DSC PG9914 PowerSeries Neo Trådløs PowerG Digital Smart Dobbeltfunktion Indendørs Kæledyrsimmun PIR-bevægelsesdetektor Brugermanual

Indledning

The DSC PG9914 is a sophisticated, dual-function indoor Passive Infrared (PIR) motion detector designed for enhanced security and environmental monitoring. This device integrates reliable motion detection with temperature monitoring capabilities, making it a versatile addition to your security system. Utilizing PowerG wireless technology, the PG9914 offers superior immunity to false alarms and is specifically engineered to be pet-immune, distinguishing between human movement and pets weighing up to 38 kg (85 lb). Its compact design allows for unobtrusive placement, particularly in corners.

Sikkerhedsoplysninger

• Kun indendørs brug: This device is designed for indoor environments. Do not expose it to water, high humidity, or extreme temperatures.
• Batterihåndtering: Use only the specified battery type. Ensure correct polarity when installing. Dispose of used batteries according to local regulations. Do not attempt to recharge non-rechargeable batteries.
• Installation: Install the detector in a location free from direct sunlight, heat sources, or strong air currents that could cause false alarms. Avoid placing it near windows or vents.
• Opretholdelse: Forsøg ikke at åbne eller reparere enheden selv. Overlad al service til kvalificeret personale.
• Kæledyrsimmunitet: While designed to be pet-immune, optimal performance is achieved when installed at the recommended height and away from areas where pets might climb.

Pakkens indhold

Bekræft at alle varer er til stede i din pakke:

• DSC PG9914 Motion Detector Unit
• Monteringsudstyr (skruer, ankre)
• Battery (pre-installed or separate, typically Lithium-Ion)
• Lynvejledning (denne manual indeholder detaljerede instruktioner)

Opsætning

1. Batteriinstallation/aktivering

The PG9914 typically comes with a Lithium-Ion battery that offers a long lifespan (6-8 years with typical use). The battery compartment is easily accessible.

1. Locate the battery compartment on the back or side of the detector.
2. If a pull tab is present, remove it to activate the pre-installed battery.
3. If installing a new battery, ensure correct polarity (+/-) as indicated inside the compartment.
4. Luk batterirummet forsvarligt.

2. Mounting Location Selection

Choose a mounting location that provides optimal coverage and minimizes false alarms. Consider the following:

• Højde: Typically mounted at 2.1m to 2.4m (7 ft to 8 ft) for optimal pet immunity.
• Dækning: Position to cover the primary entry points or high-traffic areas. The detector has an operating range of up to 12 m (39 ft).
• Undgå: Direct sunlight, heat sources (radiators, vents), strong air currents, and areas where pets can climb directly into the detection zone.
• Hjørneplacering: The small size and design are perfectly shaped for unobtrusive corner placement, which often provides excellent room coverage.

Figur 1: Forside view of the DSC PG9914 motion detector. This image displays the sleek, white design of the unit, highlighting the main detection lens area.

Figur 2: Side view of the DSC PG9914 motion detector. This perspective illustrates the compact and unobtrusive profile, ideal for corner mounting.

3. Montering af detektoren

1. Once the optimal location is identified, mark the screw holes on the wall or corner.
2. Bor forhuller om nødvendigt, og isæt vægankre.
3. Fastgør monteringsbeslaget (hvis det er separat) eller selve detektoren til væggen med de medfølgende skruer.
4. Sørg for, at detektoren er fastgjort og stabil.

4. Pairing with PowerSeries Neo Alarm Systems

The PG9914 is compatible with PowerSeries Neo alarm systems. Refer to your PowerSeries Neo system's manual for specific instructions on enrolling new wireless devices. General steps typically include:

• Put your PowerSeries Neo panel into enrollment mode.
• Activate the PG9914 (e.g., by triggering its tamper switch or performing a walk test).
• The panel should detect and register the new device.
• Assign the detector to a specific zone and configure its settings (e.g., pet immunity level, if adjustable via the panel).

Drift

Bevægelsesdetektion

The PG9914 uses Passive Infrared (PIR) technology to detect changes in infrared radiation caused by movement of warm bodies. When motion is detected within its field of view, the detector sends a signal to the connected PowerSeries Neo alarm system.

• Registreringsområde: Op til 12 meter (39 fod).
• Fresnel and Cylindrical Lenses: These specialized lenses ensure uniform detection sensitivity across the entire coverage area, eliminating the need for vertical adjustment.

Husdyrsimmunitet

A key feature of the PG9914 is its advanced pet immunity, achieved through Target Specific Imaging (TSI) technology. This allows the detector to differentiate between the infrared signatures of humans and common household pets.

• The detector is designed to ignore pets weighing up to 38 kg (85 lb).
• For optimal pet immunity, ensure the detector is mounted at the recommended height and that pets cannot get within close proximity to the detector's lens by climbing on furniture.

Temperaturovervågning

In addition to motion detection, the PG9914 also monitors ambient temperature. This feature can be integrated with your PowerSeries Neo system to provide alerts for significant temperature changes, enhancing overall environmental awareness within your protected space.

Opretholdelse

Rensning

To ensure optimal performance, keep the detector's lens clean and free from dust. Use a soft, dry, lint-free cloth to gently wipe the surface. Do not use abrasive cleaners, solvents, or excessive moisture.

Udskiftning af batteri

The PG9914 features a long-life battery (typically 6-8 years). Your PowerSeries Neo system will usually indicate a low battery condition for the detector. When this occurs, replace the battery promptly.

1. Disarm your alarm system before replacing the battery to avoid triggering an alarm.
2. Open the battery compartment (refer to "Battery Installation" in the Setup section).
3. Remove the old battery and dispose of it responsibly according to local regulations.
4. Insert a new, fresh Lithium-Ion battery, ensuring correct polarity.
5. Luk batterirummet forsvarligt.
6. Test the detector by performing a walk test to confirm it is communicating with the alarm panel.

Fejlfinding

Specifikationer

Garanti og support

For warranty information, technical support, or service inquiries regarding your DSC PG9914 motion detector, please contact your authorized DSC dealer or the security system installer. You can also visit the official DSC webwebsted for produktdokumentation og supportressourcer.

Note: Attempting to service the device yourself may void the warranty.