1. Introduktion
This manual provides essential instructions for the safe operation, maintenance, and troubleshooting of your Total Tools Super Select Impact Drill 680W, model TG1061356. Please read this manual thoroughly before using the tool to ensure proper function and to prevent injury.
Vigtige sikkerhedsoplysninger: Always wear appropriate personal protective equipment (PPE) such as safety glasses, hearing protection, and gloves when operating power tools. Ensure the work area is clean and well-lit. Disconnect the drill from the power source before making any adjustments or changing accessories.
2. Opsætning
2.1 Udpakning
Carefully remove the drill and all accessories from the packaging. Inspect for any damage that may have occurred during transit. Retain packaging for future storage or transport.
2.2 Montering af hjælpehåndtaget
The auxiliary handle provides additional control and stability. To attach:
- Løsn ekstrahåndtagetamp ved at dreje den mod uret.
- Skub håndtaget på forsiden af boremaskinen.
- Juster håndtaget til en behagelig position for dit greb.
- Spænd clamp by rotating it clockwise until secure.
Figure 1: Total Tools Super Select Impact Drill with auxiliary handle. The handle is positioned at the front of the drill for improved control.
2.3 Installing a Drill Bit (Keyed Chuck)
This drill features a 13mm keyed chuck for secure bit retention.
- Afbryd strømmen: Ensure the drill is unplugged from the power outlet.
- Åbn chuck: Insert the chuck key into one of the holes on the chuck and rotate counter-clockwise to open the chuck jaws.
- Indsæt bit: Place the drill bit into the chuck, ensuring it is centered and inserted as far as possible without touching the chuck jaws' base.
- Spænd borepatronen: Rotate the chuck key clockwise to tighten the chuck jaws firmly around the drill bit. Use all three holes on the chuck to ensure even and secure tightening.
- Fjern nøgle: Always remove the chuck key before operating the drill.
2.4 Strømtilslutning
Connect the drill's power cord to a suitable 220V AC power outlet. Ensure the outlet is properly grounded and rated for the drill's power requirements (680W).
3. Betjeningsvejledning
3.1 Tænd/sluk
- At tænde: Press the trigger switch. The drill speed is variable depending on how far the trigger is pressed.
- To Lock On (for continuous operation): Press the trigger switch fully, then press the lock-on button (usually located on the side of the handle).
- To Turn Off (from locked-on position): Press the trigger switch fully again, then release it.
- To Turn Off (from momentary operation): Simply release the trigger switch.
3.2 Hastighedsjustering
The drill features variable speed control via the trigger switch. For precise control, a speed pre-selection dial may be present (refer to specific model features if available, otherwise rely on trigger control). Maximum speed is 3000 RPM.
3.3 Mode Selection (Drill / Impact)
This impact drill offers two modes: rotary drilling and impact drilling. A selector switch, typically located on the top or side of the drill, allows you to choose the appropriate mode.
- Rotary Drilling Mode (Drill Symbol): For drilling into wood, metal, plastics, and for screwdriving.
- Slagboretilstand (hammersymbol): Til boring i murværk, beton og tegl.
Figur 2: Side view of the drill, highlighting the mode selector switch (typically near the chuck) and the product label with specifications.
3.4 Omvendt funktion
The drill is equipped with a reverse rotation function, useful for removing jammed drill bits or for screwdriving applications. The forward/reverse switch is usually located above the trigger.
- Push the switch to the left for forward rotation (drilling).
- Push the switch to the right for reverse rotation (removing bits).
Sørg altid for, at boremaskinen er stoppet helt, før du ændrer rotationsretningen.
3.5 Boreteknikker
- Generel: Tryk konstant og jævnt. Tving ikke boret. Lad borekronen udføre arbejdet.
- Træ: Use high speeds and wood-specific drill bits.
- Metal: Use lower speeds and metal-specific drill bits. Apply cutting oil for harder metals to prolong bit life.
- Masonry/Concrete (Impact Mode): Use impact-rated masonry bits. Apply firm, consistent pressure. The impact action will assist in breaking through hard materials.
4. Vedligeholdelse
Regular maintenance ensures the longevity and safe operation of your drill.
4.1 Rengøring
- Afbryd strømmen: Always unplug the drill before cleaning.
- Ydre: Wipe the exterior of the drill with a clean, damp klæde. Brug ikke skrappe kemikalier eller slibende rengøringsmidler.
- Ventilationsåbninger: Hold ventilationsåbningerne fri for støv og snavs for at forhindre overophedning. Brug trykluft om nødvendigt.
4.2 Vedligeholdelse af borepatron
Periodically clean the chuck jaws to ensure proper gripping of drill bits. A small amount of light machine oil can be applied to the chuck jaws to keep them moving smoothly.
4.3 Carbon Brush Inspection (If Applicable)
Some power tools use carbon brushes that wear over time. If your drill experiences reduced power or intermittent operation, the carbon brushes may need inspection or replacement. This procedure should ideally be performed by a qualified service technician.
4.4 Opbevaring
Opbevar boremaskinen et tørt og sikkert sted, utilgængeligt for børn. Beskyt den mod direkte sollys og ekstreme temperaturer.
5. Fejlfinding
Before attempting any repairs, ensure the drill is unplugged from the power source.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Boremaskinen starter ikke. | Ingen strømforsyning; defekt netledning/stik; problem med afbryder. | Check power outlet; inspect cord for damage; contact service if switch is faulty. |
| Reduceret effekt eller intermitterende drift. | Worn carbon brushes; motor overheating; loose connections. | Inspect/replace carbon brushes (if applicable); allow drill to cool; check connections. |
| Drill bit jams frequently. | Incorrect bit for material; excessive pressure; dull bit. | Use correct, sharp bit; reduce pressure; clear debris from hole. |
| Overdreven vibration eller støj. | Loose chuck; bent drill bit; internal component issue. | Ensure chuck is tight; replace bent bit; contact service for internal issues. |
If the problem persists after attempting these solutions, contact an authorized service center.
6. Specifikationer
The following are the technical specifications for the Total Tools Super Select Impact Drill 680W (Model: TG1061356):
| Feature | Detalje |
|---|---|
| Mærke | Totalværktøjer |
| Modelnummer | TG1061356 |
| Strømkilde | Elektrisk med ledning |
| Maksimal effekt | 680 watt |
| Voltage | 220 volt |
| Chuck-type | Indtastet |
| Maksimal Chuck-størrelse | 13 millimeter |
| Hastighed | 3000 o/min (uden belastning) |
| Justerbar hastighed | Yes (Variable via trigger) |
| Omvendt funktion | Ja |
| Hammer Functionality | Yes (Impact Drill) |
| Varens vægt | 209 g (0.21 kilogram) |
| Produktdimensioner | 10 x 20 x 37 cm |
Figure 3: Approximate dimensions of the Total Tools Impact Drill.
7. Garanti og support
Total Tools products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Total Tools website. For technical support, service, or spare parts, please contact your local Total Tools authorized dealer or service center.
Gem venligst dit købsbevis for garantikrav.
