thermocouple to heat up and hold the pilot flame.
6. Release the knob. If the pilot flame extinguishes, repeat steps 3-5.
7. Once the pilot flame is stable, turn the thermostat control knob to your desired heat setting (e.g., 3, 4, 5, or High/Medium/Low). The main burner will ignite.

NOTE: It is recommended to perform the first ignition outdoors or in a well-ventilated area, as a thin oil layer on internal components may burn off, causing a temporary odor or light smoke.

4.3 Justering af varmeafgivelse

Rotate the thermostat control knob to adjust the heat output. Higher numbers or "High" settings will provide more heat, while lower numbers or "Low" settings will reduce the heat output. The heater will cycle on and off to maintain the set temperature.

5. Vedligeholdelse

Regular maintenance ensures the safe and efficient operation of your ProCom heater. Always disconnect the heater from the propane supply and allow it to cool completely before performing any maintenance.

• Rensning: Keep the exterior of the heater clean. Use a soft, damp cloth to wipe down surfaces. Do not use abrasive cleaners or solvents. Ensure the air intake and exhaust vents are free from dust and debris.
• Inspektion af pilot- og brænder: Periodically inspect the pilot and main burner for any obstructions or unusual flame patterns. If the pilot flame appears weak or yellow, or if the main burner flames are not blue, contact a qualified service technician.
• Inspektion af gasledning: Regularly check the gas supply line and connections for any signs of wear, damage, or leaks.
• Opbevaring: If storing the heater for an extended period, disconnect it from the propane supply, clean it thoroughly, and store it in a dry, safe place.

6. Fejlfinding

Inden du kontakter kundeservice, vedrview følgende almindelige problemer og deres løsninger:

7. Specifikationer

8. Garanti og support

For warranty information, please refer to the documentation included with your product or visit the official ProCom website. It is important to retain your proof of purchase for any warranty claims.

Note on Warranty Claims: Some warranty processes may require specific documentation, such as a professional pressure reading of your propane system, to validate claims. Please review the warranty terms carefully.

For technical assistance, replacement parts, or further inquiries, please contact ProCom customer service through their official channels.