Tiny Hawk 2 New Model Indoor FPV Racing Drone User Manual

1. Introduktion

The EMAX Tinyhawk II is an advanced indoor FPV racing drone designed for an optimized user experience. It features significant improvements in flight performance and durability, making it suitable for various flight situations. This manual provides essential information for setting up, operating, and maintaining your Tinyhawk II drone.

Figure 1: EMAX Tinyhawk 2 FPV Racing Drone

2. Produktfunktioner

• 1-2S Capable: Supports both 1S and 2S batteries for versatile power options.
• Runcam Nano 2 Camera: Equipped with a high-quality FPV camera for crisp colors, wide dynamic range, and sharp optics.
• 25-100-200 switchable VTX: Adjustable video transmission power (25mw, 100mw, 200mw) for optimal range and video clarity.
• 16000KV Motors: High-performance motors providing increased power and faster propeller speeds.
• Redesigned Frame with Adjustable Angle Canopy: Enhanced durability and an adjustable camera mount for customized flight angles.
• Throttle Response LED System: Integrated LEDs in the frame increase in brightness based on throttle input.

3. Hvad er der i æsken

Figure 2: Included components with the Tinyhawk 2

• Propeller (Spare sets included)
• Battery (Lithium Polymer, 300mAh included)
• Blade (Additional blades for replacement)
• Camera (Integrated RunCam Nano 2 FPV Camera)
• Remote Control (Note: This is a Bind-N-Fly (BNF) model, a compatible remote controller is not included and must be purchased separately.)

4. Produktspecifikationer

5. Opsætningsvejledning

5.1 Indledende inspektion

Upon unboxing, carefully inspect the Tinyhawk II for any visible damage. Ensure all propellers are securely attached and free from bends or cracks. Verify that the camera is properly seated in its mount.

5.2 Opladning og installation af batteri

Charge the provided Lithium Polymer battery using a compatible LiPo charger. Always follow the charger's instructions and safety guidelines. Once charged, carefully connect the battery to the drone's power port. Ensure a secure connection.

5.3 Binding to a Transmitter (BNF Model)

As a Bind-N-Fly (BNF) model, the Tinyhawk II requires binding to a compatible FPV radio transmitter. Refer to your transmitter's manual for specific binding procedures. Typically, this involves putting both the drone and the transmitter into binding mode. Once bound, the drone's indicator lights will confirm a successful connection.

5.4 Tjek før flyvning

Before each flight, perform the following checks:

• Sørg for, at batteriet er fuldt opladet og sikkert tilsluttet.
• Verify all propellers are intact and spinning freely.
• Check that the FPV camera feed is clear and stable on your goggles/monitor.
• Confirm proper control response from your transmitter (throttle, roll, pitch, yaw).
• Ensure adequate clear space for flight, especially indoors.

6. Betjeningsvejledning

6.1 kontroller overview

The Tinyhawk II operates using standard FPV drone controls. Familiarize yourself with the functions of your transmitter's sticks:

• Left Stick (Mode 2): Throttle (up/down) and Yaw (left/right).
• Right Stick (Mode 2): Pitch (forward/backward) and Roll (left/right).

6.2 Start og landing

To arm the motors, typically move the left stick (throttle) to the bottom-right or activate an arming switch on your transmitter. Slowly increase throttle to lift off. For landing, gently decrease throttle until the drone touches down. Disarm motors immediately after landing.

6.3 Flight Modes and VTX Power

The Tinyhawk II supports various flight modes configurable via Betaflight (advanced users). It also features switchable VTX power (25mw, 100mw, 200mw). For indoor flying, 25mw is the standard. Higher power settings (100mw, 200mw) are available for increased range and object penetration in larger areas or outdoors.

6.4 FPV System Usage

Power on your FPV goggles or monitor and tune to the correct video frequency matching the drone's VTX. Ensure a clear video feed before initiating flight. The RunCam Nano 2 camera provides a high-quality image for an immersive FPV experience.

Video 1: Overståetview of the Tinyhawk 2's capabilities and flight characteristics.

7. Vedligeholdelse

7.1 Udskiftning af propel

Regularly inspect propellers for damage (bends, cracks, chips). Damaged propellers can cause instability and reduce flight performance. To replace, gently pull the old propeller off the motor shaft and push a new one firmly into place, ensuring it's fully seated.

7.2 Rengøring

After flights, especially outdoors, clean any dirt, dust, or debris from the drone's frame, motors, and camera lens. Use a soft brush or compressed air for motors and a microfiber cloth for the camera lens.

7.3 Opbevaring

Store the Tinyhawk II in a cool, dry place away from direct sunlight. Always remove the battery before storing the drone for extended periods. Store LiPo batteries at a storage voltage (around 3.8V per cell) to prolong their lifespan.

8. Fejlfinding

8.1 No Power / Drone Not Turning On

• Tjek batteri: Sørg for, at batteriet er fuldt opladet og korrekt tilsluttet.
• Undersøg stik: Look for any loose or damaged battery connectors on both the drone and the battery.

8.2 Drone Not Binding to Transmitter

• Bindende procedure: Re-verify that both the drone and transmitter are in the correct binding mode as per their respective manuals.
• Kompatibilitet: Ensure your transmitter is compatible with the Tinyhawk II's receiver protocol.
• Afstand: Keep the drone and transmitter close during the binding process.

8.3 Unstable Flight / Drifting

• Propeller Damage: Check all propellers for damage and replace if necessary.
• Kalibrering: Recalibrate the accelerometer in Betaflight (if applicable).
• Motorproblemer: Inspect motors for debris or damage.

8.4 No FPV Video Feed

• VTX Power: Ensure the VTX is powered on and set to an appropriate power level.
• Frekvensmatch: Verify that your FPV goggles/monitor are on the exact same frequency as the drone's VTX.
• Antenne: Check if the VTX antenna is securely connected and undamaged.

9. Garanti og support

Specific warranty information for the EMAX Tinyhawk II is typically provided with the product packaging or available on the manufacturer's official webwebsted. Gem venligst din købsbevis til garantikrav.

For technical support, troubleshooting assistance beyond this manual, or spare parts inquiries, please visit the official EMAX webwebstedet eller kontakt deres kundeserviceafdeling. Kontaktoplysningerne findes normalt på produktemballagen eller deres webwebsted.