Emko ESM-1510-N Temperaturregulator Brugermanual

1. Introduktion

This manual provides essential information for the safe and efficient operation of your Emko ESM-1510-N Temperature Controller. Please read this manual thoroughly before installation, setup, or operation to ensure proper use and to prevent damage to the device or injury to personnel. Keep this manual for future reference.

2. Sikkerhedsoplysninger

Observe the following safety precautions to prevent electric shock, fire, or damage to the device:

• Installation and wiring must be performed by qualified personnel only.
• Sørg for, at strømforsyningen er afbrudt, før du udfører nogen form for ledningsføring eller vedligeholdelse.
• Kontroller, at forsyningen voltage matches the specifications of the controller.
• Do not expose the device to moisture, dust, or corrosive gases.
• Do not attempt to repair or modify the device. Refer all servicing to authorized personnel.
• Sørg for korrekt jording for at forhindre elektriske farer.

3. Produktet er slutview

The Emko ESM-1510-N is a 2-point temperature controller designed for precise temperature regulation in various industrial applications. It supports Pt1000 sensors and can measure temperatures from -50°C up to 400°C, featuring a 5A relay output for control. The front panel includes a digital display for current and set values, along with control buttons for parameter adjustment.

Figure 3.1: Front panel of the Emko ESM-1510-N Temperature Controller, showing the digital display, indicator LEDs (red for output, green for set value), and control buttons (up, down, set).

4. Installation

Follow these steps for proper installation of the temperature controller:

1. Montering: The ESM-1510-N is designed for panel mounting. Cut an opening of the specified dimensions (refer to the product datasheet for exact dimensions) in the control panel.
2. Secure the Controller: Insert the controller into the panel opening and secure it using the provided mounting clamps.
3. Miljøhensyn: Install the controller in an environment free from excessive vibration, high humidity, direct sunlight, and corrosive substances. Ensure adequate ventilation to prevent overheating.

5. Ledningsdiagram

Correct wiring is crucial for the safe and proper functioning of the controller. Refer to the detailed wiring diagram provided below. Ensure all connections are secure and comply with local electrical codes.

Figur 5.1: Eksample of a wiring diagram for the Emko ESM-1510-N. This diagram typically illustrates connections for power supply, Pt1000 sensor input, and relay output terminals. Always consult the diagram printed on the device or in the official datasheet for precise terminal assignments.

6. Setup and Parameter Configuration

The controller's parameters can be adjusted to suit specific application requirements. Follow these general steps to access and modify settings:

1. Tænd: Apply power to the controller. The display will show the current process value (PV).
2. Access Setpoint: Tryk på SÆT knap én gang til view the setpoint (SV). Use the UP og NED buttons to adjust the setpoint. Press SÆT again to confirm and return to PV display.
3. Access Parameter Menu: Tryk og hold på SÆT button for several seconds to enter the parameter menu. The display will show the first parameter code.
4. Navigationsparametre: Brug UP og NED buttons to scroll through parameter codes.
5. Modify Parameter Value: Trykke SÆT til view the value of the selected parameter. Use UP og NED for at ændre værdien. Trykke SÆT for at gemme den nye værdi.
6. Afslut menu: To exit the parameter menu, either scroll to the end of the menu or wait for a timeout, and the controller will automatically return to the normal operating display.

Fælles parametre:

7. Betjeningsvejledning

Once installed and configured, the ESM-1510-N operates automatically to maintain the set temperature. The display continuously shows the current process value (PV).

1. Overvågningstemperatur: The large red LED display shows the current temperature measured by the Pt1000 sensor.
2. Setpoint Indication: The green LED next to 'SV' illuminates when the setpoint is being displayed or adjusted.
3. Udgangsstatus: The red LED next to the relay symbol indicates the status of the relay output. It illuminates when the relay is active (e.g., heating element is on).
4. Temperaturkontrol: The controller will automatically activate or deactivate the relay output to maintain the temperature around the setpoint, based on the configured hysteresis or proportional band.

8. Vedligeholdelse

Regular maintenance ensures the longevity and accuracy of your temperature controller:

• Rensning: Rengør frontpanelet regelmæssigt med en blød, tør klud. Brug ikke slibende rengøringsmidler eller opløsningsmidler.
• Tilslutningskontrol: Kontrollér årligt alle elektriske forbindelser for tæthed og tegn på korrosion.
• Sensor inspektion: Check the Pt1000 sensor and its wiring for physical damage or degradation. Replace if necessary.
• Genkalibrering: If accuracy issues are suspected, consider recalibrating the sensor or the controller according to manufacturer guidelines or by a qualified technician.

9. Fejlfinding

Se tabellen nedenfor for almindelige problemer og deres mulige løsninger:

10. Specifikationer

11. Garanti og support

For warranty information, technical support, or service inquiries, please contact your authorized Emko distributor or the manufacturer directly. Keep your purchase receipt and product model number handy for faster assistance.