ANYCUBIC Photon Mono X2 Resin 3D-printer brugermanual

1. Introduktion

This manual provides essential instructions for the safe and efficient operation of your ANYCUBIC Photon Mono X2 Resin 3D Printer. Please read this manual thoroughly before using the printer to ensure proper setup, usage, and maintenance. Retain this manual for future reference.

Image 1.1: The ANYCUBIC Photon Mono X2 Resin 3D Printer. This image displays the printer with its yellow UV-protective cover, the build platform, and a detailed miniature model printed with the device, highlighting its capability.

2. Sikkerhedsoplysninger

Always observe the following safety precautions when operating the ANYCUBIC Photon Mono X2:

• Brug beskyttelsesudstyr: Always wear gloves and safety glasses when handling resin to prevent skin and eye contact. Use a mask to avoid inhaling resin fumes.
• Ventilation: Operate the printer in a well-ventilated area to minimize exposure to resin odors and fumes.
• Harpikshåndtering: Store resin in a cool, dark place, away from direct sunlight and heat. Keep out of reach of children and pets. Do not ingest resin.
• Bortskaffelse: Dispose of uncured resin and contaminated materials according to local regulations. Cured resin can typically be disposed of as regular plastic waste.
• Elektrisk sikkerhed: Sørg for, at printeren er tilsluttet en jordet stikkontakt. Brug den ikke med våde hænder eller i damp forhold.
• UV lys: Avoid direct exposure to the printer's UV light source. The yellow cover provides UV protection during operation.
• Bevægelige dele: Hold hænder og løstsiddende tøj væk fra bevægelige dele under drift.

3. Pakkens indhold

Bekræft at alle komponenter er til stede i din pakke:

• ANYCUBIC Photon Mono X2 3D Printer
• Byg platform
• Harpiks Vat
• UV-Protective Cover
• Strømadapter og kabel
• USB-drev
• Tool Kit (Gloves, Mask, Scraper, Allen Wrenches, Funnel)
• Brugervejledning (dette dokument)

4. Produktet er slutview

The ANYCUBIC Photon Mono X2 is a high-precision resin 3D printer featuring a 9.1-inch 4K+ monochrome LCD screen. It utilizes an upgraded LighTurbo matrix light source for uniform UV exposure, resulting in detailed prints. The printer also includes dual linear guides for enhanced stability and a laser-engraved build plate for improved adhesion.

Nøglefunktioner:

• 9.1'' 4K+ Mono LCD Screen: Offers a resolution of 4096 x 2560 pixels, providing high detail with a single pixel size of 48µm.
• Upgraded LighTurbo Matrix Light Source: Projects UV light both parallel and perpendicular to the LCD screen for uniform exposure and improved print quality.
• Stable Printing Structure: Dual linear guides on the Z-axis reduce layer shifting, and a POM clearance nut with vibration absorption ensures accuracy and smooth model appearance.
• Lasergraveret byggeplade: Features a textured checkerboard pattern for significantly improved adhesion and print success rate, facilitating easier model removal.
• Anti-Scratch Film: Protects the LCD screen from resin leakage and potential damage.

Billede 4.1: Eks.ample of high-precision printing. This image highlights the detailed output achievable with the 4096 x 2560 pixel resolution of the Photon Mono X2's 4K+ mono screen.

Image 4.2: Uniform and efficient light source. This diagram illustrates the LighTurbo matrix light source projecting UV light evenly across the build area, crucial for consistent curing.

Image 4.3: Dual Linear Rail and POM Clearance Nut. This graphic demonstrates the Z-axis stability mechanism, featuring dual linear rails and a POM clearance nut designed to enhance precision and reduce layer lines.

Image 4.4: Laser Engraved Build Plate. This image shows the textured checkerboard pattern on the build plate, designed to improve print adhesion and facilitate easier removal of finished models.

5. Opsætning

5.1 Udpakning og placering

1. Tag forsigtigt printeren og alt tilbehør ud af emballagen.
2. Place the printer on a stable, level surface in a well-ventilated area, away from direct sunlight and heat sources.
3. Remove any protective films or packaging materials from the printer components.

