1. Introduktion
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Service First OEM 9.3 TON 208/230/60/3 Compressor. Please read this manual thoroughly before installation or operation.
This compressor is an American Standard / Trane OEM / Service First Unit Specific Component, designed for various American Standard & Trane Systems.
2. Sikkerhedsoplysninger
Always observe all local and national electrical and safety codes. Installation and servicing should only be performed by qualified personnel.
- Elektrisk fare: Afbryd strømmen før servicering.
- Højtryk: Refrigerant systems operate under high pressure. Use appropriate safety equipment.
- Varme overflader: Compressor surfaces can become hot during operation. Allow to cool before handling.
- Korrekt løft: This unit is heavy (400 Pounds). Use proper lifting techniques and equipment to prevent injury.
3. Opsætning og installation
The Service First OEM 9.3 TON Compressor is designed for permanent mounting. Ensure the mounting surface is stable and level.
3.1 Udpakning
Carefully remove the compressor from its packaging. Inspect for any shipping damage. Report any damage to the carrier immediately.
Figur 1: Forside view of the Service First 9.3 TON Compressor. This image shows the main body of the compressor, which is cylindrical with a domed top, and features two copper pipe connections for refrigerant lines and an electrical connection box on the side.
3.2 Elektriske forbindelser
This compressor operates on 208/230V, 60Hz, 3-phase power. Ensure the power supply matches these specifications. All wiring must comply with local and national electrical codes.
3.3 Tilslutninger af kølemiddelledning
The compressor features braze sweat connections. Use proper brazing techniques to connect refrigerant lines, ensuring a leak-free system. This unit uses Mineral Oil (OIL00042).
Figure 2: An illustrative stamp indicating "TRANE OEM Component". This image signifies the authenticity and origin of the compressor as an Original Equipment Manufacturer part for Trane systems.
4. Betjeningsvejledning
Once installed and all connections are secure and leak-tested, the compressor is ready for operation as part of the HVAC system. Refer to the overall system's user manual for specific operational sequences.
- Ensure proper refrigerant charge according to system specifications.
- Monitor system pressures and temperatures during initial startup.
- Verify correct rotation of the compressor motor (for 3-phase units).
5. Vedligeholdelse
Regular maintenance is crucial for the longevity and efficiency of the compressor. Always disconnect power before performing any maintenance.
5.1 Rutinemæssige kontroller
- Kontroller de elektriske forbindelser for tæthed og tegn på overophedning.
- Check refrigerant lines for leaks.
- Monitor oil level and quality if applicable to the system design.
5.2 Rengøring
Keep the compressor and surrounding area clean and free of debris to ensure proper heat dissipation.
6. Fejlfinding
This section provides general guidance for common issues. For complex problems, contact a qualified HVAC technician.
| Problem | Mulig årsag | Løsning |
|---|---|---|
| Kompressor starter ikke | No power, faulty wiring, control issue, thermal overload | Check power supply, inspect wiring, consult system controls, allow compressor to cool |
| Low cooling capacity | Low refrigerant charge, restricted airflow, dirty coils, compressor inefficiency | Check for leaks and recharge, clean coils, inspect fan operation, consult technician |
| Usædvanlig støj | Loose mounting, internal mechanical issue, liquid slugging | Check mounting bolts, consult technician for internal issues, ensure proper superheat |
7. Specifikationer
- Modelnummer: COM08290_ver4
- Mærke: Service først
- Kapacitet: 9.3 TON
- Voltage: 208/230V
- Frekvens: 60 Hz
- Fase: 3-faset
- Forbindelser: Braze Sweat
- Olietype: Mineral Oil (OIL00042)
- Produktdimensioner: 48 x 48 x 48 tommer
- Vægt: 400 pund
- Monteringstype: Permanent Mount
- Materiale: Metal
- Form: Rektangulær
- Dato først tilgængelig: 3. december 2020
8. Garanti og support
For warranty information, please refer to the documentation provided with your specific HVAC system or contact Service First directly. As an OEM component, warranty terms may be tied to the complete system.
For technical support or service inquiries, please contact your authorized Service First dealer or a qualified HVAC professional.
