1. Introduktion
This manual provides detailed instructions for the installation, operation, and maintenance of your Edge Audio Xtreme Series EDX5000.1FD-E0 Monoblock Amplifier. The EDX5000.1FD-E0 is a high-performance Class D full-bridge amplifier designed for powerful audio output. Please read this manual thoroughly before attempting installation or operation to ensure proper use and to prevent damage.
1.1 Sikkerhedsforanstaltninger
- Frakobl altid bilens negative batteripol, før du foretager elektriske tilslutninger.
- Sørg for, at alle ledninger er korrekt ført og fastgjort for at forhindre skader eller kortslutninger.
- Brug passende ledningsføring til strøm- og jordforbindelser som angivet i denne manual.
- Undgå at montere amplifier in locations exposed to moisture or excessive heat.
- Kontakt en professionel installatør, hvis du er usikker på nogen del af installationsprocessen.
2. Pakkens indhold
Kontroller, at alle dele er til stede i pakken, før du fortsætter installationen.
- Edge Audio EDX5000.1FD-E0 Monoblock Amplivligere
- Fjernbetjening til bas
- Wiring for Remote Bass Control
Image 2.1: Contents of the EDX5000.1FD-E0 package, including the amplifier, remote bass control, and connecting cable.
Image 2.2: The retail packaging for the Edge Audio EDX5000.1FD-E0 Monoblock Amplivligere.
3. Funktioner
The Edge Audio Xtreme Series EDX5000.1FD-E0 amplifier incorporates advanced features for optimal audio performance:
- Monoblock power amplifier design for dedicated subwoofer applications.
- Max Power: 10,000 watts.
- Built-in active crossovers (High-Pass Filter and Low-Pass Filter) for precise sound shaping.
- Adjustable Bass Boost circuit for enhanced low-frequency response.
- Ultra-efficient Class D topology for high power output with minimal heat generation.
- Wideband frequency response up to 20kHz.
- Full bridge technology for efficient power delivery.
- Compact footprint for versatile installation options.
- Dimensions (H x W x D): 2.5 x 10.4 x 9.1 inches (64 x 264 x 230mm).
Billede 3.1: Top view of the EDX5000.1FD-E0 ampløfter, showcasing its compact design and heatsink fins.
4. Opsætning og installation
Korrekt installation er afgørende for din ydeevne og levetid ampFølg disse retningslinjer nøje.
4.1 Monteringssted
Monter amplifier in a dry, well-ventilated area, away from direct sunlight or heat sources. Ensure sufficient airflow around the amplifier's heatsink. The ampLifier er designet til overflademontering.
4.2 Ledningsforbindelser
All wiring should be securely connected and insulated to prevent short circuits. Use high-quality, appropriate gauge wiring.
4.2.1 Strømforbindelser
Tilslut amplifier to the vehicle's electrical system as follows:
- +12V (strøm): Connect a heavy-gauge power cable (e.g., 4 AWG or larger for 10,000W max power) directly from the positive terminal of the vehicle's battery to the +12V terminal on the amplifier. Install an appropriate fuse (not supplied) within 18 inches of the battery.
- GND (jord): Tilslut et kraftigt jordkabel af samme størrelse som strømkablet fra GND-terminalen på ampFastgør sikringen til en ren, umalet metaloverflade på køretøjets chassis. Sørg for en solid elektrisk forbindelse.
- REM (fjerntænding): Tilslut en ledning med mindre diameter (f.eks. 18 AWG) fra REM-terminalen på amplifier to the remote turn-on output of your head unit. This wire turns the amptænd og sluk for lyden med dit lydsystem.
Image 4.1: Power input terminals (+12V, REM, GND) on the EDX5000.1FD-E0 amplivligere.
4.2.2 Lydindgangsforbindelser
Connect your head unit's RCA outputs to the 'LOW INPUT' RCA jacks on the amplivligere.
4.2.3 Højttalerudgangstilslutninger
Tilslut din(e) subwoofer(e) til højttalerudgangsterminalerne på amplifier. Ensure correct polarity (+ to + and - to -) for optimal performance. Refer to your subwoofer's specifications for impedance matching.
