VONROC MS500AC radial geringssav brugermanual

1. Introduktion

This manual provides essential information for the safe and effective use of your VONROC MS500AC Radial Mitre Saw. Please read these instructions carefully before operating the machine and retain them for future reference. Proper use and maintenance will ensure optimal performance and extend the life of your tool.

Image 1.1: The VONROC MS500AC Radial Mitre Saw, showcasing its main components including the saw blade, motor housing, and base.

2. Generelle sikkerhedsinstruktioner

ADVARSEL: Læs alle sikkerhedsadvarsler, instruktioner, illustrationer og specifikationer, der følger med dette elværktøj. Undladelse af at følge alle instruktionerne nedenfor kan resultere i elektrisk stød, brand og/eller alvorlig personskade.

2.1. Arbejdsområdesikkerhed

• Hold arbejdsområdet rent og godt oplyst. Rodede eller mørke områder inviterer til ulykker.
• Brug ikke elværktøj i eksplosive atmosfærer, såsom i nærheden af ​​brændbare væsker, gasser eller støv. Elværktøj danner gnister, som kan antænde støv eller dampe.
• Hold børn og omkringstående væk, mens du betjener et elværktøj. Distraktioner kan få dig til at miste kontrollen.

2.2. Elektrisk sikkerhed

• Elværktøjsstik skal passe til stikkontakten. Modificer aldrig stikket på nogen måde.
• Undgå kropskontakt med jordede eller jordede overflader, såsom rør, radiatorer, komfurer og køleskabe. Der er en øget risiko for elektrisk stød, hvis din krop er jordet eller jordet.
• Udsæt ikke elværktøj for regn eller våde forhold. Vand, der trænger ind i et elværktøj, øger risikoen for elektrisk stød.

2.3. Personlig sikkerhed

• Brug altid øjenbeskyttelse. Brug sikkerhedsbriller, beskyttelsesbriller eller ansigtsskærm.
• Wear hearing protection. Prolonged exposure to noise can cause hearing damage.
• Klæd dig ordentligt på. Bær ikke løstsiddende tøj eller smykker. Hold dit hår og tøj væk fra bevægelige dele.
• Vær opmærksom, hold øje med, hvad du laver, og brug din sunde fornuft, når du betjener et elværktøj.

2.4. Mitre Saw Specific Safety

• Brug altid den korrekte klinge til det materiale, der skal skæres.
• Sørg for, at arbejdsemnet er sikkert klamped før skæring.
• Ræk aldrig ind i savklingeområdet, når saven kører eller er tilsluttet strøm.
• Lad klingen nå fuld hastighed, før du begynder at save.
• Use the laser guide and LED light for improved accuracy and visibility, but always verify the cut line manually.

Billede 2.1: Eks.ample of safety labels and warnings found on the saw, including laser radiation warnings.

3. Pakkens indhold

Carefully unpack the contents and check for any damage or missing parts. If any parts are missing or damaged, please contact VONROC customer support.

• VONROC MS500AC Radial Mitre Saw
• Saw Blade (Ø216 mm, 40-toothed)
• Støvpose
• Unbrakonøgle
• Arbejdsstykke Clamp
• Bench Extensions (2 units)
• Brugervejledning (dette dokument)

4. Produktet er slutview

The VONROC MS500AC is a powerful 2000W radial mitre saw designed for precise cutting of wood. It features a 216mm saw blade, integrated laser guidance, and an LED work light for enhanced accuracy and visibility.

4.1. Nøglefunktioner

• Laser enhed: Provides a clear line for controlled and straight sawing.
• Integreret LED lys: Illuminates the workpiece for optimal visibility, even in low-light conditions.
• Adjustable Mounting Features: Allows for versatile and precise adjustments for various cuts.
• Large Saw Capacity: Capable of cutting wood pieces up to 65 x 340 mm.
• Kraftig motor: 2000W motor with 4700 RPM for efficient cutting.

Image 4.1: Detail of the laser guide and LED work light, highlighting their position above the saw blade.

5. Opsætning og montering

Before first use, ensure the saw is securely mounted on a stable workbench. Follow these steps for initial setup:

5.1. Mounting the Saw

1. Place the mitre saw on a firm, level surface.
2. Secure the saw to the workbench using appropriate bolts or clamps through the mounting holes in the base.

5.2. Attaching Bench Extensions

The included bench extensions provide additional support for longer workpieces.

1. Slide the bench extensions into the designated slots on either side of the saw base.
2. Tighten the locking screws to secure them in place.

