SplatRball SRB400-SUB Gel Ball Water Bead Blaster Instruction Manual

1. Produktet er slutview

The SplatRball SRB400-SUB is an electric gel ball water bead blaster designed for recreational use. It features semi-automatic and full-automatic firing modes, capable of shooting up to 8 rounds per second at velocities up to 200 feet per second. This kit provides everything needed to begin operation.

Sættets indhold:

• SplatRball SRB400-SUB Electric Water Blaster
• 400-round Magazine
• 10,000 rounds of SplatRBall Gel Ball Ammunition (dehydrated)
• Sikkerhedsbriller
• Genopladeligt 7.4V 1800mAh batteri
• USB opladningskabel
• Sling and Sling Clip

2. Sikkerhedsoplysninger

WARNING: WEAR EYE PROTECTION AT ALL TIMES WHEN USING THIS PRODUCT. NOT SUITABLE FOR YOUNG CHILDREN. ADULT SUPERVISION IS REQUIRED.

• Always wear the provided safety glasses or other ANSI Z87.1 rated eye protection when operating or near the SplatRball blaster.
• Sigt ikke mod øjne eller ansigt.
• Do not modify the blaster or gel balls.
• Use only SplatRball certified ammunition. Other ammunition may cause damage to the blaster or injury.
• Keep fingers and other objects clear of the firing mechanism and magazine well.
• Store the blaster and gel balls out of reach of small children.

3. Opsætning og klargøring

3.1. Hydrating Gel Balls

The SplatRball gel balls are supplied in a dehydrated state and must be soaked in water before use. This process allows them to expand to their full size (7.5mm diameter) and become soft and ready for firing.

1. Empty the desired amount of dehydrated gel balls into a large container.
2. Add a generous amount of clean water to fully submerge the gel balls.
3. Allow the gel balls to soak for a minimum of 4 hours. For best results, soak overnight (up to 8 hours).
4. Once fully hydrated, the gel balls will be soft and squishy. Drain any excess water before loading.

3.2. Opladning af batteriet

The blaster is powered by a rechargeable 7.4V 1800mAh battery. Ensure the battery is fully charged before first use and whenever power is low.

1. Connect the battery to the provided USB charging cable.
2. Sæt USB-opladerkablet i en kompatibel USB-strømkilde (f.eks. en computers USB-port eller en USB-vægadapter).
3. The charging indicator light on the cable will show the charging status (refer to cable instructions for specific light indications).
4. Når det er fuldt opladet, skal du frakoble batteriet fra opladeren.

3.3. Assembling the Blaster

Attach the magazine and sling to the blaster as follows:

1. Insert the charged battery into the designated battery compartment on the blaster (refer to the blaster's markings for location).
2. Align the magazine with the magazine well and push firmly until it clicks into place.
3. Attach the sling clip to the sling attachment point on the blaster, then attach the sling to the clip. Adjust the sling length for comfortable carrying.

4. Betjeningsvejledning

Before operating, ensure you have read and understood all safety information.

4.1. Indlæsning af magasinet

1. Ensure the blaster's safety switch is in the "SAFE" position (marked 'X').
2. Open the magazine's loading port.
3. Carefully pour the hydrated gel balls into the magazine until it is full (approximately 400 rounds).
4. Close the loading port securely.

4.2. Affyring af blasteren

1. With the magazine loaded and attached, hold the blaster firmly.
2. Move the safety switch to the desired firing mode:
   • 'O' for Semi-Automatic (single shot per trigger pull)
   • 'OOO' for Full-Automatic (continuous firing while trigger is held)
3. Aim at your target, ensuring no people or animals are in the line of fire.
4. Pull the trigger to fire.

5. Vedligeholdelse

Proper maintenance ensures the longevity and optimal performance of your SplatRball blaster.

• Rensning: After each use, especially if the blaster has been exposed to dirt or debris, wipe down the exterior with a damp klud. Sænk ikke blæsepistolen ned i vand.
• Gel Ball Storage: Store hydrated gel balls in a sealed container, submerged in water, to prevent them from dehydrating. They can be rehydrated if they shrink.
• Batteripleje: When not in use for extended periods, store the battery in a cool, dry place. Avoid overcharging or completely draining the battery.
• Fjernelse af papirstop: If the blaster jams, ensure the safety switch is on 'X' (Safe), remove the magazine, and gently clear any obstructions from the feeding mechanism. Do not force anything into the barrel.

6. Fejlfinding

If you encounter issues with your SplatRball blaster, refer to the following common problems and solutions:

7. Specifikationer

8. Garanti og support

Your SplatRball SRB400-SUB blaster comes with a manufacturer's warranty and support resources.

• Garanti: A 30-day warranty covers manufacturer defects. Please retain your proof of purchase.
• Brugermanual (PDF): For a downloadable PDF version of the user manual, please refer to the official product page or klik her.
• Mærkebutik: For additional products, accessories, and support, visit the official SPLATRBALL Store.
• Fabrikant: SPLATBALL