1. Introduktion
This manual provides detailed instructions for the installation, operation, and maintenance of your EDGE Xtreme Series EDX1800.2FD-E0 2-Channel AmpLæs venligst denne manual grundigt, inden du forsøger at installere eller betjene den, for at sikre korrekt brug og for at forhindre skader på enheden eller dit køretøjs lydsystem. Gem denne manual til senere brug.
Figur 1.1: Overview of the EDGE Xtreme Series EDX1800.2FD-E0 2-Channel Amplifer. Dette billede viser toppen og siden view af amplifier, highlighting its robust heatsink design and compact form factor.
2. Sikkerhedsoplysninger
Vigtige sikkerhedsforanstaltninger:
- Frakobl altid bilens negative batteripol, inden du påbegynder elektrisk arbejde.
- Sørg for, at alle ledninger er korrekt ført og fastgjort for at forhindre skader fra skarpe kanter eller bevægelige dele.
- Brug strøm- og jordledninger med passende diameter som angivet i installationsafsnittet.
- Install an inline fuse on the main power cable, close to the battery, to protect against short circuits.
- Undgå at montere ampopbevar apparatet på steder, der er udsat for direkte sollys, overdreven varme, fugt eller støv.
- Betjen ikke amplifier if it is damaged or malfunctioning. Refer to the troubleshooting section or contact support.
3. Pakkens indhold
Bekræft at alle varer er til stede i pakken:
- EDGE Xtreme-serien EDX1800.2FD-E0 2-kanals Amplivligere
- Fjernbetjening til bas
- Monteringsudstyr (skruer, skiver)
- Brugervejledning (dette dokument)
4. Produktet er slutview og funktioner
The EDGE Xtreme Series EDX1800.2FD-E0 is a high-performance 2-channel amplifier designed for car audio applications. It utilizes a full bridge Class D topology, allowing for high power output in a compact form factor. The custom-designed heatsink ensures efficient heat dissipation for reliable operation.
Nøglefunktioner:
- 2-kanals strøm Amplivligere: Capable of driving two speakers or one speaker in bridged mode.
- Maksimal effekt: 7200 watt.
- Klasse D topologi: Ultra-efficient design for high power and reduced heat generation.
- Full Bridge Power Delivery: An efficient method for converting DC power to AC output.
- Integrated Active Crossovers: High-Pass Filter (HPF) and Low-Pass Filter (LPF) for precise sound tuning.
- Bass Boost Circuit: Adjustable bass enhancement for low-frequency output.
- Brugerdefineret køleplade: Engineered for optimal thermal management.
Figur 4.1: EDGE Xtreme Series Power Amplifiers. This image illustrates the design aesthetic shared across the Xtreme Series, emphasizing the compact and powerful nature of these amplivførere.
5. Opsætning og installation
Korrekt installation er afgørende for optimal ydeevne og sikkerhed. Hvis du er usikker på nogen del af installationsprocessen, bør du kontakte en professionel installatør af bilstereo.
5.1 Montering af Amplivligere
- Vælg et monteringssted, der er tørt, godt ventileret og beskyttet mod direkte sollys eller overdreven varme.
- Ensure there is sufficient airflow around the amplifier's heatsink for proper cooling.
- Brug det medfølgende monteringsudstyr til at fastgøre det sikkert amplifier to a solid surface in the vehicle.
5.2 Ledningsforbindelser
Refer to the diagrams below for proper wiring. All connections must be secure and free from corrosion.
Figur 5.1: Power Input Terminals. This image shows the power input side of the amplifier, detailing the +12V, REM (Remote), and GND (Ground) terminals.
- Strøm (+12V): Connect a heavy-gauge power cable (e.g., 4 AWG or larger, depending on total system power) from the vehicle's positive battery terminal to the ampsikringsholderen på +12V-terminalen. Installer en indbygget sikringsholder inden for 45 cm fra batteriet.
- Jord (GND): Tilslut et kraftigt jordkabel af samme størrelse som strømkablet fra amplifier's GND terminal to a clean, unpainted metal surface on the vehicle chassis. Ensure a good electrical connection.
- Fjernbetjening (REM): Tilslut en fjernbetjeningsledning (typisk 18 AWG) fra din hovedenheds fjernbetjeningsudgang til ampforsyningens REM-terminal. Denne ledning tænder amptænd og sluk for støjrelæet med din hovedenhed.
Figur 5.2: Control Panel and Speaker Outputs. This image displays the amplifier's control panel, including RCA low-level inputs, crossover adjustments (HPF, LPF), gain boost, and speaker output terminals.
