Okin Model JLDQ-11 & JLDQ.11.156.333P Brugsanvisning til el-lænestolsliftmotor

1. Introduktion

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Okin Model JLDQ-11 & JLDQ.11.156.333P Power Recliner Lift Chair Motor. Please read these instructions thoroughly before proceeding with installation or use.

2. Produktet er slutview

The Okin JLDQ.11.156.333P is a replacement actuator motor designed for power recliners and lift chairs. It is an original Okin JLDQ motor, suitable for replacing existing JLDQ.11.156.333P units.

Nøglefunktioner:

• Motortype: Linear actuator for recliner mechanisms.
• Komponenter: Consists of one motor and three distinct connectors.
• Udseende: Black (PA) housing with a silver-white (aluminum) shaft.
• slagtilfælde: 333 mm.
• Minimum Dimensions (Shrink): 156 mm.
• Maximum Dimensions (Extended): 489 mm.
• Belastningskapacitet: Push force: 650N, Pull force: 650N (approximately 146 lbs).
• Driftsfrekvens: On 1 minute / Off 8 minutes.
• Hastighed: 29VDC SMPS, 7 seconds without load.

3. Specifikationer

4. Sikkerhedsoplysninger

Vigtige sikkerhedsforanstaltninger:

• Vægt kapacitet: This product has a maximum weight capacity of approximately 146 lbs (650N). Exceeding this weight capacity may result in reduced product performance or potential safety risks.
• Stabil overflade: Always ensure the chair is used on a stable, hard floor surface.
• Design Limits: Do not subject the motor or chair to forces exceeding its design limits.
• Elektrisk sikkerhed: Ensure all electrical connections are secure and conform to local electrical codes. Disconnect power before performing any maintenance or installation.
• Børn og kæledyr: Hold børn og kæledyr væk fra bevægelige dele under drift.

5. Installation

This motor is designed as a direct replacement for Okin Model JLDQ.11.156.333P. Compatibility with other models or brands is not guaranteed due to variations in frame requirements, minimum install dimensions, stroke, and plug types. Verify your existing motor's brand and model number before installation.

Installationstrin:

1. Forberedelse: Disconnect the recliner from its power source. Position the recliner to access the motor area safely.
2. Identificer forbindelser: The motor set includes three types of connectors:
   • A 5-pin round plug for the switch hand control.
   • A 2-pin square plug with a clip for the power supply.
   • A 2-pin socket for a slaved motor (if applicable).
3. Fjern den gamle motor: Carefully detach the old motor from the recliner frame. Retain all existing mounting hardware (bolts, nuts, pins) as this replacement motor does not typically include them.
4. Monter ny motor: Align the new Okin JLDQ.11.156.333P motor with the mounting points on the recliner frame. Secure it using the retained hardware. Ensure the motor is firmly attached and moves freely without obstruction.
5. Tilslut ledninger: Connect the 5-pin round plug to the hand control, the 2-pin square plug to the power supply, and the 2-pin socket to any slaved motor if your recliner uses one. Ensure all connections are snug.
6. Test drift: Once installed and wired, reconnect the recliner to power. Test the motor's function using the hand control to ensure smooth and complete extension and retraction.

Note: If you are comfortable with basic mechanical tasks and have a socket wrench set and hex keys, you should be able to perform this installation. If unsure, consult a professional.

6. Betjening

Once correctly installed, the Okin JLDQ.11.156.333P motor operates in conjunction with your recliner's existing hand control. Pressing the appropriate buttons on the hand control will activate the motor, causing the recliner mechanism to extend or retract.

• Ensure the recliner is connected to a functional power outlet.
• Use the hand control to adjust the recliner to your desired position.
• Avoid continuous operation for more than 1 minute to prevent overheating. Allow an 8-minute rest period between extended uses.

7. Vedligeholdelse

Regular maintenance helps ensure the longevity and optimal performance of your Okin recliner motor.

• Rensning: The motor housing can be spot cleaned with a dry or slightly damp klæde. Undgå at bruge skrappe kemikalier eller overdreven fugt.
• Inspektion: Inspicer regelmæssigt motoren og dens forbindelser for tegn på slid, skader eller løse ledninger.
• Smøring: The internal components of the motor are factory-lubricated and generally do not require additional lubrication. If unusual noises occur, consult a professional.
• Miljøforhold: Ensure the motor is used in an indoor environment, as specified by the manufacturer.

8. Fejlfinding

If your recliner motor is not functioning as expected, perform the following basic troubleshooting steps:

1. Tjek strømforsyningen: Ensure the recliner is properly plugged into a working electrical outlet. Verify that the power supply unit (transformer) is receiving power and its indicator light (if present) is on.
2. Inspicer håndbetjeningen: Test the hand control for responsiveness. Sometimes, a faulty hand control can prevent the motor from operating.
3. Undersøg forbindelser: Check all motor connections (5-pin for hand control, 2-pin for power, 2-pin for slaved motor) to ensure they are securely seated and not damaged.
4. Motorkompatibilitet: Confirm that the installed motor is indeed the correct Okin JLDQ.11.156.333P model, especially if it's a recent replacement. Incompatible motors will not function correctly.
5. Forhindringer: Look for any physical obstructions preventing the recliner mechanism or motor rod from moving freely.

If these steps do not resolve the issue, it may indicate a more complex problem with the motor or electrical system. In such cases, it is recommended to contact a qualified technician or the manufacturer's support.

9. Garanti og support

For warranty information or technical support regarding your Okin JLDQ.11.156.333P Power Recliner Lift Chair Motor, please refer to the documentation provided at the time of purchase or contact Okin customer service directly. Ensure you have your model number (JLDQ.11.156.333P) and any purchase details available when seeking support.

You can find more information about Okin products and support on their official channels or through authorized distributors.