1. Introduktion
This manual provides instructions for the proper installation and use of the Morris Products 15067 90 Degree Flex Duplex Box Connector. This connector is designed for connecting two pieces of flexible metallic conduit (FMC), AC, MC, or NM sheathed cable to a steel box or other metal enclosure using a single knockout opening.
Image: Two Morris Products 15067 90 Degree Flex Duplex Box Connectors. These zinc die-cast connectors feature a 90-degree bend, designed for connecting two pieces of flexible metallic conduit or various types of sheathed cables to an electrical box.
2. Hvad er der i æsken
The Morris Products 15067 package typically includes:
- Two (2) 3/8" Duplex 90 Degree Connectors (Model 15067)
3. Specifikationer
| Feature | Detalje |
|---|---|
| Modelnummer | 15067 |
| Connector Type | 90 Degree Flex Duplex Box Connector |
| Materiale | Støbt zink |
| Handelsstørrelse | 3/8" FMC (fits 1/2" knockout) |
| Screw Design | 2 Screw design, Combo Head Screws |
| Anvendelige kabler | Flexible Metallic Conduit, AC, MC, NM sheathed cable |
| NM Cable Compatibility | 14/2 Thru 12/3 NM |
| AC Cable Compatibility | 14/2 Thru 10/4 AC |
| MC Cable Compatibility | 14/2 Thru 10/3 MC |
| Certificeringer | cULus Listed |
| Produktdimensioner | 4 x 6 x 12 tommer |
| Vægt | 0.32 ounce |
4. Installationsvejledning
The Morris Products 15067 connector is designed for use in dry locations to connect two pieces of flexible metallic conduit or various types of sheathed cables to a steel outlet box or other metal enclosure.
Nødvendige værktøjer (ikke inkluderet):
- Screwdriver (compatible with combo head screws)
- Wire strippers/cutters (as needed for cable preparation)
- Pliers or wrench (for tightening locknut, if applicable)
Installationstrin:
- Forbered kabinettet: Ensure the steel box or metal enclosure has a 1/2" knockout opening available for the connector. Remove the knockout if not already done.
- Prepare the Cables: For each of the two cables (Flexible Metallic Conduit, AC, MC, or NM sheathed cable) to be connected, prepare the ends according to standard electrical practices, ensuring proper length and removal of outer sheathing as required for connection.
- Insert Cables into Connector: Loosen the two combo head screws on the connector. Insert one prepared cable end into each of the two openings of the 90-degree duplex connector. Ensure the cables are fully seated within the connector's clamps.
- Sikre kabler: Tighten the two combo head screws firmly to secure both cables within the connector. Do not overtighten, but ensure a secure grip to prevent cable pull-out.
- Attach Connector to Enclosure: Insert the threaded end of the connector through the 1/2" knockout opening in the steel box or metal enclosure.
- Sikker forbindelse: Thread the locknut (if supplied separately or integrated) onto the threaded end of the connector from inside the enclosure and tighten it securely to fasten the connector to the box.
- Endelig kontrol: Verify that both cables are securely held by the connector and that the connector is firmly attached to the enclosure. Ensure all connections comply with local electrical codes.
5. Betjeningsvejledning
The Morris Products 15067 connector is a passive component designed to facilitate secure electrical connections. Once properly installed as per the installation instructions, it operates by maintaining the physical and electrical integrity of the cable connections to the enclosure. No ongoing operational steps are required beyond initial installation.
Vigtig: Ensure all electrical work is performed by qualified personnel and adheres to all applicable national and local electrical codes.
6. Vedligeholdelse
The Morris Products 15067 90 Degree Flex Duplex Box Connector is a low-maintenance component. Once installed correctly, it typically requires no routine maintenance.
Periodiske kontroller:
- Visuel inspektion: Periodically inspect the connector and surrounding cables for any signs of physical damage, corrosion, or loosening.
- Tæthed: If accessible and safe to do so (with power disconnected), occasionally check the tightness of the screws securing the cables and the locknut securing the connector to the box. Retighten if necessary.
Note: Always disconnect power before performing any inspection or maintenance on electrical components.
7. Fejlfinding
Most issues related to the Morris Products 15067 connector stem from improper installation. Review the installation steps carefully if you encounter problems.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Cables are loose in the connector. | Screws not tightened sufficiently. | Ensure power is off. Retighten the two combo head screws on the connector firmly. |
| Connector is loose on the enclosure. | Locknut not tightened properly. | Ensure power is off. Tighten the locknut on the threaded end of the connector from inside the enclosure. |
| Cannot insert cable into connector. | Screws not loosened enough; incorrect cable type/size. | Ensure screws are fully loosened. Verify cable type and size are compatible with the connector's specifications (e.g., 14/2 Thru 12/3 NM, 14/2 Thru 10/4 AC, 14/2 Thru 10/3 MC). |
| Connector does not fit knockout. | Incorrect knockout size. | This 3/8" FMC connector is designed to fit a 1/2" knockout. Ensure the knockout size is correct. |
If issues persist or you are unsure about any electrical work, consult a qualified electrician.
8. Garanti og support
For warranty information and technical support regarding Morris Products, please refer to the official Morris Products webwebstedet eller kontakt deres kundeservice direkte. Gem din købskvittering til garantikrav.
Kontaktoplysninger for Morris Products:
- Webwebsted: www.morrisproducts.com (Bemærk: Dette er en pladsholder URL, please verify the actual manufacturer's webwebsted for support.)
- Kundeservice: Der henvises til webwebsted for kontaktnumre eller e-mailsupport.