- Lav indgang (RCA): Tilslut RCA-kabler fra din hovedenheds for-amp udgange til amplifier's LOW INPUT terminals (Left and Right).
- Højttalerudgange: Tilslut dine højttalere til amplifier's speaker output terminals. Ensure correct polarity (+ to + and - to -). For bridged operation, refer to the markings on the amplifier and connect to the designated terminals.
6. Betjeningsvejledning
Når amplifier is correctly installed and wired, you can proceed with initial setup and adjustments.
6.1 Indledende opstart
- After all connections are made, reconnect the vehicle's battery negative terminal.
- Tænd din hovedenhed. amplifier's power indicator (PWR) should illuminate. If not, refer to the troubleshooting section.
- Start with all gain controls at their minimum setting.
6.2 Justering af betjeningselementer
- Gevinst: Play a familiar piece of music. Slowly increase the GAIN control until you hear distortion, then back it off slightly. This sets the ampjusterers indgangsfølsomhed, så den passer til din hovedenheds udgang.
- Højpasfilter (HPF): If driving full-range speakers, adjust the HPF to cut off low frequencies that the speakers cannot reproduce effectively. This protects smaller speakers and improves clarity.
- Lavpasfilter (LPF): If driving subwoofers, adjust the LPF to allow only low frequencies to pass through. This ensures the subwoofer plays only bass notes.
- Bass Boost: Use the BASS BOOST control to enhance low frequencies. Use sparingly to avoid distortion and potential speaker damage.
- Fjernbetjening til bas: The included remote bass control unit allows for convenient adjustment of bass levels from the driver's seat.
6.3 Bridged Operation
The EDX1800.2FD-E0 can be bridged to provide higher power output to a single speaker, typically a subwoofer. Refer to the speaker output terminals on the amplifier for specific bridged wiring instructions. Ensure the speaker's impedance is compatible with bridged operation (typically 4 ohms minimum).
7. Vedligeholdelse
The EDGE EDX1800.2FD-E0 ampLifier kræver minimal vedligeholdelse for at sikre langsigtet ydeevne.
- Rensning: Tør regelmæssigt af ampRengør ydersiden af apparatet med en blød, tør klud. Brug ikke skrappe kemikalier eller slibende rengøringsmidler.
- Inspektion: Regularly check all wiring connections for tightness and signs of corrosion. Ensure the mounting is secure.
- Ventilation: Sørg for, at amplifier's heatsink fins are free from obstructions (e.g., dust, debris) to maintain proper cooling.
8. Fejlfinding
Hvis du oplever problemer med din ampLifier, se følgende tabel, før du kontakter support.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Ingen strøm (PWR-LED slukket) | Sprunget sikring, løs strøm-/jord-/fjernbetjeningsledning, defekt ledningsføring. | Check inline fuse, verify all power, ground, and remote connections. Test voltage at +12V and REM terminals. |
| Ingen lydudgang | RCA cables disconnected, speaker wires disconnected/shorted, gain too low, head unit not sending signal. | Check RCA and speaker connections. Increase gain. Verify head unit output. |
| Forvrænget lyd | Gain set too high, speaker impedance mismatch, faulty speaker, poor ground connection. | Reduce gain. Check speaker impedance. Inspect speaker for damage. Verify ground connection. |
| AmpOverophedning af væske | Utilstrækkelig ventilation, for lav impedans, langvarig høj effekt. | Ensure proper airflow around heatsink. Check speaker impedance. Reduce volume or gain. |
9. Specifikationer
The following are the technical specifications for the EDGE Xtreme Series EDX1800.2FD-E0 amplivligere:
- Modelnummer: EDX1800.2FD-E0
- Mærke: KANT
- Antal kanaler: 2
- Maksimal effekt: 7200 W
- Topologi: Class D, Full Bridge
- Voltage: 230 volt (drift)
- Minimumsforsyning Voltage: 24 volt
- Monteringstype: Overflademontering
- Dimensioner (L x B x H): 39.4 x 27 x 10 cm (15.5 x 10.6 x 3.9 tommer)
- Vægt: 3.2 kg (7.05 pund)
- Integrerede funktioner: Active Crossovers (HPF/LPF), Bass Boost Circuit
10. Garanti og support
10.1 Garantioplysninger
EDGE products are designed and manufactured to the highest standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official EDGE webwebsted. Gem din købsbevis til garantikrav.
10.2 Kundesupport
If you require further assistance or have questions not covered in this manual, please contact EDGE customer support through their official website or the retailer where the product was purchased. Provide your model number (EDX1800.2FD-E0) and a detailed description of your issue for efficient support.
