Onyx KX80 80W AC/DC Charger Instruction Manual

1. Introduktion

The Onyx KX80 is a compact and versatile 80W AC/DC multi-chemistry battery charger and discharger. Designed for hobbyists, it supports a wide range of battery types including LiPo, LiHV, Li-Ion, LiFe, NiCd, NiMH, and Pb. This manual provides essential information for the safe and efficient operation, setup, and maintenance of your KX80 charger.

2. Sikkerhedsforanstaltninger

• Brug altid opladeren i et godt ventileret område, væk fra brandfarlige materialer.
• Never leave the charger unattended while in use.
• Ensure correct battery type and cell count settings before initiating any charge or discharge cycle. Incorrect settings can lead to battery damage, fire, or injury.
• Forsøg ikke at oplade beskadigede eller hævede batterier.
• Keep the charger away from moisture, dust, and direct sunlight.
• Use only the provided or approved power cables and adapters.
• Dette produkt er ikke et legetøj. Opbevares utilgængeligt for børn.

3. Pakkens indhold

Bekræft at alle varer er til stede i din pakke:

• Onyx KX80 80W AC/DC Charger
• AC strømledning
• DC Input Cable (Alligator Clips)
• Banana Plug to Deans Adapter
• JST-XH Balance Adapter Board

Image: The Onyx KX80 charger displayed with its complete set of included accessories, including power cables, charging leads, and a balance adapter board.

4. Produktet er slutview

The Onyx KX80 features a user-friendly interface with a 2-line LCD screen and four control buttons for easy navigation and operation.

Billede: En vinklet view of the Onyx KX80 charger, showcasing dens kompakte design og betjeningselementer på frontpanelet.

Front Panel Controls and Display:

Image: A close-up of the charger's front panel, highlighting the LCD screen displaying 'LiPo BALANCE CHG' and the four control buttons: Stop, BATT/PROG, Status/Decrease, and Start/Enter.

• LCD skærm: Displays charging parameters, battery status, and menu options.
• Stop-knap: Terminates the current operation or returns to the previous menu.
• BATT/PROG Button: Enters the battery program selection menu.
• Status / Decrease Button (Left Arrow): Navigerer gennem menupunkter eller reducerer værdier.
• Start / Enter Button (Right Arrow): Confirms selections or starts operations.

Sidepaneler:

Image: The side of the charger featuring the AC power input port and the DC power input port, labeled 'DC POWER'.

• AC strømindgang: For connecting the charger to a standard wall outlet (100-240V AC).
• DC strømindgang: For connecting the charger to a DC power source (11-18V DC), such as a car battery.

Image: The opposite side of the charger, showing the main output terminals (red and black banana plug ports) and the multi-pin balance port for LiPo/LiHV/Li-Ion/LiFe batteries.

• Udgangsterminaler: Red (+) and Black (-) banana plug ports for connecting the main charging lead to the battery.
• Balance Port: Multi-pin port for connecting the balance lead of LiPo, LiHV, Li-Ion, or LiFe batteries (1-6 cells).

5. Opsætning

5.1 Strømtilslutning

1. AC strøm: Connect the AC power cord to the charger's AC input port, then plug the other end into a standard wall outlet (100-240V AC).
2. Jævnstrøm: Alternatively, connect the DC input cable (with alligator clips) to the charger's DC input port. Connect the red clip to the positive (+) terminal and the black clip to the negative (-) terminal of a 11-18V DC power source (e.g., a 12V car battery).

The charger will power on, and the LCD screen will illuminate.

5.2 Batteritilslutning

1. Connect the appropriate charging lead (e.g., Banana plug to Deans adapter) to the charger's main output terminals (red to red, black to black).
2. Connect the other end of the charging lead to your battery's main power connector.
3. For LiPo, LiHV, Li-Ion, or LiFe batteries, also connect the battery's balance lead to the appropriate slot on the JST-XH balance adapter board, then connect the adapter board to the charger's balance port. Ensure the correct cell count slot is used.

6. Betjeningsvejledning

6.1 Menunavigation

Brug BATT/PROG button to cycle through the main battery program types. Use the Status / Decrease og Start / Enter buttons to navigate within menus and adjust values. Press Start / Enter to confirm a selection or start an operation. Press Stop to go back or end an operation.

6.2 Charging LiPo/LiHV/Li-Ion/LiFe Batteries

1. Connect the battery as described in Section 5.2.
2. Trykke BATT/PROG until the desired battery type (e.g., 'LiPo BATT') is displayed.
3. Trykke Start / Enter to enter the LiPo program menu.
4. Select the desired mode (e.g., 'LiPo BALANCE CHG' for balanced charging, 'LiPo CHARGE' for fast charging, 'LiPo FAST CHG' for fast charging, 'LiPo STORAGE' for storage charge). Balanced charging is recommended for optimal battery life and safety.
5. Adjust the charge current (e.g., 0.1A - 6.0A) using the Status / Decrease og Start / Enter buttons. A common guideline is to charge at 1C (e.g., for a 5000mAh battery, charge at 5.0A).
6. Adjust the cell count (e.g., '3S' for a 3-cell battery). The charger will automatically detect the cell count if connected correctly via the balance port.
7. Tryk og hold Start / Enter for 3 seconds to confirm settings and begin the charging process. The charger will perform a cell count check. Confirm by pressing Start / Enter igen.
8. The display will show real-time charging information.
9. Once charging is complete, the charger will beep, and the display will indicate 'FULL'. Press Stop and disconnect the battery.

6.3 Charging NiCd/NiMH Batteries

1. Connect the battery's main power connector to the charger's output terminals. Balance connection is not required for NiCd/NiMH.
2. Trykke BATT/PROG until 'NiMH BATT' or 'NiCd BATT' is displayed.
3. Trykke Start / Enter to enter the program menu.
4. Select 'NiMH CHARGE' or 'NiCd CHARGE'.
5. Adjust the charge current and cell count (if applicable).
6. Tryk og hold Start / Enter for 3 seconds to begin charging.
7. Disconnect the battery when charging is complete.

6.4 Charging Pb (Lead-Acid) Batteries

1. Connect the battery's main power connector to the charger's output terminals.
2. Trykke BATT/PROG until 'Pb BATT' is displayed.
3. Trykke Start / Enter to enter the program menu.
4. Select 'Pb CHARGE'.
5. Adjust the charge current and voltage (f.eks. 2V, 6V, 12V).
6. Tryk og hold Start / Enter for 3 seconds to begin charging.
7. Disconnect the battery when charging is complete.

6.5 Discharging Batteries

The KX80 offers a discharge function (2A, 10W). This is useful for cycling NiCd/NiMH batteries or preparing LiPo/LiHV/Li-Ion/LiFe batteries for storage.

1. Tilslut batteriet.
2. Navigate to the desired battery type program.
3. Select the 'DISCHARGE' mode.
4. Adjust the discharge current and final voltage (hvis relevant).
5. Tryk og hold Start / Enter for 3 seconds to begin discharging.
6. The charger will stop automatically when the set parameters are reached.

7. Vedligeholdelse

• Hold opladeren ren og fri for støv. Brug en blød, tør klud til rengøring.
• Brug ikke opløsningsmidler eller slibende rengøringsmidler.
• Regularly inspect all cables and connectors for damage. Replace any damaged components immediately.
• Opbevar opladeren på et køligt, tørt sted, når den ikke er i brug.

8. Fejlfinding

9. Specifikationer

10. Garanti og support

For warranty information and technical support, please refer to the official Onyx product webwebstedet eller kontakt din autoriserede forhandler. Gem din købskvittering som købsbevis.