1. Sikkerhedsinstruktioner
Læs venligst disse instruktioner omhyggeligt inden installation og brug. Gem denne manual til senere brug.
- Installationen skal udføres af en kvalificeret elektriker i overensstemmelse med nationale elforskrifter.
- Ensure the power supply is disconnected before installation, maintenance, or repair.
- Overskrid ikke de maksimale belastningsværdier, der er angivet i denne manual.
- This device is designed for outdoor use and has an IP65 protection rating, making it dust-tight and protected against water jets.
- Enheden må ikke skilles ad eller modificeres.
2. Pakkens indhold
- 1 x SEBSON IR_CEIL_C Outdoor Motion Detector IP65
- Monteringsudstyr (skruer, vægdyvler)
- Instruktionsmanual
3. Produktet er slutview
The SEBSON IR_CEIL_C is an infrared motion detector designed for ceiling surface mounting in outdoor environments. It features a 360-degree detection angle and a maximum range of 20 meters, making it suitable for various applications such as activating outdoor lighting.
4. Installation
This motion detector is designed for surface mounting on ceilings. Ensure the mounting surface is stable and suitable for the device's weight.
4.1 Monteringssted
- Mount the detector at a height between 2.2 meters and 4 meters for optimal detection.
- Avoid mounting near heat sources (e.g., air vents, direct sunlight) or objects that might obstruct the detection area.
- Consider the detection range and angle (360° with a maximum 20m diameter) to cover the desired area effectively.
4.2 Ledningsføring
The device requires a 3-wire connection. Ensure the power supply is OFF before proceeding.
- Open the detector housing carefully.
- Connect the live (L), neutral (N), and switched live (L') wires to the corresponding terminals.
- Secure the cables using the provided strain relief.
- Close the housing, ensuring a tight seal for IP65 protection.
4.3 Dimensioner
5. Betjening
Once properly installed and configured, the SEBSON IR_CEIL_C motion detector will automatically activate the connected lighting when it detects movement within its detection zone and when the ambient light level falls below the set threshold. The light will remain on for the duration set by the 'TIME' dial and then turn off automatically if no further motion is detected.
6. Justeringer
The motion detector features two adjustable dials to customize its operation:
- TIME (Duration): This dial controls how long the connected light remains on after motion is detected. The adjustable range is from 10 seconds to 30 minutes. Turn the dial clockwise to increase the duration and counter-clockwise to decrease it.
- LUX (lysfølsomhed): This dial determines the ambient light level at which the motion detector becomes active. The adjustable range is from 3 LUX (darkness) to 2000 LUX (daylight). Turn the dial towards the 'sun' symbol for activation during daylight and towards the 'moon' symbol for activation only in low light conditions.
To access the adjustment dials, carefully open the detector housing as shown in the installation section.
7. Specifikationer
| Feature | Specifikation |
|---|---|
| Fabrikant | SEBSON |
| Modelnummer | IR_CEIL_C |
| Dimensioner (L x B x H) | 11.3 x 11.3 x 4.5 cm |
| Vægt | 145 gram |
| Farve | Hvid |
| Materiale | Plast |
| Beskyttelsesklasse | IP65 |
| Voltage | 230 volt |
| Maks. glødelampebelastning | 2000 watt |
| Max. LED/Energy Saving Lamp Indlæs | 1000 watt |
| Detektionsområde | Max. 20 Meters |
| Detektionsvinkel | 360° |
| Justering af tidsforsinkelse | 10 sekunder - 30 minutter |
| Light Sensitivity Adjustment | 3 - 2000 Lux |
| Monteringstype | Loftmontering |
| Strømkilde | El-kabel |
8. Fejlfinding
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Lyset tændes ikke, når der registreres bevægelse. | No power supply; LUX setting too high (daylight mode); faulty wiring; bulb failure. | Check power connection; adjust LUX setting to a lower value (moon symbol); verify wiring connections; replace bulb. |
| Lyset forbliver tændt konstant. | Constant motion in detection area; faulty sensor; wiring error. | Ensure no continuous motion; check for obstructions; verify wiring (L' connected correctly); if problem persists, contact support. |
| Light turns on too frequently or for too long. | TIME setting too long; LUX setting too low; detection area too wide. | Adjust TIME dial to a shorter duration; adjust LUX dial to a higher value; reposition detector or block part of the detection area if possible. |
| Detektionsområdet er for kort. | Mounting height too low; obstructions; temperature interference. | Ensure mounting height is within recommended range (2.2m-4m); remove obstructions; avoid mounting near strong heat sources. |
9. Vedligeholdelse
The SEBSON IR_CEIL_C motion detector requires minimal maintenance. To ensure optimal performance:
- Rengør sensorlinsen regelmæssigt med en blød kludamp cloth to remove dust or dirt that may affect detection. Do not use abrasive cleaners.
- Regularly check for any physical damage to the housing or wiring.
10. Garanti og support
For warranty information or technical support, please refer to the purchase documentation or contact SEBSON customer service directly. Keep your proof of purchase for any warranty claims.