5.2 Build Plate Leveling

Accurate leveling of the build plate is crucial for successful prints.

1. Ensure the resin vat is empty and clean.
2. Loosen the four screws on the build plate.
3. Place a leveling paper (or a standard A4 paper) on the LCD screen.
4. Lower the build plate until it firmly presses against the leveling paper.
5. Gently press down on the build plate to ensure it is flat against the screen, then tighten the four screws.
6. Raise the build plate slightly and remove the leveling paper.
7. Perform a Z-axis calibration if prompted by the printer's interface.

5.3 Installing the Resin Vat and Anti-Scratch Film

1. Carefully place the clean resin vat onto the printer's platform, ensuring it is securely seated.
2. If not pre-installed, apply the anti-scratch film to the LCD screen according to the instructions provided with the film. This protects the screen from resin spills.

Image 5.1: Anti-Scratch Film Installation. This image illustrates the process of applying the protective film over the LCD screen, which safeguards against resin damage.

6. Betjeningsvejledning

6.1 Preparing Your 3D Model (Slicing)

The Photon Mono X2 is compatible with various slicing software, including Anycubic Photon Workshop, CHITUBOX, and Lychee. Ensure you use the correct printer profile for the Photon Mono X2.

1. Import your 3D model (e.g., .STL, .OBJ) into your chosen slicing software.
2. Orient and position the model on the virtual build plate.
3. Add supports as necessary to prevent print failures.
4. Set print parameters (layer height, exposure time, bottom layer count, etc.) according to your resin type and desired print quality. Refer to your resin manufacturer's recommendations.
5. Slice the model and save the output file (typically .pmx2 format) to a USB drive.

Image 6.1: Slicer Software Compatibility. This image displays a computer screen running 3D slicing software, indicating compatibility with popular programs like Photon Workshop, CHITUBOX, and Lychee for preparing models.

6.2 Start af en udskrivning

1. Ensure the build plate is clean and securely attached.
2. Pour resin into the resin vat, ensuring it does not exceed the maximum fill line.
3. Insert the USB drive containing your sliced file into the printer's USB port.
4. Place the UV-protective cover over the printer.
5. On the printer's touchscreen, navigate to the "Print" menu, select your file, and confirm to start printing.
6. Monitor the initial layers to ensure proper adhesion to the build plate.

6.3 Post-Processing

1. Once printing is complete, carefully remove the build plate from the printer.
2. Using the provided scraper, carefully detach the printed model from the build plate.
3. Wash the model in isopropyl alcohol (IPA) or a suitable resin cleaner to remove uncured resin.
4. Cure the model under UV light (e.g., in a curing station or direct sunlight) until fully hardened.
5. Remove supports and perform any necessary finishing work.

7. Vedligeholdelse

7.1 Cleaning the Resin Vat

• After each print, filter any remaining resin back into its bottle using a mesh filter.
• Clean the resin vat with IPA and a soft cloth. Avoid using sharp objects that could damage the FEP film.
• Inspect the FEP film for damage or cloudiness. Replace if necessary.

7.2 Rengøring af byggepladen

• Clean the build plate with IPA after each print to remove any resin residue.
• Ensure the build plate is completely dry before starting a new print.

7.3 LCD Screen Care

• Regularly inspect the LCD screen for resin spills or damage.
• If resin spills onto the screen, clean it immediately with IPA and a soft, lint-free cloth. Do not use abrasive materials.
• Ensure the anti-scratch film is in good condition. Replace it if it becomes damaged.

8. Fejlfinding

9. Specifikationer

10. Garanti og support

ANYCUBIC provides a standard warranty for its products. For specific warranty terms, duration, and conditions applicable to your region, please refer to the official ANYCUBIC webwebstedet eller garantikortet, der følger med dit produkt.

For technical support, troubleshooting assistance, or spare parts, please contact ANYCUBIC customer service through their official website or the contact information provided in your product documentation. When contacting support, please have your model number (Photon Mono X2) and purchase details ready.

Officiel Webwebsted: www.anycubic.com