Givi Smart Mount_RC Smartphone Holder Support (S904B)

1. Introduktion

This manual provides detailed instructions for the installation, operation, and maintenance of your Givi Smart Mount_RC Smartphone Holder Support, model S904B. This product is designed to securely attach a compatible smartphone holder to your vehicle, typically on the brake fluid reservoir area, providing a stable platform for your device.

2. Sikkerhedsoplysninger

• Always ensure the mount is securely fastened before operating your vehicle.
• Bloker ikke din view of the road or vehicle controls with the mounted device.
• Regularly check all fasteners for tightness, especially after initial installation and before long journeys.
• Avoid over-tightening screws, which can damage components.
• Hvis du er usikker på et installationstrin, skal du kontakte en kvalificeret tekniker.

3. Pakkens indhold

Kontroller venligst, at alle komponenter er til stede i din pakke:

• Givi Smart Mount_RC Smartphone Holder Support (S904B) main unit
• Mounting hardware (screws, washers, spacers as required for brake fluid reservoir installation)
• Instruction leaflet (if included, refer to this manual for detailed steps)

Figur 3.1: The Givi Smart Mount_RC Smartphone Holder Support (S904B) main unit, showing its base, adjustable arm, and smartphone holder interface.

4. Opsætning og installation

The Givi Smart Mount_RC S904B is designed for mounting on a vehicle's brake fluid reservoir. Follow these steps for proper installation:

1. Identificér monteringssted: Locate the brake fluid reservoir on your motorcycle or scooter. The mount's base is designed to fit over the reservoir cap or an adjacent flat surface, utilizing existing screw points.
2. Forbered området: Ensure the mounting surface is clean and free from debris. If necessary, temporarily remove the existing screws from the reservoir cap or mounting plate.
3. Placer basen: Place the base of the S904B mount over the desired mounting points. Ensure it sits flush and does not interfere with the reservoir's function or other controls.
4. Fastgør basen: Use the provided screws and washers to firmly attach the mount's base to the vehicle. Tighten the screws evenly until the base is secure, but do not overtighten.
5. Juster armen: The mount features an adjustable ball joint system. Loosen the locking ring or knob on the arm to allow movement. Position the smartphone holder interface to your preferred viewing angle and reach.
6. Lås positionen: Once the desired angle is achieved, tighten the locking ring or knob to secure the arm in place. Ensure it is firm and does not move freely.
7. Attach Smartphone Holder: Connect your compatible Givi smartphone holder (sold separately) to the interface on the S904B support. Refer to your smartphone holder's manual for specific attachment instructions.

Figur 4.1: The Givi S904B mount installed on a motorcycle's brake fluid reservoir area, demonstrating its typical placement and integration with the vehicle's controls.

Figur 4.2: Illustration of the Givi S904B mount's side-to-side adjustability, allowing the user to fine-tune the position of the attached smartphone holder.

Figur 4.3: Illustration of the Givi S904B mount's up-and-down adjustability, enabling precise vertical positioning for optimal viewing.

5. Betjeningsvejledning

Once the Givi Smart Mount_RC S904B is securely installed and your compatible smartphone holder is attached, operating it is straightforward:

• Attaching a Smartphone: Follow the instructions provided with your specific Givi smartphone holder to securely attach your smartphone. Ensure the device is firmly seated and locked into the holder before riding.
• Justering Viewvinkel: If further adjustment of the viewing angle is needed, carefully loosen the locking ring on the S904B mount's arm, reposition the holder, and then re-tighten the ring firmly. Perform this adjustment only when the vehicle is stationary.
• Detaching a Smartphone: Follow the instructions provided with your specific Givi smartphone holder to safely remove your smartphone.

6. Vedligeholdelse

To ensure the longevity and proper function of your Givi Smart Mount_RC S904B, follow these maintenance guidelines:

• Rensning: Tør holderen af ​​med en blød kludamp klud til at fjerne støv og snavs. Undgå at bruge skrappe kemikalier eller slibende rengøringsmidler, da disse kan beskadige overfladen.
• Inspektion: Periodically inspect all components for signs of wear, damage, or corrosion. Check that all screws and fasteners remain tight.
• Smøring: The ball joint mechanism typically does not require lubrication. If movement becomes stiff, ensure no dirt or debris is obstructing the joint.

7. Fejlfinding

• Beslaget føles løst efter montering:

  Ensure all mounting screws are tightened securely. Check that the base is sitting flush against the mounting surface. If the issue persists, verify that the correct screws and spacers (if applicable) were used for your specific brake fluid reservoir.
• Smartphone holder wobbles or changes position:

  Tighten the locking ring or knob on the adjustable arm firmly. Ensure the smartphone holder itself is correctly attached to the S904B interface according to its own instructions.

• Difficulty attaching the mount to the brake fluid reservoir:

  Verify that the mount's base is compatible with the screw pattern and dimensions of your vehicle's brake fluid reservoir. Some vehicles may require specific adapters or may not be compatible. Consult your vehicle's manual or a Givi dealer for compatibility information.

8. Specifikationer

9. Garanti og support

For warranty information, technical support, or to purchase replacement parts, please refer to the official Givi website or contact your authorized Givi dealer. Keep your proof of purchase for warranty claims.

Givi Official Webwebsted: www.givi.it