Image 4.2: Rear panel of the EDX5000.1FD-E0 amplifier, showing low-level inputs, crossover controls, gain, bass boost, and speaker output terminals.
5. Betjeningsvejledning
Når den er installeret, skal du justere ampLifier-indstillinger for optimal lydkvalitet.
5.1 Kontrolpanel overview
Refer to Image 4.2 for the location of the following controls:
- HPF (højpasfilter): Adjusts the high-pass crossover frequency. For subwoofer applications, this should typically be set to its minimum or off, as a low-pass filter is usually preferred.
- LPF (lavpasfilter): Adjusts the low-pass crossover frequency (15Hz - 200Hz). This filters out frequencies above the set point, sending only low frequencies to the subwoofer. Set this according to your subwoofer and system requirements, typically between 60Hz and 100Hz.
- GEVINST: Passer til amplifier's input sensitivity to the output level of your head unit. Start with the gain at minimum, then slowly increase it until you hear distortion, then back off slightly. Do not use the gain control as a volume knob.
- BASS BOOST: Adjusts the level of bass enhancement (0dB - 12dB). Use sparingly to avoid distortion.
- FREQ (basforstærkningsfrekvens): Selects the center frequency for the bass boost (35Hz - 70Hz).
- FJERN: Port for connecting the wired remote bass control unit.
5.2 Fjernbetjening til bas
The included remote bass control allows for convenient adjustment of the subwoofer output level from the driver's seat. Connect it to the 'REMOTE' port on the amplivligere.
6. Vedligeholdelse
Regelmæssig vedligeholdelse er med til at sikre din bils levetid og ydeevne. amplivligere.
- Rensning: Rengør med jævne mellemrum amplifier's exterior with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners. Ensure ventilation fins are free of dust and debris.
- Tilslutningskontrol: Annually inspect all power, ground, remote, and speaker connections for tightness and corrosion. Loose connections can cause performance issues or damage.
- Miljø: Sørg for amplifier remains in a dry, stable environment, protected from extreme temperatures.
7. Fejlfinding
Hvis du oplever problemer med din ampLifier, se følgende almindelige problemer og løsninger, før du kontakter support.
- Ingen strøm:
- Check the in-line fuse near the battery.
- Verify +12V, GND, and REM connections are secure and receiving power.
- Ensure the remote turn-on wire is connected to a switched 12V source.
- Ingen lyd:
- Check all RCA input and speaker output connections.
- Verify head unit is powered on and outputting audio.
- Adjust the GAIN control.
- Forvrænget lyd:
- Reduce the GAIN setting.
- Check speaker wiring for shorts or incorrect polarity.
- Sørg for, at højttalerimpedansen matcher amplifier specifikationer.
- Reduce BASS BOOST if active.
- AmpOverophedning af kølemiddel:
- Sørg for tilstrækkelig ventilation omkring amplivligere.
- Check speaker impedance; running too low an impedance can cause overheating.
- Verify power and ground wire gauge is sufficient.
8. Specifikationer
Technical specifications for the Edge Audio Xtreme Series EDX5000.1FD-E0 Monoblock Amplivligere:
| Feature | Specifikation |
|---|---|
| Modelnummer | EDX5000.1FD-E0 |
| Mærke | KANT |
| Amplivligere Type | Monoblock, Class D, Full Bridge |
| Max Power | 10,000 watt |
| Frekvensrespons | Op til 20 kHz |
| Built-in Crossovers | Active (HPF, LPF) |
| Bass Boost | Adjustable (0-12dB) |
| Bas Boost Frequency | Adjustable (35Hz-70Hz) |
| Voltage | 230 volt (driftsspændingtage Range typically 12-14.4V DC for car audio) |
| Monteringstype | Overflademontering |
| Produktmål (H x B x D) | 2.5 x 10.4 x 9.1 tommer (64 x 264 x 230 mm) |
| Produktets vægt | 6.61 pund |
9. Garanti og support
For warranty information or technical support, please refer to the documentation provided at the time of purchase or contact your authorized Edge Audio dealer. Keep your proof of purchase for warranty claims.
