ARRIS C250 Kulfiber FPV250 Racing Quad RTF Brugermanual

1. Introduktion

Tak for købetasing the ARRIS C250 Carbon Fiber FPV250 Racing Quad. This manual provides essential information for the safe operation, setup, maintenance, and troubleshooting of your racing quadcopter. Please read this manual thoroughly before operating the device to ensure proper function and to prevent damage or injury.

1.1 Sikkerhedsforanstaltninger

• Always operate the quadcopter in open areas, away from people, animals, and obstacles.
• Ensure all batteries are fully charged and properly connected before each flight.
• Inspect the quadcopter for any damage before and after each flight.
• Hold hænder og ansigt væk fra roterende propeller.
• Do not operate in adverse weather conditions (e.g., strong winds, rain).
• Adhere to all local regulations and laws regarding drone operation.
• This product is not a toy and should be operated by experienced individuals or under adult supervision.

2. Pakkens indhold

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact ARRIS customer support.

• 1 x ARRIS C250 Racing Quad Frame
• 4 x ARRIS S2205 2300KV Brushless Motors
• 4 x Flycolor Raptor BLS Pro BLHeli_S 30A ESC
• 4 x ARRIS 5045 3-blade Propeller (2CW + 2CCW)
• 1 x F3 Flight Controller (Standard Version)
• 1 x ARRIS Cat FPV Mini Camera
• 1 x 5.8G 200mw 32CH FPV TX
• 1 x FPV Transmitter Antenna
• 1 x FlySky FS-i6-M2 Transmitter with FS-iA6B receiver
• 1 x ARRIS Buzzer TMB12A05
• 2 x 7 Colors RGB 5050 LED
• 1 x ARRIS 14.8V 1500mah 50C Lipo Battery

3. Komponent overview

Familiarize yourself with the main components of your ARRIS C250 Racing Quad.

Figur 3.1: The ARRIS C250 Racing Quadcopter shown with its accompanying FlySky FS-i6-M2 radio transmitter.

Figur 3.2: Detaljeret view of the ARRIS C250 Racing Quad with key components labeled, including motors, propellers, FPV camera, video transmitter, and LED board.

3.1 nøglekomponenter

• ARRIS S2205 2300KV Brushless Motors: High-performance motors for racing.
• Flycolor Raptor BLS Pro BLHeli_S 30A ESC: Electronic Speed Controllers managing motor power.
• F3 Flight Controller: The central processing unit for flight stability and control.
• ARRIS Cat FPV Mini Camera: Provides real-time video feed for First Person View flyvende.
• 5.8G 200mw FPV TX & Antenna: Transmits the video signal from the camera to your FPV receiver/goggles.
• FlySky FS-i6-M2 Transmitter: Remote control for piloting the quadcopter.
• ARRIS 14.8V 1500mah 50C Lipo Battery: Power source for the quadcopter.

Figur 3.3: Et nærbillede view of the ARRIS S2205 2300KV Brushless Motor, indicating its model and KV rating.

Figur 3.4: Detaljeret view of an ARRIS 20A BLHeli Brushless ESC and the XT60 female power connector on the quadcopter frame.

Figur 3.5: The Foxeer XAT700M Mini Camera, demonstrating its adjustable 45-degree tilt angle for optimal FPV viewing during flight.

Figur 3.6: The 7 Colors RGB 5050 LED Board, illustrating various color combinations for visual identification and aesthetics.

4. Opsætning

4.1 Batteriopladning

The ARRIS C250 uses a 14.8V 1500mAh 50C LiPo battery. Always use a compatible LiPo balance charger. Refer to your charger's manual for specific instructions.

1. Connect the LiPo battery's main discharge plug (XT60) and balance plug to the appropriate ports on your LiPo charger.
2. Select the correct battery type (LiPo) and cell count (4S for 14.8V) on your charger.
3. Set the charging current. For a 1500mAh battery, a 1.5A (1C) charge rate is recommended for safety and longevity.
4. Start the charging process and monitor the battery. Never leave charging batteries unattended.
5. Disconnect the battery once charging is complete.

Figur 4.1: The ARRIS C250 Racing Quad with the 4S 1500mAh 50C LiPo battery securely mounted on top of the frame.

