smartGyro Original Udskiftningsstøtteben Brugermanual

1. Produktet er slutview

This document provides essential information for the installation, usage, and maintenance of the smartGyro Original Replacement Kickstand, model PP27-086. This kickstand is specifically designed for smartGyro Speedway and Rockway electric scooters, ensuring perfect compatibility and optimal performance.

As an original smartGyro part, it is manufactured under strict quality controls to guarantee durability and reliability, preventing issues that may arise from using generic or low-quality components.

Figure 1: smartGyro Original Replacement Kickstand (Model PP27-086)

Figure 2: Original smartGyro Product Verification

2. Sikkerhedsoplysninger

Always prioritize safety when handling and installing replacement parts for your electric scooter. Failure to follow these guidelines may result in injury or damage to the product or scooter.

• Sluk: Ensure the electric scooter is completely powered off and disconnected from any power source before beginning installation.
• Stabil overflade: Perform installation on a stable, flat surface to prevent the scooter from tipping over.
• Korrekt værktøj: Use appropriate tools for installation. Refer to your scooter's main manual for specific tool requirements if necessary.
• Sikre fastgørelsesanordninger: Ensure all screws and fasteners are tightened securely after installation to prevent the kickstand from becoming loose during use.
• Børnesikkerhed: Keep the kickstand and any small parts out of reach of children.

3. Installation

This section outlines the general steps for installing the smartGyro replacement kickstand. Specific steps may vary slightly depending on your scooter model (Speedway or Rockway). It is recommended to consult your scooter's original manual for detailed instructions regarding kickstand removal and installation.

Tools Required (Commonly):

• Hex keys (Allen wrenches) of appropriate sizes
• Wrench (if applicable)

Installationstrin:

1. Forbered scooteren: Place your smartGyro Speedway or Rockway scooter on a stable surface, ensuring it cannot fall. It is advisable to have someone hold the scooter or prop it securely.
2. Locate Old Kickstand (if replacing): Identify the mounting point of the existing kickstand, typically located on the underside of the scooter deck near the rear wheel.
3. Remove Old Kickstand (if replacing): Using the appropriate tools, carefully loosen and remove the screws or bolts securing the old kickstand. Keep the fasteners for reuse if they are in good condition, or use new ones if provided with the replacement part.
4. Position New Kickstand: Align the smartGyro replacement kickstand with the mounting holes on your scooter. Ensure the kickstand is oriented correctly, allowing it to fold and unfold freely.
5. Secure the Kickstand: Insert the screws or bolts through the kickstand's mounting bracket and into the scooter's frame. Hand-tighten them initially.
6. Endelig stramning: Once all fasteners are in place, use your tools to securely tighten them. Do not overtighten, but ensure there is no wobble or looseness in the kickstand's attachment.
7. Test funktionalitet: After installation, gently test the kickstand by deploying and retracting it several times to ensure it operates smoothly and holds the scooter securely.

Figure 3: Kickstand installed on a smartGyro scooter

4. Brug

The smartGyro kickstand is designed for easy and reliable use to park your electric scooter safely.

• Deploying the Kickstand: To park your scooter, gently push the kickstand downwards with your foot until it clicks into its fully extended position. Ensure the scooter is stable before releasing det.
• Retracting the Kickstand: Before riding, use your foot to push the kickstand upwards and backwards until it is fully retracted and secured against the scooter's body. Ensure it is not dangling or interfering with the wheels.
• Parkeringsflade: Always park your scooter on a flat, stable surface. Avoid parking on inclines or uneven ground, as this may cause the scooter to tip over, potentially damaging the kickstand or the scooter itself.

5. Vedligeholdelse

Regular maintenance will extend the life of your smartGyro kickstand and ensure its proper function.

• Regelmæssig inspektion: Periodically check the kickstand for any signs of wear, damage, or bending. Inspect the mounting screws for tightness.
• Rensning: Clean the kickstand regularly with a damp klud til at fjerne snavs og snavs. Undgå at bruge skrappe kemikalier, der kan beskadige finishen.
• Smøring: If the kickstand's pivot point becomes stiff, apply a small amount of silicone-based lubricant to ensure smooth operation.
• Stram fastgørelsesanordninger: If you notice any looseness, gently tighten the mounting screws. Do not overtighten.

6. Fejlfinding

If you encounter issues with your smartGyro kickstand, refer to the following common problems and solutions:

7. Specifikationer

Figur 4: Produktemballage

8. Garanti og support

As an original smartGyro replacement part, this kickstand is manufactured to high standards. For specific warranty information regarding original smartGyro parts, please refer to the warranty policy provided with your original smartGyro scooter or visit the official smartGyro webwebsted.

For technical support or further assistance, please contact smartGyro customer service through their official channels. Ensure you have your product model number (PP27-086) and scooter model (Speedway or Rockway) available when seeking support.

You can find more information and contact details on the official smartGyro brand store: SMARTGYRO Amazon Store