1. Produktet er slutview
The LINGXIAO 48WUA1001C-II SPA Pump is a high-performance, two-speed motor designed for hot tubs and spas. It offers reliable operation and is engineered for compatibility with various OEM models, providing an efficient replacement solution.
1.1. Nøglefunktioner
- Modelkompatibilitet: Designed to be identical to original SPA factory pumps for perfect compatibility.
- Two-Speed Operation: Features a low speed (0.35HP, 3.8A) for continuous filtration and a high speed (1.5HP, 10.3A) for powerful jet action.
- Holdbar motor: Equipped with a pure copper winding motor, 80,000 capacitor charge-discharge cycle tested, and a thermal protector from Texas Instruments for long service life.
- Stille drift: Incorporates Anti-Creep Bearings for reduced noise during operation.
- Certificeringer: UL, CUL, ETL certified for safety and quality.
- Easy Plumbing: Connects to 2-inch plumbing and includes a free set of 2-inch unions for quick installation.
1.2. Produktkomponenter
The LINGXIAO SPA Pump consists of the main pump body, the motor housing, and connection unions. The pump is designed for easy integration into existing spa systems.
Figure 1: LINGXIAO 2 Speed Hot Tub SPA Pump (Model: 48WUA1001C-II) with included unions.
2. Opsætning og installation
2.1. Sikkerhedsforanstaltninger
- Always turn off the power to the hot tub at the circuit breaker before beginning any installation or maintenance.
- Ensure the hot tub is drained before disconnecting the old pump.
- Kontakt en kvalificeret elektriker, hvis du er usikker på den elektriske ledningsføring.
- Brug passende personlige værnemidler (PPE) under installationen.
2.2. Kontrol før installation
Before installing, verify that the new pump's specifications match your existing system. This model operates at 115V/60Hz. Confirm that your hot tub's plumbing and electrical connections are compatible.
2.3. Adjusting Discharge Location
The pump's discharge can be adjusted to one of three locations (12 o'clock, 3 o'clock, 9 o'clock) to fit your plumbing configuration. The factory default is 12 o'clock. To adjust, loosen the four indicated screws on the pump housing, rotate the wet end to the desired position, and then securely tighten the screws.
Figure 2: Adjusting the pump's discharge location.
Video 1: Visual guide on adjusting the pump's discharge location and general features.
2.4. VVS-tilslutning
Connect the pump to your hot tub's 2-inch plumbing using the provided unions. Ensure all connections are tight and leak-free. It is recommended to use plumbing sealant for a secure fit.
Figure 3: Plumbing connection with 2-inch unions.
2.5. Elektriske ledninger
This pump is a two-speed model designed for 115V/60Hz circuits. Proper wiring is critical for safe and correct operation. Refer to the diagram below and the instructional video for detailed wiring steps.
- Turn off power first.
- Ensure the corresponding voltage of the circuit (115V/60Hz).
- Tilslut Red wire (High speed) til terminal H.
- Tilslut White wire (Neutral wire) til terminal C.
- Tilslut Black wire (Low speed) til terminal L.
- Tilslut Green wire (Ground wire) til terminalen Jord.
Figure 4: 115V Two-Speed Wiring Diagram.
Video 2: Comprehensive guide on wiring the LINGXIAO 48WUA series SPA pump for two-speed operation.
3. Betjening
3.1. Indledende opstart
After successful installation and wiring, fill your hot tub with water. Ensure all valves are open and there are no airlocks in the system. Turn on the power to the hot tub. The pump should prime itself and begin circulating water.
3.2. Two-Speed Functionality
This pump offers two operational speeds:
- Lav hastighed: Ideal for continuous filtration and heating, drawing approximately 3.8 Amps and providing 0.35 HP.
- Høj hastighed: Provides maximum power for jets and hydrotherapy, drawing approximately 10.3 Amps and delivering 1.5 HP.
Switch between speeds using your hot tub's control panel.
3.3. Strømningshastighed
The pump is capable of delivering a maximum flow rate of 122 Gallons Per Minute (GPM) at high speed and a minimum flow rate of 53 GPM at low speed, ensuring efficient water circulation and powerful jet performance.
Figure 5: Pump Flow Rates.
4. Vedligeholdelse
4.1. Regelmæssig kontrol
- Periodically inspect the pump for any signs of leaks around the unions or pump seals.
- Listen for unusual noises during operation, which could indicate a bearing issue or debris in the wet end.
- Ensure the motor's cooling fan is free from obstructions to prevent overheating.
4.2. Rensning
Keep the exterior of the pump clean and free of dust and debris. Do not spray water directly onto the motor or electrical components.
4.3. Vinterklargøring
In climates where temperatures drop below freezing, it is essential to properly winterize your hot tub and pump to prevent freeze damage. This typically involves draining the pump and plumbing lines completely.
5. Fejlfinding
This section provides solutions to common issues you might encounter with your SPA pump.
5.1. Almindelige problemer
- Pumpen starter ikke:
- Kontroller, om afbryderen er udløst.
- Verify all electrical connections are secure and correctly wired (refer to Section 2.5).
- Ensure the hot tub's control panel is sending power to the pump.
- Low Pressure or No Water Flow:
- Check for airlocks in the plumbing system; try bleeding air from the pump or jets.
- Inspect the hot tub filter for clogs and clean or replace if necessary.
- Ensure all valves in the plumbing system are fully open.
- Check for debris or obstructions in the pump's wet end or impeller.
- Overdreven støj:
- A loud grinding or squealing noise may indicate worn bearings.
- Vibration can be caused by loose mounting bolts; ensure the pump is securely fastened.
- Air cavitation (sucking air) can cause noise; check water level and ensure no air leaks in the suction line.
5.2. Kontakt support
If you encounter issues that cannot be resolved using the troubleshooting steps above, please contact LINGXIAO PUMP Support through Amazon 'Ask a question'. Our technical support team is available to assist you within 24 hours.
6. Tekniske specifikationer
| Specifikation | Detalje |
|---|---|
| Mærke | LINGXIAO |
| Model | 48WUA1001C-II |
| Voltage | 115 volt (AC) |
| Power (High Speed) | 1.5 HK |
| Power (Low Speed) | 0.35 HK |
| Amperage (High Speed) | 10.3A |
| Amperage (Low Speed) | 3.8A |
| Maksimal flowhastighed | 122 gallon pr. Minut |
| Minimum flowhastighed | 53 gallon pr. Minut |
| Produktdimensioner | 8 cm L x 13 cm B x 8 cm H |
| Varens vægt | 26 pund |
| Materiale | Coiling iron |
| Fabrikant | LX |
7. Garanti og support
7.1. Garantioplysninger
The LINGXIAO 48WUA1001C-II SPA Pump comes with a 1-års garanti fra købsdatoen. Denne garanti dækker fabrikationsfejl og sikrer, at produktet opfylder de specificerede ydeevnestandarder under normal brug.
7.2. Kundesupport
For any questions, technical assistance, or warranty claims, please do not hesitate to contact LINGXIAO PUMP Support. You can reach us through the 'Ask a question' feature on Amazon. We are committed to providing prompt and helpful support within 24 hours to resolve any issues you may encounter.