5.3. Montering af støvposen

Attach the dust bag to the dust extraction port to collect sawdust during operation.

1. Locate the dust extraction port on the saw.
2. Securely attach the dust bag to the port. Ensure it is firmly in place to prevent detachment during use.

5.4. Adjusting the Work Piece Clamp

Emnet clamp helps secure material for safe and accurate cutting.

1. Indsæt emnet clamp into the designated hole on the saw table.
2. Adjust its position to firmly hold the workpiece against the fence.

6. Betjeningsvejledning

Always wear appropriate personal protective equipment (PPE) including eye protection, hearing protection, and a dust mask when operating the saw.

6.1. Basic Cutting Procedure

1. Forbered emnet: Mark your desired cut line on the material.
2. Placering af emne: Placer emnet fast mod anslaget og fastgør det med emneklemmen.amp. Ensure the material is fully supported.
3. Adjust Angles (if necessary):
   • Geringsvinkel: Adjust the turntable to the desired mitre angle (up to 45 degrees left or right). Lock the turntable in place.
   • Affasningsvinkel: Tilt the saw head to the desired bevel angle (up to 45 degrees). Lock the saw head in place.
4. Activate Laser and LED: Turn on the laser guide and LED work light for precise alignment and improved visibility.
5. Start saven: Press the power switch to start the motor. Allow the blade to reach full speed before beginning the cut.
6. Udfør klipning:
   • For straight cuts, slowly lower the saw blade through the workpiece.
   • For radial (sliding) cuts, pull the saw head towards you, lower the blade into the material, and then push the saw head smoothly through the workpiece.
7. Release Saw: Når savningen er færdig, slip tænd/sluk-knappen og lad klingen stoppe helt, før savhovedet hæves.
8. Fjern emne: Fjern forsigtigt det afskårne materiale.

Image 6.1: Demonstrating a cut with the saw, showing proper hand placement and dust extraction hose.

Image 6.2: Illustration of the saw head tilting for bevel cuts, adjustable up to 45 degrees.

Image 6.3: Illustration of the saw base rotating for mitre cuts, adjustable from -45 to +45 degrees.

Image 6.4: Detail of the measurement scale and adjustable fence for accurate workpiece positioning.

6.2. Using the Laser Guide and LED Light

The laser guide projects a red line onto the workpiece, indicating the exact cutting path. The LED light illuminates the cutting area. These features can be activated independently or together via dedicated switches.

• Always verify the laser line against your marked cut line before starting the saw.
• The LED light is particularly useful in dimly lit workshops or when working on intricate cuts.

7. Vedligeholdelse

Regular maintenance ensures the longevity and safe operation of your VONROC MS500AC Mitre Saw. Always disconnect the saw from the power supply before performing any maintenance or cleaning.

7.1. Rensning

• After each use, clean the saw thoroughly to remove sawdust and debris. Use a brush or compressed air.
• Tøm støvposen regelmæssigt.
• Tør udvendige overflader af med adamp klæde. Brug ikke skrappe kemikalier eller opløsningsmidler.
• Hold ventilationsåbningerne fri for at forhindre overophedning.

7.2. Udskiftning af kniv

A dull or damaged saw blade can lead to poor cuts and increased risk of kickback. Replace the blade when necessary.

1. Afbryd saven fra strømforsyningen.
2. Refer to the saw's specific instructions for accessing and removing the blade guard.
3. Use the provided Allen wrench to loosen the blade retaining bolt.
4. Carefully remove the old blade, noting its rotation direction.
5. Install the new blade, ensuring the teeth are oriented correctly for cutting.
6. Tighten the blade retaining bolt securely and reassemble the blade guard.

7.3. Laser and LED Maintenance

• Keep the laser aperture and LED lens clean from dust and debris to maintain optimal visibility.
• If the laser becomes misaligned, refer to the specific adjustment procedures in the full manual (if available) or contact customer support.

8. Fejlfinding

This section addresses common issues you might encounter with your mitre saw. For problems not listed here, please contact VONROC customer support.

9. Tekniske specifikationer

10. Garanti og kundesupport

VONROC products are manufactured to high-quality standards. In the unlikely event of a defect or malfunction, please refer to your purchase documentation for warranty details or contact VONROC customer support directly.

For assistance, spare parts, or technical inquiries, please visit the official VONROC website or contact their customer service department. Always have your model number (MS500AC) and purchase date available when contacting support.

Visit VONROC Official Webwebsted