4.2 Transmitter Setup (FlySky FS-i6-M2)

Your ARRIS C250 comes with a pre-bound FlySky FS-i6-M2 transmitter and FS-iA6B receiver. Minimal setup should be required, but familiarization with the transmitter is crucial.

1. Install 4 AA batteries into the FlySky FS-i6-M2 transmitter.
2. Tænd for senderen.
3. Connect the fully charged LiPo battery to the quadcopter. The quadcopter should emit a series of beeps, and the receiver's LED should indicate a successful connection (solid light).
4. Familiarize yourself with the stick controls:
   • Venstre pind (tilstand 2): Throttle (up/down), Yaw (left/right)
   • Højre pind (tilstand 2): Pitch (up/down), Roll (left/right)
5. Ensure all switches are in their disarmed/off positions before connecting the quadcopter battery.

4.3 Propelinstallation

The ARRIS C250 uses 5045 3-blade propellers. Ensure correct rotation direction for each motor.

1. Identify clockwise (CW) and counter-clockwise (CCW) propellers. Typically, CW propellers are installed on motors that spin clockwise, and CCW on motors that spin counter-clockwise.
2. The ARRIS C250 typically uses a 'props out' configuration, meaning the front-left and rear-right motors spin CCW, and the front-right and rear-left motors spin CW.
3. Carefully place the correct propeller onto each motor shaft.
4. Secure the propellers with the provided propeller nuts, ensuring they are tight but not overtightened.

4.4 Tjek før flyvning

• Verify battery is fully charged and securely mounted.
• Check all propellers for damage and ensure they are securely fastened.
• Confirm all wires and connections are secure and not interfering with propellers.
• Ensure the FPV camera lens is clean.
• Power on the transmitter first, then connect the quadcopter battery.
• Perform a range check of the transmitter before flying.

5. Betjeningsvejledning

5.1 Til- og frakobling

To arm the motors (make them ready to spin), typically move the throttle stick to the lowest position and the yaw stick to the far right for a few seconds. The motors will spin slowly, indicating they are armed. To disarm, move the throttle stick to the lowest position and the yaw stick to the far left. Refer to your flight controller's specific arming sequence if different.

5.2 Første flyvning

1. Place the armed quadcopter on a flat, level surface in an open area.
2. Slowly increase the throttle. The quadcopter should lift off smoothly.
3. Use small, gentle stick movements to control pitch, roll, and yaw.
4. Practice hovering at a low altitude to get a feel for the controls.
5. When landing, slowly decrease the throttle until the quadcopter gently touches down. Disarm the motors immediately after landing.

5.3 FPV Flying

For FPV flying, you will need compatible FPV goggles or a monitor. Ensure your FPV receiver is tuned to the same frequency as the quadcopter's 5.8G 200mw FPV TX.

Figur 5.1: Close-up of the ARRIS FPV Racing 5.8G TX Antenna connected to the 5.8G 200mW 40CH Video Transmitter, responsible for sending the FPV video feed.

1. Power on your FPV goggles/monitor and tune to the correct channel.
2. Verify you have a clear video feed from the quadcopter.
3. Start with slow, controlled flights in an open area until you are comfortable with FPV navigation.

6. Vedligeholdelse

6.1 Generel pleje

• Keep the quadcopter clean and free from dirt, dust, and moisture.
• Store the quadcopter and battery in a cool, dry place away from direct sunlight.
• Avoid exposing electronic components to extreme temperatures.

6.2 Inspektion og udskiftning af propeller

• Regularly inspect propellers for cracks, bends, or nicks. Damaged propellers can cause instability and reduce flight performance.
• Replace any damaged propellers immediately. Always replace with the correct type (5045 3-blade) and ensure correct CW/CCW orientation.

6.3 Pleje af batterier

• Overoplade eller overaflade aldrig LiPo-batterier.
• Store LiPo batteries at a 'storage charge' (around 3.8V per cell) if not used for extended periods.
• Discontinue use of any swollen or damaged batteries.

7. Fejlfinding

8. Specifikationer

9. Garanti og support

For warranty information, technical support, or replacement parts, please contact ARRIS customer service directly. Refer to the official ARRIS webwebstedet eller din købsdokumentation for kontaktoplysninger.

It is recommended to register your product if an option is available to receive updates and support.