Brugsanvisning: Bagplade til Kryographics Next RTX 3080 Extended/RTX 3090 Extended, Passiv

1. Produktet er slutview

This document provides instructions for the installation, operation, and maintenance of the Aquacomputer Backplate for Kryographics Next RTX 3080 Extended / RTX 3090 Extended, Passive. This backplate is designed to enhance the passive cooling capabilities of your graphics card by providing additional surface area for heat dissipation from the rear of the PCB.

It is crucial to follow all instructions carefully to ensure proper installation and optimal performance of the backplate.

2. Pakkens indhold

Kontroller venligst, at alle komponenter er til stede, før installationen påbegyndes:

• 1x Aquacomputer Backplate for Kryographics Next RTX 3080 Extended / RTX 3090 Extended, Passive
• Mounting hardware (screws, washers, thermal pads - specific quantities may vary, refer to included diagram if available)

Note: The main product image shows the backplate itself. Please ensure all listed components are present.

3. Opsætning og installation

Before proceeding, ensure your computer is powered off and disconnected from the mains electricity. It is recommended to wear anti-static gloves to prevent damage to sensitive electronic components.

1. Prepare the Graphics Card: Carefully remove your graphics card from the computer. If a water block is already installed, ensure it is properly seated and secured.
2. Rene overflader: Gently clean the back of your graphics card's PCB and the contact surface of the backplate with isopropyl alcohol to remove any dust, oils, or residue. Allow to dry completely.
3. Påfør termiske puder: Apply the provided thermal pads to the designated areas on the backplate or the graphics card PCB, as indicated in the product's specific mounting diagram (if included). Ensure good contact and coverage over memory modules and VRMs on the back of the PCB.
4. Position the Backplate: Carefully align the backplate with the mounting holes on the rear of your graphics card.
5. Fastgør bagpladen: Using the provided screws and washers, gently secure the backplate to the graphics card. Tighten screws in a diagonal pattern to ensure even pressure. Do not overtighten, as this can damage the PCB.
6. Endelig kontrol: Visually inspect the installation to ensure the backplate is flush and securely attached without any gaps or misalignments.
7. Reinstall Graphics Card: Carefully reinstall your graphics card into your computer's PCIe slot and reconnect all necessary power cables.

Billede 1: Forside view of the Aquacomputer Backplate. This image displays the top surface of the backplate, featuring the 'RTX' cutout logo and various mounting holes for attachment to the graphics card.

Billede 2: Bagside view of the Aquacomputer Backplate. This image illustrates the underside of the backplate, highlighting the recessed areas designed for thermal pads to make contact with the graphics card's components, along with the corresponding screw holes.

4. Driftsmæssige overvejelser

As a passive cooling component, the backplate does not require active operation. Its effectiveness relies on proper installation and adequate airflow within your computer case. Ensure your system has good case ventilation to allow heat to dissipate efficiently from the backplate's surface.

5. Vedligeholdelse

Regular maintenance helps ensure optimal performance and longevity of your backplate:

• Fjernelse af støv: Periodically clean any dust accumulation from the surface of the backplate using compressed air or a soft, dry cloth. Ensure the computer is powered off before cleaning.
• Thermal Pad Inspection: If you notice a decrease in cooling performance, consider inspecting the thermal pads. Over time, thermal pads can degrade and may need replacement.
• Skruefasthed: Occasionally check the tightness of the mounting screws. Vibrations can sometimes cause screws to loosen slightly.

6. Fejlfinding

If you encounter issues after installing the backplate, consider the following:

• Poor Thermal Performance:
  • Verify that thermal pads are correctly placed and making good contact with both the PCB components and the backplate.
  • Ensure mounting screws are tightened evenly to apply consistent pressure.
  • Check for adequate airflow within your computer case.
• Backplate Not Fitting Correctly:
  • Double-check that the backplate model is compatible with your specific graphics card (Kryographics Next RTX 3080 Extended / RTX 3090 Extended).
  • Ensure no cables or other components are obstructing the backplate's seating.

7. Specifikationer

8. Garanti og support

Specific warranty details and direct support contact information are not provided within the available product data. For warranty claims or technical assistance, please refer to the official Aquacomputer website or contact your retailer of purchase. Keep your proof of purchase for any warranty-related inquiries.

9. Vigtige sikkerhedsoplysninger

• Always disconnect power from your computer before installing or performing maintenance on any internal components.
• Handle electronic components with care to avoid electrostatic discharge (ESD) damage. Use anti-static precautions.
• Do not overtighten screws, as this can damage the graphics card PCB.
• Opbevares utilgængeligt for børn.