Joysway J4C05 sender og J5C01R modtager brugermanual

1. Introduktion

Welcome to the instruction manual for your Joysway J4C05 4-channel transmitter and J5C01R 5-channel receiver. This system operates in Mode 2, which is standard for many RC applications, providing intuitive control over your model. Please read this manual thoroughly before operating your equipment to ensure safe and efficient use.

Sikkerhedsforanstaltninger: Always operate your RC equipment responsibly. Ensure batteries are charged, perform pre-flight checks, and be aware of your surroundings. Keep the equipment away from moisture, extreme temperatures, and direct sunlight.

An image showing the black Joysway J4C05 4-channel transmitter on the left and the smaller black J5C01R 5-channel receiver on the right, connected by a wire. The transmitter features two control sticks, various switches, and a 2.4GHz FHSS label. The receiver has multiple ports for connecting servos and other components.

2. Komponenter overview

2.1 Pakkens indhold

• Joysway J4C05 4-Channel Transmitter (Mode 2)
• Joysway J5C01R 5-Channel Receiver
• Instruktionsmanual

2.2 Transmitter (J4C05) Features

The J4C05 is a 4-channel 2.4GHz FHSS (Frequency Hopping Spread Spectrum) transmitter designed for reliable control. It operates in Mode 2, meaning the left stick controls throttle and rudder, while the right stick controls aileron and elevator.

• Kontrolpinde: Two proportional sticks for primary flight controls.
• Trim Levers: Fine-tuning adjustments for each primary control channel.
• Kontakter: Auxiliary switches for additional functions (e.g., gear, flaps, depending on model setup).
• Strømindikator: LED til at vise strømstatus.

2.3 Receiver (J5C01R) Features

The J5C01R is a compact 5-channel 2.4GHz FHSS receiver designed to pair seamlessly with the J4C05 transmitter. It provides multiple ports for connecting servos, Electronic Speed Controllers (ESCs), and other accessories.

• Kanaler: 5 output channels for various control surfaces and functions.
• BIND knap: Bruges til at parre modtageren med senderen.
• LED-indikator: Shows binding status and signal reception.

3. Opsætning

3.1 Batteriinstallation (sender)

1. Locate the battery compartment on the back of the J4C05 transmitter.
2. Skub batteridækslet op.
3. Insert the required number of AA batteries (typically 4) according to the polarity markings (+/-).
4. Luk batteridækslet forsvarligt.

3.2 Forbindelse af sender og modtager

Binding is the process of electronically linking the transmitter and receiver so they communicate exclusively with each other.

1. Sørg for, at senderen er slukket.
2. Connect a power source (e.g., ESC with BEC, or a separate receiver battery) to the J5C01R receiver.
3. Press and hold the BIND button on the J5C01R receiver while powering it ON. The receiver's LED should flash rapidly.
4. While the receiver LED is flashing, turn ON the J4C05 transmitter.
5. Modtagerens LED-lampe skal lyse konstant, hvilket indikerer en vellykket binding.
6. Turn OFF both the transmitter and receiver, then turn them ON again in the normal sequence (transmitter first, then receiver) to confirm the bind.

3.3 Connecting Servos and ESC

Connect your servos and Electronic Speed Controller (ESC) to the appropriate channels on the J5C01R receiver. Ensure correct polarity (signal, positive, negative).

4. Betjeningsvejledning

4.1 Tjek før flyvning

Before each operation, perform the following checks:

• Ensure both transmitter and receiver batteries are fully charged.
• Verify that all control surfaces (ailerons, elevator, rudder) move correctly and in the proper direction in response to stick inputs.
• Tjek alle forbindelser for sikkerhed.
• Confirm that the throttle stick is at its lowest position before powering on the model.

4.2 Basic Control (Mode 2)

• Venstre pind (gas/ror):
      Vertikal bevægelse: Controls throttle (up for more power, down for less).
      Horisontal bevægelse: Controls rudder (left for left yaw, right for right yaw).
• Højre pind (kløft/højde):
      Vertikal bevægelse: Controls elevator (up for nose up, down for nose down).
      Horisontal bevægelse: Controls aileron (left for left roll, right for right roll).

4.3 Trimjusteringer

Trim levers are used to make small, precise adjustments to the neutral position of your control surfaces. If your model drifts without stick input, use the corresponding trim lever to correct it. For example, if the model drifts left, apply right aileron trim until it flies straight.

4.4 Range Testing

Before operating your model at a distance, perform a range test to ensure proper signal integrity. Consult your model's specific manual for detailed range testing procedures, as they can vary.

5. Vedligeholdelse

5.1 Rengøring

Wipe the transmitter and receiver with a soft, dry cloth. Do not use solvents or abrasive cleaners, as they may damage the plastic or electronics. Avoid getting moisture into the units.

5.2 Opbevaring

When not in use, store the transmitter and receiver in a cool, dry place, away from direct sunlight and extreme temperatures. Remove batteries from the transmitter if storing for extended periods to prevent leakage.

5.3 Pleje af batterier

Always use fresh, good quality batteries. Replace batteries when the power indicator shows low voltage. Dispose of used batteries responsibly according to local regulations.

6. Fejlfinding

If you encounter issues with your Joysway J4C05/J5C01R system, refer to the table below for common problems and their solutions.

7. Specifikationer

7.1 Tekniske specifikationer

• Produktmodel: JY881155
• ASIN: B08X178V14
• Dato først tilgængelig: 15. februar 2022

Transmitter (J4C05)

• Kanaler: 4
• Frekvens: 2.4 GHz FHSS
• Mode: 2 (Left stick: Throttle/Rudder; Right stick: Aileron/Elevator)
• Strømforsyning: 4 x AA batterier (medfølger ikke)

Receiver (J5C01R)

• Kanaler: 5
• Frekvens: 2.4 GHz FHSS
• Strømforsyning: 4.8V - 6V (typically from ESC BEC or receiver battery)

8. Garanti og support

8.1 Garantioplysninger

Joysway products are manufactured to high quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or contact your point of purchase. Keep your proof of purchase for any warranty claims.

8.2 Kundesupport

If you require further assistance or have questions not covered in this manual, please visit the official Joysway webwebstedet eller kontakt deres kundesupportafdeling. Kontaktoplysninger kan typisk findes på produktemballagen eller i producentens webwebsted.