Triumph NSS-8SQ Classic Lift User Manual

Indledning

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Triumph NSS-8SQ Classic Lift. This 4-post storage and service car lift is designed to maximize vertical space and facilitate vehicle maintenance. Please read this manual thoroughly before attempting to assemble or operate the lift to ensure proper function and safety.

Vigtige sikkerhedsoplysninger

Manglende overholdelse af disse sikkerhedsinstruktioner kan resultere i alvorlig personskade eller død.

• Always read and understand the entire manual before installation or operation.
• Ensure the installation area is a level concrete surface capable of supporting the lift's weight and the maximum load. Consult a structural engineer if unsure.
• Do not exceed the lift's maximum load capacity of 8000 lbs.
• Hold hænder, fødder og tøj væk fra bevægelige dele.
• Ensure all safety locks are engaged before working under a lifted vehicle.
• Only qualified personnel should perform electrical connections. The hydraulic pump requires a 110V, 30A dedicated circuit.
• Hold arbejdsområdet rent og godt oplyst.
• Never operate the lift if any part is damaged or malfunctioning.
• Use appropriate personal protective equipment (PPE) during installation and operation.

Pakkens indhold

Your Triumph NSS-8SQ Classic Lift package includes the following components:

• 4 Post Lift structure
• 3 Plastic Drip Trays
• 1 Jack Tray
• 4 Casters for mobility
• 1 110V Motor with hydraulic pump
• 2 Vehicle Stop Plates (removable)
• 2 Vehicle Loading Ramps (removable)

Image showing the included accessories: three plastic drip trays, a steel jack tray, and the caster kit for moving the lift.

Opsætning og montering

Forberedelse af webstedet

• Ensure your garage or installation area has sufficient ceiling height for the lift's maximum height (84 inches) plus the height of the vehicle.
• The lift requires a minimum overall length of 141 inches and overall width of 106 inches for installation.
• The concrete floor must be at least 4 inches thick and cured for at least 28 days, with a minimum strength of 3000 PSI.
• Provide a dedicated 110V, 30A electrical outlet for the hydraulic power unit.

Monteringstrin

1. Udpakning: Carefully unpack all components. Note that one of the runways contains the hydraulic ram and will be significantly heavier than the other. An engine hoist or similar equipment may be required for safe handling of heavier components.
2. Erecting Vertical Supports: Position the four vertical posts according to the desired layout.
3. Installing Horizontal Supports: With assistance, slide the horizontal cross beams onto the vertical supports. These do not weigh much and can be walked down the vertical supports by manipulating the safety locks.
4. Mounting Runways: Lift and bolt the runways onto the horizontal supports. The heavier runway with the hydraulic ram should be positioned appropriately.
5. Tilslutning af kabler: Route the pre-installed cables from the heavy runner to the appropriate vertical supports. Adjust cable tension using the jam nuts at the top of each vertical support, ensuring they are even.
6. Installing Hydraulic Pump and Motor: Mount the 110V motor and hydraulic pump unit to the designated post. Fill the reservoir with approximately 3 gallons of hydraulic oil (e.g., Mobil DTE 26 or equivalent, not included). Connect the power unit to the dedicated 110V, 30A electrical circuit. The unit features a UL Listed Plug for safety.
7. Installing Safety Lock Lever: Attach the safety lock lever and its associated hardware.
8. Attaching Ramps and Stop Plates: Secure the aluminum approach ramps to the ends of the runways. Install the vehicle stop plates at the opposite ends. Both are removable and interchangeable.
9. Indledende test: Before loading a vehicle, perform a test run of the lift to ensure smooth operation and proper engagement of safety locks.

Samlet set view of the Triumph NSS-8SQ Classic Lift, showing the four posts, runways, and approach ramps.

Detail of the hydraulic power unit, featuring a UL Listed Plug and a durable steel oil tank.

View of the robust 5/16 inch lock rods and the textured aluminum approach ramps.

Betjeningsvejledning

Tjekliste før operation

• Verify that the lift area is clear of obstructions.
• Kontroller hydraulikvæskeniveauet.
• Inspect cables and pulleys for wear or damage.
• Sørg for, at alle bolte og fastgørelseselementer er stramme.

Lifting a Vehicle

1. Carefully drive the vehicle onto the runways, ensuring it is centered and within the lift's capacity.
2. Engage the vehicle's parking brake.
3. Activate the hydraulic pump to raise the lift.
4. Løft liften til den ønskede arbejdshøjde.
5. Once at the desired height, lower the lift slightly until the safety locks engage securely. This transfers the load from the hydraulic system to the mechanical locks.
6. Always ensure all four safety locks are fully engaged before working under the vehicle.

Sænkning af et køretøj

1. Ensure the area beneath the lift is clear of personnel and obstructions.
2. Slightly raise the lift to disengage the safety locks.
3. Operate the lowering valve to slowly descend the lift.
4. Guide the vehicle off the ramps once it reaches the ground level.

Opretholdelse

Regular maintenance is crucial for the longevity and safe operation of your lift.

• Dagligt/før hver brug: Inspect cables, pulleys, and safety locks for any signs of wear, damage, or obstruction. Check for hydraulic fluid leaks.
• Månedlig: Check hydraulic fluid level and top off if necessary. Inspect all fasteners for tightness. Lubricate all moving parts, including cables and pulleys.
• Årligt: Perform a thorough inspection of the entire lift structure, including posts, runways, and welds. Check for proper cable tension and adjust if needed.
• Keep the lift clean and free of debris.

Fejlfinding

This section addresses common issues you might encounter with your Triumph NSS-8SQ lift.

Tekniske specifikationer

Side view dimensions of the lift, including overall height (84") and overall length (141").

Top view dimensions, indicating overall width (106") and runway length (132").

Front view dimensions, highlighting the drive-through width (93").

Garanti og support

For warranty information, technical support, or to order replacement parts, please contact the manufacturer, Triumph, or your authorized dealer. Retain your proof of purchase for warranty claims.