Anton/Bauer VM2 Dual V-Mount Batterioplader Brugsanvisning

Indledning

The Anton/Bauer VM2 Dual V-Mount Battery Charger is a lightweight and portable solution designed for simultaneously charging two V-Mount batteries while also providing power to camera accessories. This intelligent charger features an XLR4 output for converting AC to DC power or delivering battery power to compatible devices. Its compact design makes it ideal for transport and use in various production environments.

Figur 1: Forside view of the Anton/Bauer VM2 Dual V-Mount Battery Charger.

Opsætning

Follow these steps to set up your VM2 Dual V-Mount Battery Charger:

1. Pak opladeren ud: Carefully remove the VM2 charger from its packaging.
2. Tilslut til vekselstrøm: Locate the AC input port on the side of the charger. Connect the provided power cable to the charger and then to a standard AC power outlet (100-240V).
3. Aktiver strøm: Flip the 'ON/OFF' switch to the 'ON' position. The charger is now ready for operation.
4. Deploy Support Stand: For stable placement, extend the integrated support stand located at the bottom of the charger.

Figur 2: Bagside view of the charger showing the AC input and power switch.

Drift

The VM2 charger offers intelligent charging and power delivery capabilities:

• Batteriopladning: Attach up to two V-Mount batteries to the V-Mount plates on the charger. The charger will automatically begin intelligent charging. For example, an Anton/Bauer GO 90 (98Wh 8A) battery typically charges in approximately 3 hours.
• Samtidig opladning: The VM2 is designed to charge both batteries concurrently, optimizing your workflow.
• DC Power Output: The XLR4 DC output (16.7VDC 4.5A) can be used to power devices that accept an XLR input, either directly from AC power when the charger is plugged in, or by drawing power from attached batteries.
• Opladningsindikatorer: Observe the indicator lights on the front panel to monitor the charging status of each battery.

Figure 3: The VM2 charger with two V-Mount batteries attached for simultaneous charging.

Figure 4: The VM2 charger demonstrating the XLR4 DC output connection.

Opretholdelse

To ensure the longevity and optimal performance of your Anton/Bauer VM2 charger, consider the following maintenance guidelines:

• Rensning: Regularly wipe the exterior of the charger with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
• Ventilation: Ensure the built-in fan and ventilation openings are clear of obstructions to allow for proper cooling during operation.
• Opbevaring: Når den ikke er i brug, skal du opbevare opladeren på et køligt, tørt sted væk fra direkte sollys og ekstreme temperaturer.
• Kabelpleje: Inspect power cables and connectors periodically for any signs of wear or damage. Replace if necessary.

Fejlfinding

The VM2 charger incorporates advanced safety features to protect your batteries and devices. If you encounter an issue, consider the following:

• Charging Stops Automatically: The intelligent safety technology in the VM2 will automatically stop charging if a fault is detected or if an attached battery reaches an overvoltage condition. Check the battery for issues or try a different battery.
• Ingen strøm/Indikatorer slukket: Ensure the charger is securely plugged into a working AC outlet and the 'ON/OFF' switch is in the 'ON' position. Check the power cable for damage.
• Overophedning: The built-in fan helps maintain optimal operating temperature. Ensure ventilation openings are not blocked. If the charger feels excessively hot, disconnect it and allow it to cool down in a well-ventilated area.

For persistent issues not covered here, please refer to the support section.

Specifikationer

Garanti og support

For information regarding warranty coverage, technical support, or service for your Anton/Bauer VM2 Dual V-Mount Battery Charger, please visit the official Anton/Bauer webwebstedet eller kontakt deres kundeserviceafdeling. Gem din købskvittering som købsbevis i tilfælde af garantikrav.